GBC FOTON 30 Automated Laminator Bedienungsanleitung

any form or by any means without prior written permission of ACCO Brands. GBC® and Foton™30 are

registered trademarks of ACCO Brands Corporation.

Trouble Shooting Guide V1.0

TROUBLE SHOOTING

SYMPTON

POSSIBLE CAUSE

CORRECTIVE ACTION

Pressing the Power

button does not

turn the machine

The power cord may not

be inserted all the way

into outlet

Fully Insert plug into outlet

Make sure the outlet has power

Status Indicator

Red:

Door Error Indicator Red:

Paper Jam Error Indicator

Red:

Film Empty Indicator Red:

Cutter Error Indicator Red

Remove any paper from the feeder tray. Open and Close both the

laminator door and the feeder door. Ensure they are fully closed

Open the feeder door, and remove any paper from the feeder tray.

Close the feeder door.

If the above does not clear the error, press and hold the RUN button for

10 seconds to manually feed film. Film should begin to exit the machine

and Jam should clear.

If Jam error remains, open laminator door and look to see if film leader

is caught on an obstacle or the rollers. DO NOT CUT the film. Lift-up the

film leader and replace it in proper position. Shut Laminator door and

hold the run button for 10 Seconds.

Cartridge End of Roll label has been detected. Replace the film cartridge

with new cartridge and shut the laminator door.

The cutter could not initiate a cut, or did not finish a cut.

Press the manual cut button one time to try and activate the cutter. Not

resolved, try the following:

Observe the film at the exit of the laminator to see if the film is not cut

or partially cut.

Film is not cut:

Press and hold the RUN button for about 10-20 seconds to

manually advance the film. If there is laminated media in the

exit of the laminator, hold the RUN button until the media has

fully exited the laminator. Now press the manual cut button to

see if the cutter is activated.

Film is Partially Cut:

Open the laminator door and look to see if you can see the

trimmer blade. It will be near the back of the laminator

partway through the film. Using scissors cut the film hanging

out the exit of the laminator. Then using caution not to put

your fingers near the trimmer knife, carefully remove the

cartridge. Close the laminator door and try to manually cycle

any form or by any means without prior written permission of ACCO Brands. GBC® and Foton™30 are

registered trademarks of ACCO Brands Corporation.

Status Indicator

Red Continued:

Cutter Error Indicator Red

Continued:

the cutter. If the cutter works Re-insert your cartridge. Might

need to trim off the leading edge of film where the cutter

jammed. If you need to trim the film leave 4 inches (100mm)

of sealed film as the cartridge leader. Re-insert the cartridge.

The machine once warmed-up will automatically thread the

film and activate the trimmer.

If the cutter does not work after the above steps contact GBC customer

service for warranty repair.

Film Wrinkles on

output

Film Misaligned

Press and hold the RUN button to manually advance the film. After 5 –

20 inches (125 –500mm) of film has been advanced the wrinkle should

work themselves out. If wrinkle clear press the manual cut button and

you are ready to begin.

If wrinkles still present, open the laminator door. Grasp the film exiting

the laminator and hold it Taut while closing the laminator door. Repeat

above step and wrinkles should disappear.

Film Edges are not

evenly aligned.

Top and bottom rolls of

film are not matched

properly.

Press and hold the RUN button to manually advance the film. After 5

inches (125 mm). Grasp the film exiting the laminator and hold it Taut

while closing the laminator door.

Documents are

skewed in the film

when exiting

Documents fed in skewed

Before loading paper, try tapping the leading edge of the paper on a flat

surface and then repeat with the bottom or top edge to get your paper

properly squared.

Insert your media in the auto feeder and slide the edge guide up to edge

of your media.

Experiencing

frequent double

feeds

Paper has heavy static

Try fanning the media or placing in a paper jogger prior to feeding it. If

issues persist use the Manual Feed / Auto Cut mode.

Experiencing

frequent mis-feeds

Rollers are slipping on

media and do not feed

sheets

Try fanning the media or placing in a paper jogger prior to feeding it. If

issues persist use the Manual Feed / Auto Cut mode.

Andere Handbücher für FOTON 30 Automated Laminator

Andere GBC Laminiergerät Handbücher

GBC

GBC Arctic Titan 1040WFC Bedienungsanleitung

GBC

GBC 620OS Bedienungsanleitung

GBC

GBC fusion 1100L Anleitung zur Verwendung

GBC

GBC DELTA Bedienungsanleitung

GBC

GBC ORCA-I Bedienungsanleitung

GBC

GBC Fusion Plus 7000 L Bedienungsanleitung

GBC

GBC 5031TS ROLL Bedienungsanleitung

GBC

GBC TRIAD A3 Bedienungsanleitung

GBC

GBC FUSION 3000L Bedienungsanleitung

GBC

GBC DocuSeal 120 Bedienungsanleitung

GBC

GBC HeatSeal H425 Bedienungsanleitung

GBC

GBC fusion 1100L Bedienungsanleitung

GBC

GBC Arctic Titan 165 Bedienungsanleitung

GBC

GBC FUSION 7000L Bedienungsanleitung

GBC

GBC VOYAGER Bedienungsanleitung

GBC

GBC 6250 Bedienungsanleitung

GBC

GBC Discovery 50 Bedienungsanleitung

GBC

GBC H320 Bedienungsanleitung

GBC

GBC DocuSeal 40P Bedienungsanleitung

GBC

GBC Fusion Plus 6000 L Bedienungsanleitung

GBC

GBC PRO 3600 Bedienungsanleitung

GBC

GBC Fusion Bedienungsanleitung

GBC

GBC DOCUSEAL 1200 Bedienungsanleitung

GBC

GBC ORCA III T Handbuch

Beliebte Laminiergerät Handbücher anderer Marken

Renz

Renz HT 330 L Bedienungsanleitung

Gfp

Gfp 44TH Bedienungsanleitung

Lapis

Lapis Lamina006 Bedienungsanleitung

Hama

Hama L44B Bedienungsanleitung

PAVO

PAVO FLORIDA Bedienungsanleitung

M-Triangel

M-Triangel MT-102 Bedienungsanleitung

Akiles

Akiles PROLAM 230 Bedienungsanleitung

D&K

D&K Masterpiece 550 Bedienungsanleitung

Falcon

Falcon F-40 Bedienungsanleitung

LEITZ

LEITZ EasyLaminator A4 Bedienungsanleitung

LEITZ

LEITZ coldLAM CS9 Bedienungsanleitung

kala

kala Starter 1080 Bedienungsanleitung

Fellowes

Fellowes Venus A3 Bedienungsanleitung

Qomolangma

Qomolangma FMJ-1400-WA-PLUS Bedienungsanleitung

Opus

Opus Coverator 330 Bedienungsanleitung

ALDI

ALDI OL 250-L Bedienungsanleitung

Phoenix

Phoenix 2700-DH Bedienungsanleitung

acropaq

acropaq AL-3400 Bedienungsanleitung