GE GE 19209 Bedienungsanleitung

GE Model 19209

www.jascoproducts.com

Wireless Door Chime Kit

Installation Instructions for Battery Operated

Wireless Door Chime Kit

Required Tools: Small flat blade screwdriver, drill, drill bit, and phillips

screwdriver.

Included Hardware:

(2) Plastic screw anchors

(2) 4x20mm screws (for anchors)

(2) 3x20mm screws

(2) Double sided adhesive pads

The wireless door chime Kit has two components:

Chime (receiver) Push-Button (Transmitter).

Chime Tune Setting

All wireless chimes may have more than one push button. The chime tune for

each push button is set with jumpers 7-9.

Single Push Button Kit: If you purchased a kit with a single push button, the

chime tune will be set to Ding Dong from the factory.

Dual Push Button Kit: If you purchased a kit with two push buttons, one push

button will be set to Ding Dong and the other push button will be set to

Westminster from the factory.

The following instructions explain how to change the tune on any wireless push

button.

1. Remove the battery from the push button transmitter.

2. Locate the 9 position jumper shown below.

9 position jumper (This pushbutton is set for Ding Dong Chime since 7=off, 8=on,

and 9=off.)

3. Select the desired chime sound from the table below.

Chime Sound Table

Position 7 8 9

Westminster ON OFF OFF

Ding Dong OFF ON OFF

Knock OFF OFF ON

Bronze Chime ON ON OFF

Cuckoo Clock ON OFF ON

Foghorn OFF ON ON

Gong ON ON ON

ON: Add a jumper to a location

OFF: Remove jumper from a location.

4. Remove or add the jumpers to match the table.

5. Store unused jumpers as shown in the picture.

Parking the jumper on an open set of pins. The two jumpers on the left are in the

parked position.

Setting The House Security Code

Each chime component has jumpers for setting the house security code.

In most cases you will not need to change the factory settings for the

security code. If your chime activates intermittently or does not work at all,

you may be able to solve the problem by changing your security code.

The chime and pushbutton must be set to the same house security code for the

combination to operate together.

Note: The push button has 3 additional jumpers that are used to set the chime

tune that will play. The chime tune jumpers do not affect the house security code.

1. Remove power or batteries from the chime.

2. To remove the batteries from the pushbutton, open the pushbutton case

as shown below.

3. Locate the House Security Code door and screw located on the

back of the AC Chime. Remove the screw and take off the door.

4. Locate the chime and pushbutton jumpers shown below.

Push Button Jumpers Chime Jumpers

5. Jumpers 1-6 are used to select 1 of 64 possible home security codes.

6. To change the house code, add or remove jumpers as needed. It is

recommended to change only one jumper at a time and then test the

system for proper operation. Positions 1-6 on the chime and pushbutton

must match exactly.

Push Button Mounting Instructions

Note: Avoid mounting the push button on metal surfaces, as it may result

in a reduced range of transmission. Do not mount in an area of rain (direct

weather.)

a. Removing the back cover

b. Replacing the back cover

1. Push buttons are typically mounted at the same height as the door knob or

handle (between 36" and 44" above the floor).

2. Before mounting, choose a mounting location that is not farther than 150

feet from the chime unit location.

Not farther than 150 feet

Place push button where you would like to mount and test operation with

the chime as close to it’s final location as possible. If it works, mount

button here. Do not mount in an area of rain (direct weather.) If it does not

work, see TROUBLESHOOTING.

3. Use back cover of push button as a template to mark two screw holes.

4. Drill two holes with 3/32” drill in marked locations.

5. Secure back cover to the mounting surface with two supplied mounting

screws.

6. Press front housing onto back cover.

7. Test Operations, if chime does not work, see TROUBLESHOOTING.

Chime Unit Mounting Instructions

Note: Avoid mounting the push button on metal surfaces, as it may result

in a reduced range of transmission.

1. Select chime mounting location.

2. Use the supplied chime template to mark mounting holes.

3. Drill ¼” holes at marked locations.

4. Insert supplied wall anchors into the holes.

5. Insert two of the supplied screws into the anchors, setting the screw heads

extending about 1/4" from mounting surface.

6. Place the chime unit’s keyhole slots over the screws and press down on

the chime unit to secure it.

Operation

1. Slide power switch to “On” to turn on the chime.

2. Gently press transmitter button to sound chime.

Troubleshooting

Chime doesn't work:

1. Make sure push button switch is depressed and held for at least 1 second.

2. Make sure plastic tag is removed from battery.

3. Make sure house code switches 1-6 on chime and push button match

exactly.

4. Verify battery orientation in push button.

5. Try fresh batteries.

6. Make sure chime is not farther than 150 feet away from push button.

7. Ensure push button is not mounted on metal, near metal studs, or near the

floor.

8. Try a new location for the chime.

Functional range may be adversely affected by one or more of the following

factors: weather, radio frequency interference, low transmitter battery and

obstructions between the transmitter and receiver.

This device complies with Part 15 of the FCC rules. Operation is subject to the

following conditions:

1. This device may not cause harmful interference, and

2. This device must accept interference received, including any interference that

may cause undesired operation.

For technical support contact Jasco Products Company at 1-800-654-8483

or www.jascoproducts.com

Made in China

is a trademark of

General Electric Company

and is used under license to

Jasco Products Company LLC,

311 N.W. 122nd Street,

Oklahoma City, OK 73114.

www.jascoproducts.com

Rev. 1-07 19209

Andere Handbücher für GE 19209

Inhaltsverzeichnis

Andere GE Tür Handbücher

GE 19298 Bedienungsanleitung

GE 19214 Bedienungsanleitung

GE 19204 Bedienungsanleitung

GE 19210 Bedienungsanleitung

GE 19217 Bedienungsanleitung

GE 19216 Bedienungsanleitung

Beliebte Tür Handbücher anderer Marken

ENFORCER

ENFORCER Enforcer SK-990A Bedienungsanleitung

Electri-Chef

Electri-Chef TR18 Betriebsanleitung

BEA

BEA PBR45x Bedienungsanleitung

Sterling Plumbing

Sterling Plumbing Frameless Bypass Shower Door SP5465-45 Bedienungsanleitung

Ives

Ives 55 Bedienungsanleitung

Algoma Hardwoods

Algoma Hardwoods STC 39 Bedienungsanleitung

Ives

Ives Surface Bolt 43 Bedienungsanleitung

Therma-Tru

Therma-Tru Double-door Bedienungsanleitung

Erreka

Erreka PREMIS 200 Bedienungsanleitung

Ives

Ives Surface Bolt 144 Bedienungsanleitung

Lennox Hearth Products

Lennox Hearth Products MPB-35 Bedienungsanleitung

Ives

Ives Offset Top Pivot 7245F Bedienungsanleitung

KitchenAid

KitchenAid KBAU181V Handbuch

Ives

Ives 670 Bedienungsanleitung

Ives

Ives Mortise Bolt S48 Bedienungsanleitung

American Standard

American Standard Acrylux 6000Y1.BE5 Bedienungsanleitung

Ives

Ives 671 Bedienungsanleitung

Albany

Albany RCA L Bedienungsanleitung