GE KTD-400 Bedienungsanleitung

KTD-400 GE Security

KTD-400 Controller Keypad

User Manual

This document may not be copied or otherwise reproduced, in whole or in part, except as

specifically permitted under US and international copyright law, without the prior written

consent from GE.

Document number/ 1034790E (March 2006).

Disclaimer THE INFORMATION IN THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. GE ASSUMES

NO RESPONSIBILITY FOR INACCURACIES OR OMISSIONS AND SPECIFICALLY DISCLAIMS ANY

LIABILITIES, LOSSES, OR RISKS, PERSONAL OR OTHERWISE, INCURRED AS A CONSEQUENCE,

DIRECTLY OR INDIRECTLY, OF THE USE OR APPLICATION OF ANY OF THE CONTENTS OF THIS

DOCUMENT. FOR THE LATEST DOCUMENTATION, CONTACT YOUR LOCAL SUPPLIER OR VISIT US

ONLINE AT WWW.GESECURITY.COM.

This publication may contain examples of screen captures and reports used in daily operations.

Examples may include fictitious names of individuals and companies. Any similarity to names

and addresses of actual businesses or persons is entirely coincidental.

Trademarks and patents GE and the GE monogram are registered trademarks of General Electric.

Other trade names used in this document may be trademarks or registered trademarks of the

manufacturers or vendors of the respective products.

Intended use Use this product only for the purpose it was designed for; refer to the data sheet and user

documentation. For the latest product information, contact your local supplier or visit us online

at www.gesecurity.com.

FCC compliance This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio frequency energy and, if

not installed and used in accordance with the instruction manual, may cause harmful

interference to radio communications.

You are cautioned that any changes or modifications not expressly approved by the party

responsible for compliance could void the user's authority to operate the equipment.

iii

Contents

Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Conventions used in this document. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Safety terms and symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Product overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Controller keypad placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

DIP switch settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Mounting the KTD-300R. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Wiring connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Power-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

KTD-400 configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

System component configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

PTZ receiver configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Key layouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Key functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Keypad operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Multiplexer operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

VCR operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Contacting technical support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Online publication library . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

KTD-400 Controller Keypad

User Manual

Preface

This is the GE KTD-400 Controller Keypad User Manual for models KTD-400 and KTD-300R. This

document includes an overview of the product and detailed instructions explaining:

• how to install and program; and

• how to operate the KTD-400 and KTD-300R.

There is also information describing how to contact technical support if you have questions or concerns.

To use this document effectively, you should have the following minimum qualifications:

• a basic knowledge of CCTV systems and components; and

• a basic knowledge of electrical wiring and low-voltage electrical connections.

Read these instructions and all ancillary documentation entirely before installing or operating this product.

The most current versions of this and related documentation may be found on our website. Refer to Online

publication library on page 21 for instructions on accessing our online publication library.

Note: A qualified service person, complying with all applicable codes, should perform all required hardware installation.

Conventions used in this document

The following conventions are used in this document:

Safety terms and symbols

These terms may appear in this manual:

Bold Menu items and buttons.

Italic Emphasis of an instruction or point; special terms.

File names, path names, windows, panes, tabs, fields, variables, and other GUI elements.

Titles of books and various documents.

Blue italic (Electronic version.) Hyperlinks to cross-references, related topics, and URL addresses.

Monospace Text that displays on the computer screen.

Programming or coding sequences.

CAUTION: Cautions identify conditions or practices that may result in damage to the equipment or other property.

WARNING: Warnings identify conditions or practices that could result in equipment damage or serious personal injury.

KTD-400 Controller Keypad

User Manual

Product overview

The KTD-400 Controller Keypad is designed for use in a Digiplex system. The KTD-400 can address and

control 512 pan/tilt/zoom (PTZ) receiver sites, operate a matrix switcher with 64 monitor outputs, and address/

select views from as many as 64 multiplexers and VCRs. Several modes of multiplexers are supported.

Note: For CyberDome control with the KTD-400, pan/tilt operation is limited to three speeds. To operate and control

multiplexers and VCRs, you must have a KTD-93 auxiliary device driver attached to each device in a Digiplex system.

Controller keypad placement

A Digiplex system’s RS-422 control signal originates from the controller keypad located at the head of the

system and travels down line via twisted-pair cable. When more than one controller keypad is used, the signal

must loop through each keypad (Figure 1) or be merged using KTD-312 signal mergers (Figure 2) before

being routed to the rest of the components in the system.

Figure 1. Placement in a Digiplex system

Figure 2. Placement using a KTD-312 signal merger

RS-422

Multiplexer

Keypad Keypad

Video switcher

KTD-93

RS-422

Multiplexer

Keypad Keypad

Video switcher

KTD-93

KTD-312

Installation

To install a KTD-400 keypad, you will need to set the DIP switches, mount the unit (KTD-300R only), and

wire the device.

DIP switch settings

Use Tabl e 1 to select your mode of operation.

Figure 3 shows how to open the KTD-400 and KTD-300R and locate the DIP switches.

Figure 3. DIP switch locations for KTD-400 and KTD-300R models

CAUTION: Do not connect power to the unit before all installation steps have been completed. Do not connect directly to

a telecommunication network.

Table 1. DIP switch settings

Setting Binary Description

1000 Digiplex PTZ and VCR control only.

0100 Controlling a robot MV96 multiplexer with a KTD-93.

1100 Digiplex PTZ, multiplexer, and VCR control (factory setting).

0000 Controlling a robot MV96 multiplexer with a KTD-93.

KTD-400 KTD-300R

4-position

DIP switch

KTD-400 Controller Keypad

User Manual

Mounting the KTD-300R

The KTD-300R is designed to fit into a standard EIA 19-inch rack and uses one unit (1.75 in.) of rack space.

Mount the unit using the four holes in its front panel and hardware provided from the rack manufacturer.

Wiring connections

The KTD-400 comes with a 6 ft. (1.8 m) cable that attaches to a modular phone box (Figure 4). All external

connections are made in the phone box. KTD-300R connections are made to the removable terminal strip

located on the back of the unit (Figure 5 on page 4). Wiring the KTD-400 and 300R to control a standard

Digiplex system involves connecting the RS-422 input cable (if used), the RS-422 output cable, and the

12 VDC wall transformer.

Note: Figure 4, Figure 5, and Figure 6 on page 5 show connection points for an RS-422 input cable and an RS-422 output

cable. Do not confuse the two. The input is used only if other keypads, alarm chassis, or time/date generators are

located ahead of the unit that is being wired.

Figure 4. KTD-400 modular phone box connections for standard Digiplex control

Figure 5. KTD-300R terminal strip connections for standard Digiplex control

Keypad

Modular phone box

12 VDC wall

transformer

RS-422 control signal in

RS-422 control signal out

Color code

Y = Yellow

G = Green

BR = Brown

WH = White

R = Red

BL = Black

O = Orange

B = Blue

Terminal strip

RS-422 control signal in

RS-422 control signal out

12 VDC wall

transformer

KTD-300R keypad

KTS-41 system control

Wiring the KTD-300R to control a KTS-41A system involves connecting the RS-422 input cable (if used), the

RS-422 output cable (if used), the DTMF output cable (to the KTS-41A), and the 12 VDC wall transformer

(Figure 6).

Figure 6. KTD-300R connections with KTS-41A control

Power-up

After you make all the connections, the KTD-400 or KTD-300R will be ready for operation. Plug the 12 VDC

wall transformer into a power outlet. The LCD window will briefly display keypad setting information

(Figure 7 on page 6), then it will enter the operating mode.

Terminal strip

RS-422 control signal in

RS-422 control signal out

12 VDC wall

transformer

KTD-300R keypad

DTMF to KTS-41A

KTD-400 Controller Keypad

User Manual

KTD-400 configuration

After you install and power up your KTD-400 keypad, you will need to configure it to operate within your

systems. You can also use the KTD-400 to configure other components in the Digiplex system. (See System

component configuration on page 10.)

The KTD-400 offers many programming choices that identify how it will function in the system. A separate

code is used to access the menus. For new installations, follow the programming steps in the order they are

presented. If you need to change any programmed data at a later date, enter the appropriate programming

mode and use the designated keys to advance the menu associated with that data.

• System size (see Figure 11 on page 7)

• Camera site access (see Figure 12 on page 7)

• Monitor access (see Figure 13 on page 8)

• Multiplexer enable and select (see Figure 14 on page 8)

• Multiplexer view display (see Figure 15 on page 8)

• VCR enabled (see Figure 16 on page 9)

• Maximum presets (see Figure 17 on page 9)

• Monitor offset (see Figure 18 on page 9)

When you supply power to the unit, the LCD will momentarily display a limited amount of configuration

information on the unit (Figure 7).

Figure 7. Programming display

After a few seconds, the normal operating display menu (Figure 8 on page 6) will appear.

To configure the KTD-400, do the following:.

1. In the normal operating display (Figure 8),

enter programming mode by pressing and

holding the Set key until you see the display

in Figure 9.

Figure 8. Normal operating display

2. At the code entry display (Figure 9), enter

the access code 5, 7, 9, Seq. Figure 9. Code entry display

Largest Largest Largest Largest Monitor Key

camera monitor multiplexer VCR offset layout

Revision number

KTD-400 DDMMYY

255 64 64 64 00 0

CAMERA 000

MONITOR 01

CAMERA 000 (CODE)

MONITOR 01 (----)

Inhaltsverzeichnis

Andere GE Controller Handbücher

GE AF-600 Anleitungen und Rezepte

GE IC3645SR4R333AS2 Bedienungsanleitung

GE IC3645SR4R333AS1 Bedienungsanleitung

GE Multilin GEK-113000T Bedienungsanleitung

GE IC3645SH7R353E2 Betriebsanleitung

GE PACSystems IC695CPU3104 Bedienungsanleitung

GE RSTi-EP Bedienungsanleitung

GE DPI 610 IS Bedienungsanleitung

GE SX Series Bedienungsanleitung

GE Multilin F650 Bedienungsanleitung

GE EV100 LX Bedienungsanleitung

GE RX3i PROFINET Bedienungsanleitung

GE VersaMax PLC Bedienungsanleitung

GE IC3645SR4W606MC2 Bedienungsanleitung

GE SVI II AP Bedienungsanleitung

GE Masoneilan 37 Bedienungsanleitung

GE ACUXL16 Bedienungsanleitung

GE ZW4002 Bedienungsanleitung

GE 400 Series Bedienungsanleitung

GE PACSystems* RX3i Bedienungsanleitung

GE MOTOR MANAGER 2 Bedienungsanleitung

GE PACSystems* RX3i Bedienungsanleitung

GE b30 Bedienungsanleitung

GE PACSystems* RX3i Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch