GE RAKUVC1 Bedienungsanleitung

31-5000582 Rev. 0 01-21 GEA

RAKUVC1 and RAKUVC2 kits are designed to work with Zoneline AZ45 and AZ65 models with an

engineering digit of 5 or greater.

Installation Instructions

for your new

RAKUVC1

RAKUVC2

PTAC UVC Kit

Before you begin - Read these instructions completely and carefully.

IMPORTANT – OBSERVE ALL GOVERNING CODES AND ORDINANCES.

Note to Installer – Be sure to leave these instructions with the Consumer.

Note to Consumer – Keep these instructions with your Owner’s Manual for future reference.

Parts Included

• Junction Box Assembly

• UVC Air Cutoff Assembly

• UVC Main Board Assembly

• UVC Wiring Harness

• Ground Wire

• Polybag with Screws

Tools Needed

• 5/16” Nut Driver

• 1/4” Nut Driver

•High Voltage discharge pliers

Installation Overview

GE is a trademark of the General Electric Company. Manufactured under trademark license.

Junction Box Assembly $LU&XWRႇ$VVHPEO\ Main Board Assembly

Wiring Harness

Installation Instructions

STEP 1:

Prepare Installation Area by Removing the Front Cover from Zoneline Unit

(if applicable)

WARNING 5LVNRI(OHFWULFDO6KRFNFDQFDXVHLQMXU\RUGHDWK%HIRUHVHUYLFLQJVZLWFKSRZHURႇDW

the service panel and lock the area to prevent power from being switched on accidentally.

Note: Record all Aux Mode settings before beginning this project.

1. Remove power from unit and remove the Front cover.

9HULI\89&FRPSDWDELOLW\E\FRQ¿UPLQJWKH37$&PRGHOQXPEHUVHHH[DPSOHEHORZ

&RQ¿UP\RXKDYHWKHFRUUHFW89&NLWIRU\RXUYROWDJHDSSOLFDWLRQ5$.89&95$.89&9

STEP 2:

Remove Vent Grille from Zoneline Unit

1. Remove and retain the four 5/16” screws securing the air louver. Note orientation of louver for replacement.

2. Remove louver and set aside.

5HPRYHDQGUHWDLQWKHZHOGHGZLUHJULGIURPWKHDLUGHÀHFWRUXVLQJDVPDOOÀDWEODGHGVFUHZGULYHU

Nomenclature Example

AZ45E09DABW5

Engineering Revision - Must be 5 or higher

Installation Instructions

STEP 4:

Remove Vent Trim from Zoneline Unit

1. Remove the 7 screws securing the vent trim using 5/16” driver. Retain screws and vent trim to reinstall later.

2Q9PRGHOVWKHYHQWWKHUPLVWRUZLOOEHSUHVHQWRQWKH9HQWWULP7KHYHQWWKHUPLVWRUZLUHVZLOOQHHGWREH

disconnected from the connector on the wiring harness.

STEP 3:

Remove Control Panel from Zoneline Unit

1. If applicable, remove and discard the existing junction box and screws.

2. Remove and retain the three 5/16” screws securing the control panel.

3. Unplug the power connection to the control panel and personality plugs.

DPSSRZHUFRUGVGRQRWKDYHDSHUVRQDOLW\SOXJ

4. Remove the control panel from the Zoneline unit and set aside. Remove and retain 3 screws

Junction Box

Remove and discard existing junction box, if present.

7KHUPLVWRU

wire connector

Installation Instructions

STEP 5:

5HPRYHWKH$LU&XWRႇ

1. Loosen the two screws that secure the left side fan blade support. Do not completely remove screws.

2. Gently pull outward on the left side fan blade support.

:KLOHJHQWO\SXOOLQJRQWKHIDQEODGHVXSSRUWSXOOWKHDLUFXWRႇWRZDUGWKHULJKW

5HPRYHWKHDLUFXWRႇDQGGLVFDUG,WZLOOEHUHSODFHGE\WKHQHZ89&DVVHPEO\

AIR CUTOFF

Installation Instructions

STEP 6:

,QVWDOOWKH89&$LU&XWRႇ$VVHPEO\

5HPRYHWKH89&$LU&XWRႇDVVHPEO\IURPWKHNLWSDFNDJLQJDQGLQVWDOOLWLQWRWKHXQLWZKHUHWKHROGDLUFXWRႇZDV

SODFHG5HSHDWWKHSUHYLRXVVWHSVLQUHYHUVHRUGHUWRLQVWDOOWKHFXWRႇ7KHULJKWHQGRIWKHDLUFXWRႇVKRXOGVOLSLQWR

the right fan blade support and the left end can be guided into the left fan blade support.

%HFDUHIXOQRWWRGDPDJHWKHLQGRRUFRLOZKHQLQVWDOOLQJWKHQHZ89&FXWRႇ7KH89&EUDFNHWZKLFKLVDWWDFKHGWR

WKHXQGHUVLGHRIWKH89&$LU&XWRႇVKRXOGEHSRVLWLRQHGMXVWEHKLQGWKHLQGRRUFRLO

7KHZLUHKDUQHVVVKRXOGEHUHWDLQHGWDXWDVLWZDVVKLSSHGXQGHUWKHDLUFXWRႇWRDYRLGLQFLGHQWDOFRQWDFWZLWKWKH

fan blade.

7LJKWHQWKHVFUHZVWKDWZHUHORRVHQHGRQWKHOHIWIDQEODGHVXSSRUWVLQ67(3

&DUHIXOO\VSLQWKHLQGRRUIDQEODGHWRPDNHVXUHWKDWQRWKLQJLVLQWHUIHULQJZLWKLWVPRWLRQ7KHIDQEODGHVKRXOGVSLQ

freely without any objectionable noises.

STEP 7:

Installation of the Vent Trim

3ODFHWKHYHQWWULPWKDWZDVUHPRYHGLQ67(3

2. Route the UVC wiring through the notch in the vent trim for the thermistor wires. On 265V models the UVC wiring

will share this opening with the thermistor wires. Make sure wires are not pinched.

3. Reinstall the seven 5/16” screws removed previously.

5HFRQQHFWWKHWKHUPLVWRUZLUHLISUHVHQWWRWKHZLULQJKDUQHVVIURP67(3

Use existing thermistor wire

path for UVC wiring harness

Installation Instructions

STEP 8:

Installation of the UVC Main Board

1. Disconnect the thermistor wire harness from the main board.

2. Remove the two screws at the top and bottom of the white main board cover using a 1/4” driver and save.

3. Remove the main board cover and set aside.

4. Disconnect the indoor fan motor connector.

5. Detach all electrical connectors from the front of the main board.

7KHPDLQERDUGLVVHFXUHGE\DZKLWHUHWDLQLQJSLQ6TXHH]HWKHFRQQHFWRUSURQJVXQWLOLWVOLGHVEDFNDQGUHOHDVHV

the main board.

7. Discharge possible stored energy from the capacitor using high voltage discharge pliers.

8. Unplug remaining connectors on the main board taking note of the connector locations. Connectors are color coded.

5HPRYHDQGGLVFDUGWKHPDLQERDUGIURPWKHFKDVVLV7KLVPDLQERDUGZLOOQRORQJHUEHXVHG

%HIRUHLQVWDOOLQJWKHQHZ89&PDLQERDUGUHIHUWRWKHPLQLPDQXDOIRULQVWUXFWLRQVRQKRZWRFRQ¿JXUHWKHVHWWLQJV

IRU\RXUVSHFL¿FPRGHO

11. Remove the new UVC main board from the kit packaging.

12. Reinstall terminals on the new UVC main board making sure black and brown wires are on their correct terminals.

1/4” screws White retaining pin

2341

ON CIT

2341

ON CIT

Service Board Set-Up

Switch Position Meaning Switch Setting Meaning

S2-1 OFF=heat pump

ON=air conditioner 6 Rႇ N%78

6 Rႇ

S2-2 %786HWWLQJV S2-2=on N%78

S2-3 %786HWWLQJV 6 Rႇ

S2-4 Make-up air module

¿WWHG

6 Rႇ N%78

S2-3=on

S3-1 +HDWSLSHRSWLRQ¿WWHG S2-2=on N%78

S3-2 OFF = 230/208V model

ON = 265V model S2-3=on

S3-3 Not used

S3-4 Not used

Installation Instructions

STEP 8 (cont):

Installation of the UVC Main Board

7DNHWKH9UHOD\ZLUHKDUQHVVIURPWKHNLWSDFNDJLQJ7KLVZLOOKDYHDQRUDQJHFRQQHFWRUZLWKUHGDQGZKLWH

ZLUHV&RQQHFWWKHZLULQJKDUQHVVRUDQJHFRQQHFWRUWRWKHQHZPDWLQJFRQQHFWRURQWKH89&PDLQERDUG

14. Route 240V relay wire harness down the left side of the main board.

15. Align the UVC main board and engage the white retaining pin to hold the main board in place.

16. Reconnect the indoor fan motor wiring harness connector.

17. Install the main board cover.

18. Secure the main board cover using the two 1/4” screws removed earlier.

19. Reconnect the thermistor wiring harness.

Wiring Harness

New orange UVC

VSHFL¿FWHUPLQDO

STEP 9:

Install the UVC Junction Box

1. Remove the junction box assembly from the kit packaging. On models that use wall plugs, the strain relief knockout

will need to be removed.

2. Install the large white connector from the new 240V relay harness to the matching side in the junction box.

,QVWDOOWKHVPDOOWZRZLUHZKLWHFRQQHFWRUWRWKHUHFWL¿HUERDUGORFDWHGLQWKHMXQFWLRQER[DVVHPEO\

4. Dress the 240V relay harness wiring by snapping the wire tie into the mating hole on the back left corner of the

junction box.

5HFWL¿HUERDUG

Holes for wire

KDUQHVV]LSWLH

STEP 9:

Install the UVC Junction Box

5. Install the junction box assembly to the Main board cover. Insert the top and bottom tabs on the backside of the

junction box into the corresponding slots on the front of the main board cover.

6. Install the 5/16” Hi-Lo screw into the mating hole to secure the junction box to the main board cover.

7. Attach the junction box cover and secure with black 5/16” screw provided with kit.

8. If a junction box was previously installed in this unit, reuse the ground wire and ground screw.

9. If there was not a junction box previously installed, then remove ground wire from kit packaging and attach one end

to the hole in the front top left corner of the junction box with green ground screw.

10. Attach the other end of the screw to an existing ground location on the end bracket of the indoor coil.

11. Attach the white UVC led connector to the corresponding connector on the top of the junction box.

Installation Instructions

Junction Box

Assembly

Ground wire

attachment

LED

Connector Attach the back

of the junction

ER[FRYHU¿UVW

9Printed in the United States

Installation Instructions

STEP 10:

Install the Control Panel and Vent Grille

1. Reinstall the black wire mesh to the vent trim by pressing it into place.

2. Reconnect the Control Panel wiring harness and reinstall Control Panel to the chassis.

3. Install the three 5/16” screws removed earlier to secure Control Panel.

4. Reinstall the Vent grille and secure it using the four 5/16” screws removed earlier.

STEP 11:

Enabling UVC Mode

1. Reconnect power and heater wire personality jumper.

7XUQRQSRZHUWRWKHXQLW

:KHQWKHXQLWLVLQ6723PRGHSUHVVWKHUHG$X[VHWEXWWRQORFDWHGDERYHWKHMXQFWLRQER[

4. Press the MODE button until a “ ” appears on the display.

5. Press the +/- keys to change the display to either “ ” for enable or “ ” for disable.

6. Press the Aux set button again to save and exit.

5HLQVWDOOWKH37$&)URQW&RYHU

Red

Aux Set

Button

31-5000582 Rev. 0 01-21 GEA

Les trousses RAKUVC1 et RAKUVC2 sont conçues pour utilisation avec les modèles Zoneline AZ45 et AZ65

avec le chiffre technique « 5 » ou supérieur.

Instructions d’installation pour

votre nouveau

RAKUVC1

RAKUVC2

PTAC UVC Kit

Avant de commencer - Lisez ces instructions attentivement et en entier.

IMPORTANT – OBSERVEZ TOUS LES CODES ET RÈGLEMENTS EN VIGUEUR.

Note à l’installateur – Assurez-vous de laisser ces instructions au consommateur.

Note au consommateur - Conservez ces instructions avec votre manuel d’utilisation pour consultation ultérieure.

Pièces incluses

• Boîte de jonction

• Volet d’arrêt d’air UVC

• Carte principale UVC

• Faisceau de fils UVC

• Fil de terre

• Sac de vis

Outils requis

• Tournevis à douille 5/16 po

• Tournevis à douille 1/4 po

• Pince de décharge de haute tension

Aperçu de l’installation

GE est une marque de commerce de General Electric Company. Fabriqué sous licence de marque.

Boîte de jonction Volet d’arrêt d’air Carte principale

)DLVFHDXGH¿OV

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere GE Zubehör für Klimaanlagen Handbücher

GE RAB26A Bedienungsanleitung

GE RAG60 Bedienungsanleitung

GE RAB24 Bedienungsanleitung

GE RAK4002D Bedienungsanleitung

GE 49218 Handbuch

GE RAK204U Bedienungsanleitung

GE RAB-71 Bedienungsanleitung

GE RAB71B Standard Bedienungsanleitung

GE RAK44 Bedienungsanleitung

GE RAB46B Bedienungsanleitung

GE RAD10 Bedienungsanleitung

GE RAB81 Bedienungsanleitung

GE VERTICAL ZONELINE 2010 Handbuch

GE RAK4002C Bedienungsanleitung

GE RAB46 Bedienungsanleitung

Beliebte Zubehör für Klimaanlagen Handbücher anderer Marken

Unitary products group

Unitary products group 2CE Series Bedienungsanleitung

Qlima

Qlima EU-ODZ104 Bedienungsanleitung

EMI

EMI 550000565 Bedienungsanleitung

ActronAir

ActronAir MRE-035AS Bedienungsanleitung

Mitsubishi Electric

Mitsubishi Electric RCN-K-E Bedienungsanleitung

Tecnosystemi

Tecnosystemi smart clima INFINITY BLUE RIVER Bedienungsanleitung

EINHELL

EINHELL Hot Air Stop Bedienungsanleitung

ActronAir

ActronAir ERQ2-16AS Bedienungsanleitung

Sharp

Sharp AZ-F900E Bedienungsanleitung

Danby

Danby DPSL120B1W Bedienungsanleitung

INABA DENKO

INABA DENKO DSH-UP20E20E-07 Bedienungsanleitung

ActronAir

ActronAir LM7-2W Bedienungsanleitung

Bard

Bard WGEIFM-3C Bedienungsanleitung

Toro

Toro LT3240 Bedienungsanleitung

Johnson Controls

Johnson Controls PD-75A Bedienungsanleitung

Trane

Trane BAYECON104AA Montageanleitung

Fujitsu

Fujitsu UTZ-KXGC Bedienungsanleitung

INABA DENKO

INABA DENKO TK Series Bedienungsanleitung