GE AU 29878 Bedienungsanleitung

AU/NZ 29878

Digital Answering Machine

User Guide

We bring good things to life

Getting started

Thank you for purchasing your new GE digital answering machine.

Please record the following for your future reference:

Serial Number: ____________________________

(found on the bottom of the unit)

Name of store: ____________________________

Date of purchase: __________________________

Attach or keep your receipt to assist with any repair under warranty. This product is

warranted for a period of 12 months from the date of purchase.

Package contents

For Australia only

• Answerer

• AC Adapter • Telephone Plug

Adapter

For New Zealand only

• Answerer

• AC Adapter • Telephone Plug

Adapter

Battery Back-up installation

In the event of a power loss, a 9-volt alkaline battery (not included) will enable the

answerer to retain messages stored in memory. To install a battery:

1. Remove the battery compartment door in the bottom of the unit by loosening

the screw with a Phillips screwdriver. Lift the door.

2. Connect a new 9-volt alkaline battery. The large and small contacts on the

battery clip and the battery will interlock. Once connected, place the battery

inside the battery compartment.

3. Replace the battery compartment door and tighten the screw.

Note: If the battery is low or not installed the unit announces “low

battery” at the end of your messages.

Installation

1. Plug the telephone line cord from the back of the answerer into the telephone

line socket.

2. Connect the telephone line cord from your telephone into the socket marked

PHONE in the back of the answerer. (You don’t have to connect your

telephone in order for the answerer to record incoming messages.)

3. Connect the plug of the power supply into the POWER 9V AC socket in the

back of the answerer. Plug the other end into an AC Power outlet.

The unit plays a long beep and announces “please wait” After the pause; the

unit beeps again and is ready for setup or to answer calls with the default

greeting and settings.

(See page 4 for a diagram of the connections)

Connections

ustralia

Power Outlet

New Zealand

Line Socket

Controls and functions

Recording a greeting

When recording the greeting you should be about 20cms from the unit. Eliminate as

much background noise as possible. The default greeting is “Record after tone”.

1. Prepare your greeting.

Sample greeting: “Hi, this is (use your name here). I can’t answer the phone right

now, so please leave your name, number, and a brief message after the tone,

and I’ll get back to you. Thank you.”

2. Hold down the [GREETING] button. After the tone, you have 30 seconds to

record your greeting.

3. Release the [GREETING] button when you finish. The greeting will playback

automatically.

Note: Your recording time must not be less than 2 seconds,

otherwise the unit will revert back to the default greeting.

Setting the day and time

The day and time is played automatically after each message. To set the day and

time:

DAY

1. Press and hold the [STOP/SET] button for two seconds, then release. The unit

anounces, “Time (the current day setting) To set day, press next…press set to

continue”

2. To change the day, press and release quickly the [NEXT] or [PREVIOUS] button

until the desired setting is announced.

3. To store the day, press and release the [STOP/SET] button. The unit confirms

the setting and enters the Hour menu.

HOUR

1. The unit announces, “(the current hour setting) To set hour, press next… press

set to continue.”

2. To change the hour, press and release the [NEXT] or [PREVIOUS] button until

the desired setting is announced.

3. To store the hour, press and release the [STOP/SET] button. The unit confirms

the setting and enters the Minutes menu.

MINUTES

1. The unit announces, “(the current minutes setting) To set minute, press next…

press set to continue.”

2. To change the minutes, press and release the [NEXT] or [PREVIOUS] button

until the desired setting is announced.

3. To store the minutes, press and release the [STOP/SET] button. The unit

confirms the setting and enters the Rings to answer menu.

Setting the Rings to Answer

This setting allows you to select the number of rings before the unit answers a call.

The default setting is 4.

1. The unit announces, “Ring to answer (the current ring to answer setting) To set

ring, press next… press set to continue.”

2. To change the ring to answer, press and release the [NEXT] or [PREVIOUS]

button until the desired setting is announced.

(Available options are 2, 4 or Toll Saver)

3. To store the number of rings to answer, press and release the [STOP/SET]

button. The unit confirms the setting and enters the Security Code menu.

Toll Saver

The toll saver allows you to save the cost of making a call when you are accessing

your messages remotely.

• If you have new messages, the unit will answer after the 2nd ring.

• If you have no new messages, the unit will answer after the 5th ring.

Therefore if you have no messages you can hang up after the 3rd ring and save the

cost of making a call.

Setting the security code

This setting allows you to change the security code used to access your answerer

from a remote location. The default setting is 123.

1. The unit announces, “Security code (the current code setting) To set security

code, press next… press set to continue.”

2. To change the first security code number, press and release the [NEXT] or

[PREVIOUS] button until the desired setting is announced. The unit announces

all three numbers, but only the first number will change.

3. To store the first number, press and release the [STOP/SET] button. A short

tone is heard.

4. To change the second and third number, follow steps 2 and 3 above. After the

third number is stored, the unit announces all the stored settings.

Reviewing the settings

This function allows you to review the current time, rings to answer, and security

code.

• Press and release the [STOP/SET] button to start the review. The unit

announces the current settings.

Adjusting the Volume

Use the [VOLUME] +and –buttons to increase or decrease the volume. Three quick

beeps are heard when the minimum and maximum levels are reached.

Message Indicator

The Message Indicator lets you know the status of the unit.

STATUS EXPLANATION

Message indicator flashes continuously. New messages have been received;

press [PLAY /MEMO] to hear your

messages.

Message indicator flashes rapidly. Memory is full. Erase one message.

Message indicator is on and not

flashing.

No action required, unit is ready to

receive calls.

Message indicator is off. Answerer is off. Press [ON/OFF] to turn

unit on.

Playing messages

When the message indicator flashes continuously you have received new

messages.

• To play messages, press and release the [PLAY/MEMO] button.

• To stop play, press and release the [STOP/SET] button.

• To restart the message, press and release the [PREVIOUS] button.

• To go back to the beginning of a previous message, press and release the

[PREVIOUS] button twice within one second.

• To skip the beginning of the next message, press and release the [NEXT]

button.

• To erase a message while it is playing, press and release the [ERASE] button.

The answerer announces, “Message Erased”.

Erasing all messages

When the answerer is not playing or recording, press and hold the [ERASE] button

until you hear, “Messages Erased”. If you do not have any messages,

the answerer will announce “Zero message”.

Leaving a memo

1. Press and hold the [PLAY/MEMO] button.

2. Record your message after the announcement and the beep are heard.

The maximum recording time for MEMO is 60 seconds.

3. Release the [PLAY/MEMO] button after you have finished talking. The unit treats

the memo as a message, and the MESSAGE indicator starts to flash.

Calls Screening

You can screen incoming calls by listening as the caller leaves a message and if you

want to talk to that caller, pick up any extension telephone.

The answerer will automatically stop the recording when you start talking.

Remote access

You can access your answerer from any touch-tone telephone by entering your

3-digit security code (the default security code is 123 – see Setting Security Code).

The remote function will not work with rotary or pulse dialling telephones. Also some

dialling telephones only output tones for a fraction of a second. If you experience

difficulty with remote access operation, try another telephone, or use a separate tone

generator.

Cut out the wallet-size remote access instruction card on page 11 for reference

during remote access.

To access your answerer remotely:

1. Call your telephone number.

2. After you hear the beep that follows the greeting, enter your 3-digit security

code. To by-pass the greeting, you can enter your security code any time while

the greeting is playing.

3. The unit plays the remote menu after the correct security code has been

entered. Menu selection can be made while the menu is playing.

Note:

The unit answers on the 10th ring if the unit is turned off or the memory is full.

To access the answerer, enter the 3-digit security code after the beeps. If the

memory is full, play your messages and erase some of them to restore memory. If

the answerer is off press 2 to turn it on.

After the unit plays the remote menu, it will wait 10 seconds for a command. If no

command is entered, the unit disconnects.

General Product Care

• You can clean your answering machine with a damp cloth. Do not use abrasives,

spray polish or solvents, which may cause permanent damage not covered by

warranty.

• Do not expose the product to extreme temperatures such as a hot radiator or

direct sunlight.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Beliebte Anrufbeantworter Handbücher anderer Marken

Radio Shack

Radio Shack TAD-795 Bedienungsanleitung

AT&T

AT&T 2455 Bedienungsanleitung

Panasonic

Panasonic KX-TG2583CB Bedienungsanleitung

Panasonic

Panasonic KX-TGE820E Bedienungsanleitung

BellSouth

BellSouth GH9488 Sicherheitsleitfaden

Panasonic

Panasonic KX-TG2631 Bedienungsanleitung

Panasonic

Panasonic KX-TCD961CXB Bedienungsanleitung

AT&T

AT&T 1717 Bedienungsanleitung

Alcatel

Alcatel TEMPORIS 55-CE Bedienungsanleitung

AT&T

AT&T E2562 Bedienungsanleitung

Telstra

Telstra Monitor 420 Bedienungsanleitung

Kortex

Kortex IAM V90 Bedienungsanleitung

Panasonic

Panasonic EASA-PHONE KX-T1451 Bedienungsanleitung

Philips

Philips VOIP8551B/05 Bedienungsanleitung

Topcom

Topcom LUCCA Answering Machine Bedienungsanleitung

Panasonic

Panasonic KX-TGM420 Bedienungsanleitung

Panasonic

Panasonic KX-TCD320E Bedienungsanleitung

TIPTEL

TIPTEL Ergophone 307 Bedienungsanleitung