GE KTC-XP1 Bedienungsanleitung
KTC
-
XP1
UltraView Camera
With Xposure Technology
© 2004 GE Security
All Rights Reserved.
Any GE Security software supplied with
GE Security products is proprietary and
furnished under license and can be used or
copied only in accordance with the terms of
such license.
This document contains proprietary
information that is protected by copyright.
No part of this document may be
reproduced or transmitted in any form or by
any means without the prior written
permission of GE Security.
The information contained in this document
is subject to change without notice.
GE Security, in keeping pace with
technological advances, is a company of
product innovation. Therefore, it is difficult
to ensure that all information provided is
entirely accurate and up-to-date.
GE Security accepts no responsibility for
inaccuracies or omissions and specifically
disclaims any liabilities, losses, or risks,
personal or otherwise, incurred as a
consequence, directly or indirectly, of the
use or application of any of the contents of
this document.
For the latest product specifications, visit
GE Security online at www.gesecurity.com
or contact your sales representative.
For technical support before and after installation, call 800-469-1676.
Technical support is available 24 hours a day, 7 days a week.
Call: Tech Support 800-469-1676 (6 A.M. – 5 P.M. PST Monday through Friday)
Tech Support 541-740-3589 (all other times)
Main 800-343-3358 or 541-754-9133
Fax: Tech Support 541-752-9096 (available 24 hours a day)
Main 541-754-7162
Web: www.gesecurity.com
1047441A / February 2004
This equipment has been tested and
found to comply with the limits for a
Class A digital device, pursuant to part
15 of the FCC Rules. These limits are
designed to provide reasonable
protection against harmful interference
when the equipment is operated in a
commercial environment. This
equipment generates, uses, and can
radiate radio frequency energy and, if
not installed and used in accordance
with the instruction manual, may cause
harmful interference to radio
communications.
You are cautioned that any changes or
modifications not expressly approved
by the party responsible for compliance
could void the user's authority to
operate the equipment.
KTC-XP1 UltraView Camera Table of Contents
1047441A / February 2004 3
TABLE OF CONTENTS
BEFORE YOU BEGIN................................................................4
1PACKAGE CONTENTS ........................................................5
2INSTALLATION ...................................................................6
2.1 MAKING VIDEO CONNECTIONS....................................6
2.2 SETTING THE LENS-MODE DIP SWITCH ......................7
2.3 ATTACHING THE CUSTOMER-SUPPLIED LENS ...............8
2.4 MAKING POWER CONNECTIONS ..................................9
3PROGRAMMING ...............................................................10
3.1 OSD CONTROL OF MENUS ......................................10
3.2 PROGRAMMING WITH THE MENUS .............................10
3.2.1 Main Menu..................................................................11
3.2.2 Camera Setup ............................................................11
3.2.2.1 CHANGING THE SIGNAL FORMAT ....................12
3.2.2.2 ADDING A CAMERA ID....................................12
3.2.2.3 SETTING THE LENS MODE AND ADJUSTING THE
DEFAULTS.....................................................13
3.2.2.4 ADJUSTING THE SYNC MODE .........................15
3.2.2.5 ADJUSTING THE AUTOMATIC GAIN CONTROL
(AGC) ..........................................................16
3.2.2.6 EXITING CAMERA SETUP................................17
3.2.3 White Balance (ATW, ATW-WIDE, HOLD) ................17
3.2.4 Locations (Lighting Environments) .............................18
3.2.5 PTZ.............................................................................20
3.2.6 Exiting with Saving or Canceling Changes.................21
TROUBLESHOOTING...............................................................22
Before You Begin KTC-XP1 UltraView Camera
4 1047441A / February 2004
BEFORE YOU BEGIN
Read these instructions before installing or operating this product.
Note: This installation should be made by a qualified service person and should conform to
local codes.
This manual provides installation and operation information. To use this
document, you must have the following minimum qualifications:
• A basic knowledge of CCTV systems and components
• A basic knowledge of electrical wiring and low-voltage electrical
hookups
Use this product only for the purpose for which it was designed.
Customer Support
For assistance in installing, operating, maintaining, and troubleshooting
this product, refer to this document and any other documentation
provided. If you still have questions, contact Technical Support:
GE Security
Call: 800-469-1676
Fax: 541-752-9096
Note: You should be at the equipment, ready with details before calling Technical Support.
Conventions Used in this Manual
Boldface or button icons highlight command entries. The following
WARNING, CAUTION, and Note statements identify potential hazards:
* WARNING:
Improper use of this equipment can cause severe bodily injury or
equipment damage.
** CAUTION:
Improper use of this equipment can cause equipment damage.
Note: Notes contain important information about a product or procedure.
* This symbol indicates electrical warnings and cautions.
** This symbol indicates general warnings and cautions.
KTC-XP1 UltraView Camera Package Contents
1047441A / February 2004 5
1 PACKAGE CONTENTS
CAUTION:
Use direct plug-in UL listed power supplies marked Class 2 or
LPS (limited power source) of the required output rating as listed
on the unit.
Manual Camera C-mount adapter
(for C-mount lenses only)
Figure 1. Package contents
Note: The manual includes a quick reference guide for installation and programming. It is
located in the fold of the manual.
Installation KTC-XP1 UltraView Camera
6 1047441A / February 2004
2 INSTALLATION
2.1 MAKING VIDEO CONNECTIONS
Note: With the Xposure technology, both the BNC (composite) and S-video (Y/C video)
connections provide sharper images of all scenes (especially high-contrast scenes). The
S-video connection, however, provides even greater clarity over the BNC connection.
See Figure 2 and perform the following:
Coaxial cable with BNCs
between MON.OUT and
test or local monitor
Coaxial cable with BNCs
between VIDEO OUT
and monitor, multiplexer,
or switcher
S-video cable between
S-VIDEO and monitor
Figure 2. Video connections
Note: You can connect up
to three monitors (or
devices) to each camera.
1) Connect a coaxial cable terminated with BNC connectors between
the MON.OUT connector of the camera and the video in connector
on a test or local monitor.
2) Connect a coaxial cable terminated with BNC connectors between
the VIDEO OUT connector of the camera and the video in
connector on a monitor, multiplexer, switcher, or other standard
video device.
3) Connect an S-video (Y/C video) cable between the S-VIDEO
connector of the camera and the video in connector on a high-
resolution surveillance monitor.
Note: If you’re not seeing the video quality that you expect with the S-video
connection, consult your company’s S-video technician.
KTC-XP1 UltraView Camera Installation
1047441A / February 2004 7
2.2 SETTING THE LENS-MODE DIP SWITCH
Note: If your lens has a manual iris, ignore this switch. It is for autoiris lenses only.
See Figure 3 and set switch as shown:
Set to VD
(video drive) for:
Autoiris lenses
with built-in amplifier
(i.e., video-type
lenses)
Set to DD
(direct drive) for:
Autoiris lenses
without amplifier
(i.e., DC-type
lenses)
DD adjustment
(see note)
Figure 3. Lens-mode DIP switch settings and iris level adjustment
Note: When the lens-mode DIP switch is set to DD, you can use the DD level screw (iris
level adjustment) to ensure the correct exposure of images for the camera’s position and
the lighting conditions. Use an insulated tool to rotate the screw. Observe the results on the
monitor screen for the best setting.
Note: The circuitry and programming must be set to the same setting for autoiris lenses.
Refer to section 3.2.2.3 Setting the Lens Mode and Adjusting the Defaults.
Installation continues on next page.
Installation KTC-XP1 UltraView Camera
8 1047441A / February 2004
2.3 ATTACHING THE CUSTOMER-SUPPLIED LENS
Note: For optimal performance, use an autoiris lens.
Refer to the instructions that came with the lens you purchased for
complete installation instructions of the lens.
In general, see Figure 4 and perform the following:
Video-type
autoiris
lens leads:
Pins for
solder side
of lens plug
C-mount adapter
(for C-mount lenses only)
Pins for
solder side
of lens plug
DC-type
autoiris
lens leads:
Red (9 VAC)
NC
(no connection)
Black (ground)
White (video)
Damping coil (+)
Damping coil (–)
Driving coil (+)
Driving coil (–)
Camera Autoiris lens
connector
Autoiris lens
plug
Lens
(autoiris lens shown;
a manual iris lens has no cable)
Figure 4. Attaching the customer-supplied lens
1) If you are using a C-mount lens, screw on the provided C-mount
adapter.
2) Screw the customer-supplied lens to the camera.
3) If you are using an autoiris lens, insert the autoiris lens plug into the
autoiris lens connector.
KTC-XP1 UltraView Camera Installation
1047441A / February 2004 9
2.4 MAKING POWER CONNECTIONS
CAUTION:
yUse direct plug-in UL listed power supplies marked Class 2 or
LPS (limited power source) of the required output rating as listed
on the unit.
yComplete all instruction steps before supplying power to the unit.
See Figure 5 and perform the following:
Connect a universal
12 VDC/24 VAC power
supply as shown
Note: The terminal block is not
polarity-sensitive.
Note: The power LED ( )
illuminates to show that the
camera is receiving power.
Figure 5. Power connections
1) With a screwdriver, loosen the ~AC24V/DC12V and GND terminal
screws on the terminal block.
2) Connect a universal 12 VDC/24 VAC power supply to the terminal block.
Note: The terminal block is not polarity-sensitive. Either power lead can be
connected to either terminal connector.
3) Retighten the terminal screws until snug, ensuring that the power
leads are secure.
4) Supply power to the unit by plugging the power supply into a proper
power source.
Note: The power LED ( ) illuminates to show that the camera is receiving power.
If it does not illuminate, check the terminal block connections and the power source.
Programming KTC-XP1 UltraView Camera
10 1047441A / February 2004
3 PROGRAMMING
Use the OSD (on-screen display) menus to program the camera.
3.1 OSD CONTROL OF MENUS
OSD menu controls:
Use the center selection
button to enter a menu or
to select a menu option.
Use the up and down
buttons to move vertically
between menus and
options.
Use the right and left
buttons to move
horizontally to and
between options.
Figure 6. OSD (on-screen display) menu controls
Note: Wherever the PREVIOUS PAGE option appears, use it to leave the current menu
and return to the previous menu. Move to the PREVIOUS PAGE option and press .
3.2 PROGRAMMING WITH THE MENUS
To access the main menu:
Press and hold the center selection
button ( in Figure 6) for a few
seconds.
Note: Factory defaults are shown.
MAIN MENU
CAMERA SETUP.
WHITE BALANCE ATW
LOCATIONS GENERAL
PTZ.
EXIT SAVECHANGES.
Inhaltsverzeichnis
Andere GE Digitalkamera Handbücher
GE
GE J1456W Bedienungsanleitung
GE
GE J1470S Bedienungsanleitung
GE
GE Power series E1410SW Bedienungsanleitung
GE
GE POWER series E1486TW Bedienungsanleitung
GE
GE SMART A1455 Bedienungsanleitung
GE
GE J1470S Bedienungsanleitung
GE
GE A1035 Bedienungsanleitung
GE
GE J1456W Bedienungsanleitung
GE
GE A1035 Konfigurationshandbuch
GE
GE C1440W Konfigurationshandbuch
GE
GE J1458W Bedienungsanleitung
GE
GE E1680W Bedienungsanleitung
GE
GE POWER Pro series X5 Bedienungsanleitung
GE
GE A950 Bedienungsanleitung
GE
GE J1456W Bedienungsanleitung
GE
GE J1470S Bedienungsanleitung
GE
GE J1456W Referenzhandbuch
GE
GE Power series E1410SW Einrichtungshandbuch
GE
GE POWER series E1486TW Einrichtungshandbuch
GE
GE J1470S Bedienungsanleitung
