GCC Technologies PII-132S Bedienungsanleitung

Puma II users manual

Contents

Important information …………………………………………..…….. I

Quick installation guide ………………………………………….…… II

About cutting tool ………………………………………….…………. III

Checking Supplied items …………………………………….……….. IV

Chapter 1. Parts Names and Functions ………………………….……. 1-1

1.1 Front view …………………………………………………… 1-1

1.2 Back view with stand ………………………………… …….. 1-2

1.3 Side view …………………………………………………….. 1-3

1.4 Control Panel ………………………………………………… 1-4

Chapter 2. Setup …………………………………….………………… 2-1

2.1 Setting up …………………………………………………….. 2-1

2.2 Stands and media support system installation……………….. 2-2

2.3 Power and cable connections ………………………………… 2-5

2.4 Blade installation ……………………………………………. 2-6

2.5 Media loading ……………………………………………….. 2-9

2.6 Tracking performance ……………………………………….. 2-15

2.7 Dip switch setting ……………………………………………. 2-16

2.8 Power on …………………………………………………….. 2-18

2.9 On/Off line key ……………………………………………… 2-19

2.10 Pause key …………………………………………………… 2-19

2.11 Repeat key ………………………………………………….. 2-19

2.12 Data clear key ………………………………………………. 2-20

2.13 Origin setting ………………………………………………. 2-20

2.14 Cut test ……………………………………………………… 2-21

2.15 When completing the cutting job …………………………… 2-23

Chapter 3 Connecting cutting plotter …………………………………. 3-1

3.1 Universal serial bus ………………………………………… 3-1

3.2 Parallel transmission ……………………………………….. 3-2

3.3 Serial transmission …………………………………………. 3-2

Chapter 4 Virtual LCD ………………………………………………… 4-1

4.1 Installation ………………………………………………….. 4-1

4.2 Before usingVLCD …………………………………………. 4-1

4.3 Functions of VLCD ……………………………………………. 4-2

Chapter 5 Basic Maintenance ………………………………………… 5-1

Puma II users manual

5.1 Cleaning the cutting plotter ………………………………… 5-1

5.2 Clearning the grid drum…………………………………….. 5-1

5.3 Clearning the pinch rollers …………………………………. 5-2

Chapter 6 Troubleshooting ………………………………………….… 6-1

6.1 If the cutting plotter cannot operate ………………………… 6-1

6.2 Light indicators …………………………………………….. 6-1

6.3 Cutting quality problem…………………………………….. 6-5

Appendix:

1. Specifications of Puma II ………………………………………….. a

2. Specifications of GCC blade ………………………………………. b

Puma II users manual

IMPORTANT INFORMATION

Thanks for your purchasing of our SignPal Puma II series cutting plotters.

For your safety and optimize the performance of the Puma II, please read

user manual completely and keep it in a correct location.

PRECAUTIONS IN USE

 For safety’s sake, please always hold the cutter firmly from the bottom when

moving it. Please hold from the bottom.

 Do not shake or drop the blade holder, blade tip maybe fly out.

 During operation, keep away from any moving parts of the cutter (such as the

carriage, drums). Also be careful that clothing and hair do not be caught.

 Connect the power cable to a grounded outlet.

 Always use the accessory power cable that is provided. Do not wire the power

cable so that it becomes bent or caught between objects.

 Do not connect the power cable to branch outlet to which other machines are also

connected, or use an extension cable. There is danger of overheating and of

mis-operation of the machine.

 Keep the blade away from children.

 Always put the pinch rollers within position of the white marks.

QUICK MENU

1. Power ON. (The POWER LED lights on)

2. Note: Make sure the level is up before placing the media on the plotter. Place the

media and pull the level to lower down the pinch rollers (must be sure the pinch

rollers are position above the grid drums, that is, within the white marks).

3. Puma II will take about 10 sec to initialize the machine. Then the

cutter will size the media automatically according to set of the dip switch (usually

the presetting is EDGE media type).

4. Off-line condition – Plotter is not ready to receive data from computer. Press

ON/OFF LINE key, the LED above the key turns off.

5. On-line condition - Plotter is ready to receive data from computer. Press

ON/OFF LINE key, the LED above the key lights.

6. Change the setting value during cutting. Press PAUSE key, the LED above the

key flashes. To continue cutting press ON/OFF LINE key.

7. Terminate the cutting and clear the data in the buffer. Press ON/OFF LINE key or

PAUSE key and then press DATA CLEAR key.

About the Tool

A generic term refer to the blade that cuts the sheet, the pen that does plotting, and

the LED bombsight (option) used for pointing to the reference point.

OFFSET is the distance that the blade tip is displaced from the centerline of the

blade.

Protrusion Length of the Blade

Length of protrusion = t1 + t 2/ 2, but for your convenience you may just make it about 0.3~ 0.5

mm beyond the blade holder tip.

Blade

Central line

Blade tip

Offset

Thickness of

the film (t1)

Thickness of the

base paper (t 2)

Protrusion length

of the blade

Checking Supplied Items

1. Installation CD 2. Printer Cable 3. AC Power Cable

4. RS232 Cable 5. Blade Holder & Fiber –

Tip Pen

6. Cutting Strip (Pad)

7. Safe Blade 8. USB Cable 9. Error-Correct & Function

Sticker

10 Roll Base

(only for PII-30/60)

11. Tweezers 12.Knife

PumaIIUsersmanual IV

Chapter 1 Parts Names and Functions

1.1 Front View

Platen: The surface fo

holding and supporting

media during cutting.

Cutting Pad: Provides

protection for the blade

while the blade is cutting

Alignment Ruler: Media

can be aligned with the

clear guide line marks

Cutting Carriage: This

unit performs the cutting

with the installed blade and

pen.

Grid Drum: Moves the

media back and forth

during operation.

Control Panel: Consists of

10 control keys and 6 LEDs

Knife Guide: To cut of

the extra media easily

along this groove.

Pinch Roller: Press the

media against grid drum

during cutting.

Paper

Sensor: The

Sensor detect

the presence

of media.

Figure 1-1 Front view of Puma II

PumaIIusersmanual 1-1

1-2 Back View of Puma II 132S with stand

Roll holder support

Roll Holder guide bushes

Stand

Roll holder

Fig 1-2 Back view of Puma II 132S with stand

PumaIIusersmanual 1-2

1-3 side view of Puma II

1 2 3 4 5 6 7 8

Fig 1-3 Left hand side view of Puma II Fig 1-4 Right hand side view of Puma II

Left Hand Side (Figure 1-3)

1. AC Power Connector – Used to insert the AC power cord.

2. Fuse – Up to 3 Amp.

3. Power Switch – On when switches to [I]; Off when switches to [O]

Right Hand Side (Figure 1-4)

4. USB interface Connector - Used to connect the cutting plotter to a

computer through a USB cable.

5. Parallel Interface Connector (Centronics) – Used to connect the cutting

plotter to a computer through a parallel interface cable.

6. Pen Force Control Slider – Set the blade force here.

7. Serial Interface Connector (RS-232C) – Used to connect the cutting

plotter to a computer through a serial interface cable.

8. Dip Switch - Used for various parameter setting.

PumaIIusersmanual 1-3

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere GCC Technologies Cutter Handbücher

GCC Technologies

GCC Technologies LaserPro Mercury Bedienungsanleitung

GCC Technologies

GCC Technologies i-Craft Bedienungsanleitung

GCC Technologies

GCC Technologies LabelExpress Bedienungsanleitung

GCC Technologies

GCC Technologies Expert II Bedienungsanleitung

GCC Technologies

GCC Technologies Jaguar J5-61 Bedienungsanleitung

GCC Technologies

GCC Technologies LaserPro SmartCut X380 Series Bedienungsanleitung

GCC Technologies

GCC Technologies AFR-24S Bedienungsanleitung

GCC Technologies

GCC Technologies AFJ-24S Bedienungsanleitung

GCC Technologies

GCC Technologies LaserPro X252RX Bedienungsanleitung

Beliebte Cutter Handbücher anderer Marken

Milwaukee

Milwaukee HEAVY DUTY M12 FCOT Bedienungsanleitung

SignWarehouse.com

SignWarehouse.com Bobcat BA-60 Bedienungsanleitung

Makita

Makita 4112HS Bedienungsanleitung

GEISMAR STUMEC

GEISMAR STUMEC MTZ 350S Bedienungsanleitung

Hitachi

Hitachi CM 4SB2 Fehlerbehebungshandbuch

Dexter Laundry

Dexter Laundry 800ETC1-20030.1 Bedienungsanleitung

DeWalt

DeWalt XR LI-ION DCS350N Bedienungsanleitung

Baudat

Baudat ES1 Bedienungsanleitung

Mafell

Mafell ZAF 200 Leitfaden

Makita

Makita 4100NH Bedienungsanleitung

Formax

Formax FD 574 Bedienungsanleitung

EINHELL

EINHELL TE-MA 1500 Bedienungsanleitung

Husqvarna

Husqvarna Cut-n-Break K 760 Bedienungsanleitung

CLEAN ROOM DEVICES

CLEAN ROOM DEVICES CRD130SS Bedienungsanleitung

TRI tool

TRI tool 301A Bedienungsanleitung

Roller

Roller King 1 1/4 Bedienungsanleitung

RODCRAFT

RODCRAFT RC7170 Bedienungsanleitung

Guarda

Guarda EDGE Bedienungsanleitung