GE EntelliGuard GBKRKR Bedienungsanleitung

Introduction

Key Interlock Kit:

The breaker key lock is an optional accessory,

which will keep the breaker in trip free state while

locked. Maximum 4 keys of Ronis/Profalux or Kirk

type can be used. All EntelliGuard Devices can be

equipped with one of the three locks, that when

fitted as indicated allow the use of one to four key

locks that lock the device in its open position.

Figure 1. (A) Front Cover

Devices are found in two Variants:

1. Factory mounted mechanism:

The breaker/device is supplied off works with all

cams and screws allowing the user to mount a

separately acquired GE type lock kit.

2. Field mountable device:

A kit is supplied allowing the field mounting of the

locking mechanism and allowing the use of a lock

of the correct type purchased elsewhere

Catalog Number:

Installation of kit

Use the following procedure to install the Key

Interlock Key accessory into the circuit breaker.

1. Turn the breaker off and discharge the closing

springs by depressing the OFF and ON buttons in

the sequence OFF-ON-OFF. Verify that the

breaker OFF-ON indicator shows OFF and that the

charge indicator shows DISCHARGE. If installing

in a draw-out type breaker remove breaker from

adaptor (cassette) before continuing.

Catalog No

Description

GBKRKR

Kirk Key Interlock kit

GBRONR

Ronis Interlock kit

GBPROR

Profalux Interlock kit

EntelliGuard ®G Circuit Breaker

Accessories

Key Interlock Kit Breaker Mounted

WARNING: Before installing any accessories, turn

the breaker OFF, disconnect it from all voltage

sources, and discharge the closing spings.

AVERTISSEMENT: Avant d’installer tout accessoire,

mettre le disjoncteur en position OFF, le

déconnecter de toute tension d’alimentation , et

décharger les resorts d’armement

DEH-41407 Installation Instructions

2. Loosen the 6 screws on front cover (fascia)

using a posidrive screw driver as shown in Fig 1.B

Rotate the charging handle down and slide the

front cover over the handle to remove the front

cover as shown in Fig. 1.C.

Figure 1. (B) Screw Removal (C) Handle Rotation

3. If the locking mechanism device has been

supplied factory fitted, remove the bracket and

cover from the EntelliGuard device. If supplied as

a field mountable kit, please proceed to step 4.

4. Take the Lock cover and carefully break out the

openings needed to place the required number of

locks

5. Fix each lock to the lock bracket using the

fixation nuts as indicated in Fig. 2

Figure 2.

6. Using the nut supplied with each lock fix the

activating CAM. Ensure that the CAM is positioned

as indicated in fig. 3. For Kirk Lock, insert the

spacer and fix the cam supplied with the Kit using

the screws provided in the lock.

Ronis lock

Profalux lock

Kirk lock

Figure 3.

7. Using the supplied screws fit the cover onto the

mechanism.

Spacer

8. Uninstall the Motor operator (Optional if

present), Grounding nut & Nylock nut as shown.

Fig 4.

Grounding nut Nylock nut

Figure 4.

9. Install adaptor nut and torque to 6Nm. Mount

the support bracket on grounding stud and

adaptor nut at other end. Secure support bracket

with hardware removed/provided. Torque to

6Nm. Fig 5

Install the Motor operator (if uninstalled) Refer

DEH41413 for Motor operator installation.

Support bracket Nylock nut Adaptor nut

Figure 5.

10. If the locking mechanism device has been

supplied factory fitted. Remount the mechanism

with its cover into the breaker, making sure that

the operating lever moves freely and interacts

correctly with the breaker mechanism. (Fig. 6)

Figure 6.

11. If supplied as a field mountable kit carefully

remove the dummy lock cover from the Breaker.

Mount the Lock mechanism with its cover into the

breaker, making sure that the operating lever

moves freely and interacts correctly with the

breaker mechanism. (See Fig. 7A, 7B, 7C).

Figure 7A.

Figure 7B. Tighten to 6 Nm (4.42ft-lbs)

Figure 7C.

Tighten to 6 Nm (4.42ft-lbs)

12. To reinstall the cover, rotate the charging

handle down and slide the front cover over the

handle to assemble the front cover to housing as

shown in Fig. 8.

14. Ensure the fascia is aligned properly with the

trip unit and the pad lock features of the breaker.

Figure 8.

15.Fasten the 6 mounting screws of fascia with

the housing using a pozidrive screwdriver. Apply

torque of 6 Nm (4.42ft-lbs).

Breaker key lock Operation:

Use the following procedure to operate the

padlock:

1. Depress the OFF pushbutton on the breaker

front Fascia and extend/pull the breaker padlock

lever to its' outer position.

2. With the padlock lever extended, rotate one or

more of the keys anticlockwise. The key can then

be removed thus locking the breaker in its open

position.

3. With padlock lever extended, insert the key and

rotate in clockwise to unlock.

GE Consumer & Industrial

Electrical Distribution

These instructions do not purport to cover all details or variations in equipment nor, to provide contingency to be met in connection

with installation, operation, or maintenance. Should further information be desired, or should particular problems arise which are not

covered sufficiently for the purchaser’s purposes, the matter should be referred to GE.

41 Woodford Ave, Plainville, CT 06062

www.geelectrical.com

DEH-41407 R02 (11/14)

Dieses Handbuch passt für folgende Modelle

Andere GE Schutzschalter Handbücher

GE Power Break II Bedienungsanleitung

GE MicroVersaTrip AKR-75 Bedienungsanleitung

GE ML-14-0 Bedienungsanleitung

GE AM-13.8-750-4C Bedienungsanleitung

GE AKR Series Konfigurationshandbuch

GE M-PACT Bedienungsanleitung

GE AM-2.4/4.16-100/150- 3 Bedienungsanleitung

GE Power Break II Bedienungsanleitung

GE Spectra Series AMC6FGB Bedienungsanleitung

GE AK-15 Bedienungsanleitung

GE AM-13.8-500-5C Bedienungsanleitung

GE AKR-30 Series Bedienungsanleitung

GE AM-4.16-250-6 Bedienungsanleitung

GE Power Break II Bedienungsanleitung

GE MicroVersaTrip Plus Bedienungsanleitung

GE AKR-5-100 Bedienungsanleitung

GE Magne-Blast AM-13.8-1000-3H Bedienungsanleitung

GE GL 310 F3/4031 P/VR Bedienungsanleitung

GE PowerVac GEK-86132G Bedienungsanleitung

GE AM-13.8-750-5 Bedienungsanleitung

GE EntelliGuard R7 Bedienungsanleitung

GE Spectra Series AMCB6FGB Bedienungsanleitung

GE AKR-30 Series Bedienungsanleitung

GE GE-200A Bedienungsanleitung

Beliebte Schutzschalter Handbücher anderer Marken

ABB

ABB SACE Emax 2 E2.2 Bedienungsanleitung

Eaton

Eaton NOVA LBS 15 Bedienungsanleitung

Gewiss

Gewiss 90 RCD Bedienungsanleitung

ABB

ABB SACE Emax E1 Bedienungsanleitung

Siemens

Siemens SIRIUS 3RV1742 Bedienungsanleitung

WEG

WEG FHU ACW125 Bedienungsanleitung

Siemens

Siemens Sentron 3VA9157-0PK1 Series Bedienungsanleitung

hager

hager TS 303 Montageanleitung

ETI

ETI EFI-4B Bedienungsanleitung

nader

nader NDM3EU-225 Bedienungsanleitung

TERASAKI

TERASAKI NHP TemBreak PRO P160 Series Bedienungsanleitung

Gladiator

Gladiator GCB150 Bedienungsanleitung

Eaton

Eaton 50DHP-VR Handbuch

ABB

ABB SACE Emax 2 E6.2 Handbuch

OEZ

OEZ LFN Bedienungsanleitung

Eaton

Eaton Power Defense PDG2 Handbuch

Bticino

Bticino L4412CM2 Bedienungsanleitung

Eaton

Eaton S-T0 Handbuch