GBC Auto+ 100M Bedienungsanleitung

S H R E D D E R S

A U T O + 500X&500M™

Instruction Manual

www.accobrandsasia.com

min

Sheet capacity:

Manual feed slot

10 sheets (80gsm)

Sheet capacity:

Autofeed chamber

500 sheets (80gsm)

Duty Cycle Continuous

Run time from cold Continuous

Volts / Hz UK Version: 230V / 50Hz

Amperage UK Version: 1.2 Amps

Motor Watts UK Version: 270 Watts

Sheet capacity:

Manual feed slot

9 sheets (80gsm)

Sheet capacity:

Autofeed chamber

500 sheets (80gsm)

Duty Cycle Continuous

Run time from cold Continuous

Volts / Hz UK Version: 230V / 50Hz

EK Version: 220V / 60Hz

Amperage UK Version: 1.7 Amps

EK Version: 1.7 Amps

Motor Watts UK Version: 390 Watts

EK Version: 400 Watts

technical specifications

GBC Auto+ 500X GBC Auto+ 500M

To guard against injury, the following basic safety precautions must be observed in the set-up of this

product.

• Ensure the machine is plugged into an easily accessible power outlet, and ensure the cable is not

likely to trip up a passer by.

•

supplier.

• Unplug your shredder before moving it or when it is not in use for an extended period of time.

• Do NOT operate with a damaged power supply cord or plug, after it malfunctions, or after it has

been damaged in any manner.

•

• The socket-outlet should be near the equipment and should be easily accessible.

•

• Do NOT use near water.

• Do NOT use aerosol dusters or cleaners.

• Do NOT spray anything into the shredder.

• Do NOT load the auto-feed chamber with unopened junk mail, magazines, bound documents etc.

Although this shredder has been designed to comply with UL 60950-1 EN 60950-1 safety standards

including the “probe accessibility tests”, do not operate the shredder near children or pets.

autofeed technology

points to note

The Auto+ 500X and 500M has been designed to automatically shred up to 500 sheets from the

auto-feed chamber and up to 9/10 sheets through the manual feed slot. The auto-feed mechanism

has been designed to handle paper fastened with staples and paper clips and to only pull a few

sheets of paper into the cutting mechanism to minimise the risk of paper jams.

A U T O + 500X&500M™S H R E D D E R S 5

control panel and indicators

Jam Free indicator – This alerts

the user when too much paper is

fed into the manual feed slot (see

section on Jam Free Technology).

Paper Loading Door/Bin Door

Open or Bin Full indicator –

This means either:

• Loading door is open

• Bin is open

• Bin is full

Lock indicator – This means the

paper loading door is locked (during

shredding).

Oil Refill indicator

Oiling in Operation indicator

Paper jam indicator – This means

there is a paper jam in the auto feed

chamber.

If this symbol is flashing the

shredder is attempting to clear a

paper jam automatically.

If this symbol is permanently

illuminated red please follow the

instructions under ‘Reverse function’

to clear any jammed material.

Continuous Jam Boost

Auto

Reverse

Loading Door Locking

Mechanism – PIN Password

Buttons – Enter a four digit code

to lock the loading door during

shredding.

warning symbols

Sheet capacity of manual feed

entry slot.

This means no aerosols.

This means keep children away

from shredder.

This means you should be careful

because long hair can become

entangled in the cutting head.

This means don’t reach into the

feed opening of the cutting head.

This means be careful of loose

jewellery which could become

entangeld in the cutting head.

This means no oil lubrication,

use Rexel oil sheets only.

This means be careful of ties and

other loose clothing which could

become entangled in the cutting

head.

This means the shredder can

accept small paperclips.

This means the shredder can

accept small staples.

Safety First

Auto+ 500X/500M shredding capability

Auto+ 500X/500M CAN shred the following:

• 500 sheets

• Stapled paper, 25mm within the corner

• 26/6 and 24/6 or smaller staples

• Small sized paper loaded centrally

• 500 sheets

• Paper clip paper, 25mm within the corner (500X through manual feed slot ONLY)

• Capable of shredding small/medium paper clips (max. wire thickness = 0.9 mm)

• >80/100gsm paper (through manual feed slot ONLY)

• A3 folded in half max. 2 sheets

• 500 sheets

• 80 gsm paper

- A4 - 210mm x 297mm

- A5 - 148mm x 210mm

- A3 single sheet folded in half to make A4

Auto+ 500X/500M CAN shred (through the manual feed slot):

Thick paper or

card.

Multiple folded

sheets (e.g. A3

sheets folded in

half).

Unopened mail

(e.g. junk mail).

Glossy paper or

a sheet covered

with print on both

sides.

Auto+ 500X/500M CANNOT shred the following:

Large clips.

Check the length

of the paperclip

is not longer than

32mm.

Heavy duty

staples. Check

the staple leg

length is not

greater than

6mm.

Bound

documents

Bulldog clips

Magazines or

other documents

bound by multiple

staples or clips.

Adhesive labels.

Plastic sheets,

laminated

documents,

plastic folders.

A U T O + 500X&500M™S H R E D D E R S 7

intelligent help

1In the unlikely event of the shredder jamming, the Auto+ 500X & 500M will stop shredding,

and the jam icon will blink in orange.

2The shredder will illuminate the FWD ( ) and REV ( ) buttons in the sequence necessary

to clear the jam.

3If the jam cannot be intelligentally cleared, the jam icon ( ) will illuminate in red. At this

point follow the reverse function instructions to clear any jammed material.

automatic jam clearance

Intelligent Jam Clearance: In the unlikely event of the shredder jamming, the Auto+ 500X and 500M

will automatically reverse and forward the engine three times to clear a jam. During this operation

the Paper Jam indicator will flash ( ).

The shredder is designed to automatically lubricate the cutting mechanism as required to ensure

the product continues to work to its maximum performance and to extend the product life. Please

follow the operation instruction before turning on the shredder for the first time. The 60ml bottle

of oil* is sufficient to allow the shredder to start for the first time and to operate continuously for

about one hours shredding before the reservoir will need refilling. When the ‘Oil Refill’ indicator is

illuminated ( ), flip up the oil reservoir cap and refill the oil reservoir using a bottle of standard

GBC oil (1760049)*. The automatic oiling operation ( ) last approximately two seconds and

you will hear the distribution pump during this time. Auto-oiling operates after 15 minutes of

shredding time.

auto-oiling technology

bin or loading door open safety function

As a safety precaution, if the bin or loading door is opened during shredding, the shredder will stop

and the bin full indicator will illuminate ( ).

jam free technology in manual feed slot

Sensors in the paper feed area measure the thickness of paper about to be shredded. The

ability to shred or not is communicated through red and green lighting. Green means that the

stack of paper is within the shredders sheet capacity and OK to shred. Red means that you

have too much paper, remove some sheets in order to shred.

Given that you are unable to shred more sheets of paper than the shredder is capable of

shredding, paper jams are prevented.

This prevents wasting time reversing paper and unblocking jams not to mention the mess it

can create.

* ACCO Brands accepts no liability for product performance or safety when other types or brands of lubricants are used on

any part(s) of this machine.

Reverse the paper out then turn the machine off using the ON/OFF switch at the rear of the

If there is paper in the Autofeed chamber after first attempt, open and re-close the paper loading

door a second time.

Check that the on/off switch at the back of the machine is switched to the ‘ON’ position.

Do not fill above the MAX level, this could damage the shredder.

system. Only required when the product is used for the first time.

1. initial setup

1After unpacking the product pull out the shredder bag frame and remove the CD shard tray,

which sits on top of the bag frame. Store this tray on the product as shown and use when you

shred CDs.

Lift up the loading door and open oil flap.

Remove oil cap and fill up the reservoir using the 60ml bottle of oil provided. Replace the cap.

4Connect the shredder to mains supply.

6Press and hold down the Auto button ( ) for 5 seconds to start the pump and prime the

1Check that the on/off switch at the back of the machine is swtiched to the ‘ON’ position.

To commence shredding, press the auto feed button. This sets the shredder into auto mode.

2. operation

2To load the shredder, simply lift the loading door handle to open the loading door and insert

documents.You can open the door further to 90 degrees for easier access if required Load up to

500 sheets at a time into the feed chamber.

3The shredder will start the shredding cycle automatically ONLY after closing the loading door.

Attention: If required you can now lock the loading door by entering a 4 digit code (see Locking

the Paper Loading Door section).

4If you only have up to 9/10 sheets to shred, you can use the manual feed slot, provided the auto

feed chamber is empty.

5Insert paper to be shredded into the feed area.The shredder will detect the paper and start

automatically.

6If the shredder is left in auto mode for more than 2 minutes without being used, the shredder will

automatically turn back to sleep mode in order to save power.

7The shredder will automatically ‘wake up’ from sleep mode when paper is inserted into the

shred mouth or you open the loading door. There is no need to press the Auto button ( ).

3. reverse function

1Should you wish to reverse paper out whilst shredding, a reverse button ( ) has been fitted for

your convenience.

shredder. Remove the paper from the manual feed slot (if being used) or open the loading door,

remove the remaining stack of paper, then pull the jammed paper free of the cutting mechanism.

3To resume shredding, turn the shredder on using the ON/OFF switch at the rear of the shredder.

Return the switch to the auto position ( ).

A U T O + 500X&500M™S H R E D D E R S 9

For additional security the paper loading door can be locked during the shredding of confidential

material.

GBC encourages customers to recycle shredded paper.

Please note that shredded paper cannot be recycled if mixed with credit card shards.

If recycling, please separate shredded paper and credit cards.

4. locking the paper loading door

To lock shredder:

Place documents in tray. Close paper loading door.

Press any 4 digits. REMEMBER YOUR CODE!

Shredder unlocks automatically when:

• 4 digit code is re-entered.

• Shredding is complete.

• Shredder is inactive for 30 minutes (but documents remain in tray)

7. bin full

The shredder will not function when the bin is full and the bin full symbol ( ) is illuminated.

You should empty the bin.

• Open the door and slide out the waste sack support frame.

• Carefully remove the waste sack from the frame.

5. CD/DVD shredding

A separate CD/DVD tray is provided to collect the shredded CD/DVD shards. Ensure that this is

correctly mounted onto the standard shredder bag frame before shredding.

1Lift up the paper loading door.

2Always insert CDs/DVDs in the CD/DVD slot. Only shred one CD/DVD at a time.

3Close the paper loading door.

4Empty the CD/DVD bin after 8 CDs/DVDs to avoid waste spilling over into the paper waste bin.

5Remove the CDs/DVDs tray before recommencing to shred paper and store on the side of the

shredder.

6. credit card shredding

The Auto+ 500X and 500M can shred credit cards. Switch the shredder to auto mode, then;

1Lift up the paper loading door.

2Insert the credit card into the roller as shown. Only shred one credit card at a time.

3Close the paper loading door.

Andere Handbücher für Auto+ 100M

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere GBC Aktenvernichter Handbücher

GBC

GBC ShredMaster 950S Bedienungsanleitung

GBC

GBC 3870M-2 Bedienungsanleitung

GBC

GBC SHREDMASTER SM15-08 Bedienungsanleitung

GBC

GBC Shredmaster 5570X Handbuch

GBC

GBC 3500S-2 Bedienungsanleitung

GBC

GBC CX25-36 Bedienungsanleitung

GBC

GBC Shredmaster 1130S Bedienungsanleitung

GBC

GBC Shredmaster 1036S-2 Bedienungsanleitung

GBC

GBC GBC Shredmaster 75X Handbuch

GBC

GBC Shredmaster 3270M Bedienungsanleitung

GBC

GBC ShredMaster GDHS7 Bedienungsanleitung

GBC

GBC ShredMaster GLS3230 Bedienungsanleitung

GBC

GBC SHREDMASTER PX12-06 Bedienungsanleitung

GBC

GBC ShredMaster Jam Free Series Bedienungsanleitung

GBC

GBC Auto+200M Bedienungsanleitung

GBC

GBC Shredmaster 7550X Bedienungsanleitung

GBC

GBC Style Bedienungsanleitung

GBC

GBC Alpha Ribbon Bedienungsanleitung

GBC

GBC Shredmaster 5160X Bedienungsanleitung

GBC

GBC ShredMaster CC055 Bedienungsanleitung

GBC

GBC SHREDMASTER 1246S-2 Bedienungsanleitung

GBC

GBC CX40-59 Bedienungsanleitung

GBC

GBC 6550X-2 Bedienungsanleitung

GBC

GBC Shredmaster 55X Handbuch

Beliebte Aktenvernichter Handbücher anderer Marken

Swingline

Swingline STACK-AND-SHRED200X&200XL 60X Bedienungsanleitung

UNITED OFFICE

UNITED OFFICE UAV 190 A1 Bedienungsanleitung

UNITED OFFICE

UNITED OFFICE UAV 190 A1 Bedienungsanleitung

Rexel

Rexel Optimum AutoFeed+ 45X Bedienungsanleitung

Martin Yale

Martin Yale 227284S1 Bedienungsanleitung

Bonsaii

Bonsaii DocShred C223-A Bedienungsanleitung

HSM

HSM Pure 740 max Bedienungsanleitung

TRU RED

TRU RED TR-BMC20A Bedienungsanleitung

Fellowes

Fellowes 50S Bedienungsanleitung

Gude

Gude GH 2600 P Bedienungsanleitung

Ativa

Ativa DQ80M Bedienungsanleitung

Q-Connect

Q-Connect Q8CC Bedienungsanleitung

Fellowes

Fellowes POWERSHRED C-325CI Bedienungsanleitung

Olivetti

Olivetti Privacy 5000C Kurzanleitung

UNITED OFFICE

UNITED OFFICE UAV 190 A1 Bedienungsanleitung

Dahle

Dahle paperSAFE 22022 Bedienungsanleitung

Formax

Formax OnSite FD 87 Bedienungsanleitung

GEHA

GEHA Home & Office S7 CD Bedienungsanleitung