GE GTX18ESSJ Handbuch

For answers to your Monogram,® GE Profile™or

GE®appliance questions, visit our website at

geappliances.com or call GE Answer Center®

service, 800.626.2000.

Listed by

Underwriters

Laboratories

Specification Created 8/14

GTX18ESSJ

GE®6.0 cu. ft. capacity Dura Drum electric dryer

Electric Dryer Rating:

240V 5600W 24A 60Hz

208V 4400W 22A 60Hz

Exhaust Option: 4-way rear, right, left

and bottom

Circuit Requirements: An individual,

properly-grounded branch circuit, protected

by a 30-amp circuit breaker or a time-delay

fuse, is required.

Note: Dryer wall outlet must be located within

36" of service cord entry and acessible when

dryer is mounted in position.

Installation Information: For complete

information, see installation instructions

packed with your dryer.

Dimensions and Installation Information (in inches)

Special Installation Requirements

Alcove or Closet Installation:

• If your dryer is approved for installation in an alcove or closet, it will be stated on a label

on the dryer back.

• The dryer MUST be exhausted to the outside.

• Minimum clearances between dryer cabinet and adjacent walls or other surfaces are:

0" either side; 3" front and rear

• Minimum vertical space from floor to overhead cabinets, ceilings, etc. is 52”.

• Closet doors must be louvered or otherwise ventilated and must contain a minimum

of 60 sq. in. of open area equally distributed. If this closet contains both a washer and

a dryer, doors must contain a minimum of 120 sq. in. of open area equally distributed.

• No other fuel-burning appliance shall be installed in the same closet with a gas dryer.

Bathroom or Bedroom Installation:

• The dryer MUST be exhausted to the outdoors.

• The installation must conform with the local codes, or in the absence of local codes,

with the National Electric Code and National Fuel Gas Code, ANSI Z223 for gas dryers.

Minimum Clearances other than Alcove or Closet Installation:

• Minimum clearances to combustible surfaces are: 0" both sides; 3" rear

Dryer Exhausting Information: Use metal duct only, vertical and horizontal ducting.

For complete information, see installation instructions packed with your dryer.

Ducting Materials:

For best performance, this dryer should be vented with 4" diameter all rigid metal

exhaust duct. If rigid metal duct cannot be used, then UL-listed flexible metal (semi-

rigid) ducting can be used (Kit WX08X10077). In special installations, it may be

necessary to connect the dryer to the house vent using a flexible metal (foil-type) duct.

A UL-listed flexible metal (foil-type) duct may be used ONLY in installations where rigid

metal or flexible metal (semi-rigid) ducting cannot be used AND where a 4” diameter

can be maintained throughout the entire length of the transition duct. Please see

installation instruction packed with your dryer for complete instructions when using

flexible metal (foil type) ducting.

Exhaust Length Calculation:

1. Determine the number of 90° turns needed for your installation. If you exhaust to the

side or bottom of dryer, add one turn.

2.The maximum length of 4" rigid (aluminum or galvanized) duct which can be tolerated

is shown in the table. A turn of 45° or less may be ignored. Two 45° turns within the

duct length should be treated as a 90° elbow. A turn over 45° should be treated as a

90° elbow.

Dryers must be exhausted to the outside.

Caution: For personal safety do not terminate exhaust into a chimney, under any

enclosed house floor (crawl space), or into an attic, since the accumulated lint could

create a fire hazard or moisture could cause damage. Never terminate the exhaust

into a common duct or plenum with a kitchen exhaust, since the combination of lint

and grease could create a fire hazard.

Exhaust ducts should be terminated in a dampered wall cap to prevent back drafts,

bird nesting, etc. The wall cap must also be located at least 12" above the ground or

any other obstruction with the opening pointed down.

For more information on venting kits and accessories, please call 1-800-GE-CARES.

Dryer exhausting information—use metal

duct only vertical and horizontal ducting

2-1/2

GE Dryer Vent

2-1/2

GE Dryer Vent

Best performance

Maximum length

of 4" dia rigid

metal duct

Exhaust hood type

Domestic dryer models

Number

of 90°

turns

opening

2-1 /2"

opening

GE Frontload Long Vent 7.0

cu. ft. capacity electric dryer

(GFDL)

0200 ft. 175 ft.

1185 ft. 165 ft.

2175 ft. 155 ft.

3165 ft. 145 ft.

4155 ft. 135 ft.

5145 ft. 125 ft.

All Long Vent 6.0 - 8.0 cu. ft.

capacity electric & gas dryers

(GTDL)

0150 ft. 125 ft.

1135 ft. 115 ft.

2125 ft. 105 ft.

3115 ft. 95 ft.

4105 ft. 85 ft.

595 ft. 75 ft.

All 6.0 - 8.3 cu. ft. capacity

models electric and gas dryers

(GFDS, GFDR, GFDN, GTDS,

GTDN, GHDN, GHDS, GTDP,

GLDP, GTDX, HTDP, HTDX)

090 ft. 60 ft.

160 ft. 45 ft.

245 ft. 35 ft.

335 ft. 25 ft.

425 ft. 15 ft.

DCVH480

090 ft. 60 ft.

160 ft. 45 ft.

245 ft. 35 ft.

335 ft. 25 ft.

All 3.6 cu. ft. (DSKS, DSKP)

electric dryers

046 ft. 37 ft.

137 ft. 30 ft.

230 ft. 22 ft.

323 ft. 15 ft.

Laundry Center GTUP270,

GTUN275

056 ft. 42 ft.

148 ft. 34 ft.

240 ft. 26 ft.

332 ft. 18 ft.

Laundry Center GTUP240

043 ft. 36 ft.

133 ft. 26 ft.

224 ft. 16 ft.

For every extra 90° elbow, reduce the allowable vent system length by 10 ft.

Two 45° elbows will be treated like one 90° elbow.

For the side exhaust installations, add one 90° elbow to the chart.

The total vent system length includes all the straight portions and elbows of the system (transition

duct included).

Laundry Center length includes factory-installed elbow that does not impact vent length.

Specification Created 8/14

GTX18ESSJ

GE®6.0 cu. ft. capacity Dura Drum electric dryer

GTX18ESSJWW

Features and Benefits

• Dura Drum interior provides long-lasting dependability

• 4 heat selections provide the right temperatures for your clothes-

drying needs

• Quick Fluff delivers ready-to-go results in minutes without heat

• End-of-cycle signal - Alerts you when the load is done, so clothes can

be removed before wrinkles set in

• Auto Dry monitors air temperature to set dry times

• Model GTX18ESSJWW – White

Specification Created 8/14

GTX18ESSJ

GE®6.0 cu. ft. capacity Dura Drum electric dryer

Andere GE Trockner Handbücher

Beliebte Trockner Handbücher anderer Marken

Bosch

Bosch WTA79200GB Bedienungsanleitung

Amana

Amana W10233410A Bedienungsanleitung

Asko

Asko T760 Bedienungsanleitung

Bosch

Bosch Logixx 10 WTB76556GB Technisches Datenblatt

Electrolux

Electrolux EW2H328R2 Bedienungsanleitung

Beko

Beko DS8433RX1M Bedienungsanleitung

Dawlance

Dawlance Spinner DS 6000 C Bedienungsanleitung

Electrolux

Electrolux TP5080TW Bedienungsanleitung

AEG

AEG TR838P4OB Bedienungsanleitung

Indesit

Indesit IDV 75 Bedienungsanleitung

Infiniton

Infiniton SD-DG85C Bedienungsanleitung

BOMANN

BOMANN WT 5019 Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems TMB795C Bedienungsanleitung

Asko

Asko T793C Bedienungsanleitung

Kenmore

Kenmore 8041 - 5.8 cu. Ft. Capacity Electric Dryer Bedienungsanleitung

Frigidaire

Frigidaire CAQE7077KW0 Betriebsanleitung

Bosch

Bosch WTX8HKM9SN Bedienungsanleitung

Sharp

Sharp KD-NHH9S7GW2-PL Bedienungsanleitung