GE 28512 1-A Series Bedienungsanleitung

DECT 6.0 Cordless Phone

User¡s Guide

Models:

28512xx1-A/28512xx2-A/28512xx3-A/28512xx4-A

28522xx1-A/28522xx2-A/28522xx3-A/28522xx4-A

Getting started

Parts Checklist

Your telephone contains the following items. Save your sales receipt and original packaging in the event warranty service

is necessary.

Getting started

Telephone base and charging cradle installation

Install the telephone base and charging cradle(s) as shown below. Make sure that the electrical outlet is not controlled by

a wall switch.

If you have DSL high speed internet service, a DSL filter is required (not included). Contact your DSL service provider for

more information about DSL filter.

Telephone Jack Requirements

To use this phone, you need an RJ11C type modular telephone jack, which might look

like the one pictured here, installed in your home. If you don¡t have a modular jack, call

your local phone company to find out how to get one installed.

CAUTION: Use only the power adaptor that came with this unit. Using other power adaptors may

damage the unit.

Getting started

Installing the Handset Battery

CAUTION: To reduce the risk of fire or personal injury, use only the CCT Tech USA Inc. approved model

H-AAA550BX2 Nickel-metal Hydride battery (Ni-MH), which is compatible with this unit.

1. If the battery compartment cover is on the handset, slide the cover to remove.

2. Plug the battery connector securely into the socket inside the handset battery compartment

3. Place the battery and the wire inside the battery compartment

4. Align the cover flat against the battery compartment, then slide it towards the center of the handset until it clicks

into place

5. Charge the handset by placing it in the telephone base or charging cradle. The battery icon on LCD is scrolling

when the handset charges.Please Fully Charge Before Using!

For optimum battery performance, charge the battery for 16 hours before use.

Note: If the handset will net be used for a long time, disconnect and remove the battery to prevent possible leakage.

Getting started

Battery charging

Once you have installed the battery, the screen indicates the battery status (see the table below). If necessary, place the

handset in the telephone base or charging cradle to charge the battery. For best performance, keep the handset in the

telephone base or charger when not in use. The battery is fully charged after 16 hours of continuous charging.

The following table summarizes the battery charge indicators and actions to take.

Battery indicators Battery status Action

Battery icon is scrolling Battery is charging

The battery is not full. Please keep the handset on base

cradle or charging cradle until handset fully charged

Battery icon is steady on Battery is charged

To Keep battery charged, place it in the telephone base

or charging cradle when not in use

Battery icon is empty Battery has enough charge to

be use for a short time Charge without interruption (at least 30 minutes)

LCD shows "INITIAL" Battery has very little or no

charge. The handset cannot

be used. Charge without interruption (at least 30 minutes)

Getting started

Base layout Find: Press to page all system handsets

Find: Press to page all system handsets.

Volume up/down: Press to adjust the

volume during playback and call screening.

Play/Stop: Press to play message or press to

stop message playback.

Repeat: Press to repeat a message or press

twice to play previous message.

Forward: Press to skip to the next message.

Delete: Press to delete the message during

playback or press and hold to delete all old message.

Memo rec.: Press and hold to record memo.

Annc. Rec.: Press and hold to record the outgoing message.

Answer on/off: Press to turn the answering system on and off.

Getting started

Handset layout OK: Press to select an item, or save an

entry or settings.

Delete: Press to delete the last input

number or letter.

While in a menu, press to return the

upper level without making changes.

Up/CID: Press to review the call log

when the telephone is not in use.

While in a menu, press to scroll up.

During a call, press to increase the

listening volume.

Down/Phonebook: Press to review the

phonebook when the telephone is not in

use.

While in a menu, press to scroll down.

During a call, press to increase the

listening down.

Talk/Flash: Press to make or answer a

call.

During a call, press to answer an

incoming call when you receive a call

waiting alert.

End: During a call, press to hang up.

During a programming, press to exit without making changes.

Menu: Press to show menu.

Speaker: Press to make or answer a call though speakerphone.

During a call, press to switch between speakerphone and handset.

Redial: Press to review redial list.

*/Format: Press to hidden or display the international code or area code in call log.

#/Ringer off: Press and hold to set the Ringer off when the telephone is not in use.

Mute: While on a call, press to mute the microphone.

Intercom: Set up the intercom between handset to handset.

Getting started

LCD display items

Item Meaning

Turn on when base unit range

Blinking when base out of range

Turn on during review the phone book

Animated while charging to indicate Battery level

On when handset is out of charging cradle

Flashes and empty when battery level is low

Blinking when there is incoming call

Steady on during a call

Flashes when there is a new voice mail message ( see note page x)

Turn on when Alarm set

Turn on when ringer off set

Blinking when there is a missing call

Turn on during review the call log and when is new record in call log

Only available on answering system model (28522)

Answering system is ON

Flashes when there is new message

Telephone settings

Display language

You can select either ¡ENGLISH¡ or ¡ESPA?OL¡ or ¡FRANCIS¡ as the display language. The default setti ng is ¡ENGLISH¡

1. Press [ ], then

2. Press [ ]/[ ] to select ¡SETTINGS¡ and press [OK], then

3. Press [ ]/[ ] to select ¡LANGUAGE¡ and press [OK], then

4. Press [ ]/[ ] to select the desired setting, then

5. Press [ ] and [ ] return to idle

Dialing mode

The default dialing mode is ¡Tone¡ for touch tone dialin g. If you have ¡pulse¡ or ¡rotary¡ service, change this setting to

accommodate your telephone line service.

1. Press [ ], then

2. Press [ ]/[ ] to select ¡ADVANCED SET¡ and press [OK], then

3. Press [ ]/[ ] to select ¡DIAL MODE¡ and press [OK], then

4. Press [ ]/[ ] to select the desired setting, then

5. Press [ ] and [ ] return to idle

Date and time

1. Press [ ], then

2. Press [ ]/[ ] to select ¡CLOCK&ALARM¡ and press [OK], then

3. Press [ ]/[ ] to select ¡DATE & TIME¡ and press [OK], then

4. Enter the current year, month and date by selecting 2 digits.

Example: May 16, 2010

Press [1], [0], [0], [5], [1], [6]

5. Enter the current hour and minutes by selecting 2 digits.

Example: 9:30 am

Press [0], [9], [3], [0]

Press [ ]/[ ] to select am or pm, then

6. Press [ ] and [ ] return to idle

Telephone settings

Date format

You can change the date display format. The default is Month/Day. The alternate format is Day/Month

1. Press [ ], then

2. Press [ ]/[ ] to select ¡CLOCK&ALARM¡ and press [OK], then

3. Press [ ]/[ ] to select ¡SET FORMAT¡ and press [OK], then

4. Press [ ]/[ ] to select ¡DATE FORMAT¡ and press [OK], then

5. Press [ ]/[ ] to select the desired setting (MM/DD OR DD/MM), then

6. Press [ ] and [ ] return to idle

Time format

You can change the time format, the default is 12 hour. The alternate is 24 hour

1. Press [ ], then

2. Press [ ]/[ ] to select ¡CLOCK&ALARM¡ and press [OK], then

3. Press [ ]/[ ] to select ¡SET FORMAT¡ and press [OK], then

4. Press [ ]/[ ] to select ¡TIME FORMAT¡ and press [OK], then

5. Press [ ]/[ ] to select the desired setting (12 HOURS OR 24 HOURS), then

6. Press [ ] and [ ] return to idle

Ringer Volume

1. Press [ ], then

2. Press [ ]/[ ] to select ¡SETTTINGS¡ and press [OK], then

3. Press [ ]/[ ] to select ¡HANDSET TONE¡ and press [OK], then

4. Press [ ]/[ ] to select ¡RINGER VOLUME¡ and press [OK], then

5. Press [ ]/[ ] to select the desired setting (VOLUME 1 to 4 and OFF), then

6. Press [ ] and [ ] return to idle

Note: You can also switch the ringer between off and on when handset is in standby

1. Press and hold the [#] key to switch the ringer from on to off

2. To switch back, press and hold the [#] key again

LCD will show ¡RINGER OFF¡ and a [ ] when ringer off feature is activated

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Beliebte Schnurloses Telefon Handbücher anderer Marken

3Com

3Com NBX Bedienungsanleitung

Panasonic

Panasonic KX-TGK210HK Bedienungsanleitung

Panasonic

Panasonic KX-TCA181EX Bedienungsanleitung

BT FREESTYLE 3200 Bedienungsanleitung

AT&T

AT&T CL84102 Bedienungsanleitung

BREZZICNI

BREZZICNI CL-3622 Bedienungsanleitung

Panasonic

Panasonic KX-TG1831NZ Bedienungsanleitung

Panasonic

Panasonic KX-TG7301E Bedienungsanleitung

Sanyo

Sanyo CLT-J70 Bedienungsanleitung

Amplicomms

Amplicomms BigTel 201 Bedienungsanleitung

AT&T

AT&T E1812B Bedienungsanleitung

Sanyo

Sanyo CLT-670 Bedienungsanleitung

Curtis

Curtis TC595 Bedienungsanleitung

Gigaset

Gigaset Gigaset 3000 Micro Bedienungsanleitung

Poly

Poly VVX D230 Einrichtungshandbuch

AT&T

AT&T 7625 Bedienungsanleitung

Panasonic

Panasonic KX-TGP700 Bedienungsanleitung

Radio Shack

Radio Shack 43-3557 Bedienungsanleitung