GE BFLH70L Bedienungsanleitung

BFLH70L, BFLH85L

Heater/Exhaust Fan/Light User’s Guide

210572111 Rev. B 5-06

Item Stock Number(s): BFLH70L, BFLH85L

READ AND SAVE THESE INSTRUCTIONS

READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE OR MAINTAIN THE PRODUCT DESCRIBED.

PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY INFORMATION. FAILURE TO COMPLY WITH

INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE!

RETAIN INSTRUCTIONS FOR FUTURE REFERENCE.

GENERAL SAFETY INFORMATION

When using electrical appliances, basic precautions should always be followed to reduce

the risk of fire, electric shock and injury to person, including the following:

1. Read all instructions before installing or using

exhaust fan.

2. Use this unit only in the manner intended by the

manufacturer. If you have questions, contact the

manufacturer.

3. Before servicing or cleaning the unit, switch power

off at service panel and lock the service disconnecting

means to prevent power from being switched on

SAVE THESE INSTRUCTIONS

IMPORTANT INSTRUCTIONS -

OPERATING MANUAL

accidentally. When the service disconnecting means

cannot be locked, securely fasten a prominent warning

device, such as a tag, to the service panel.

4. Installation work and electrical wiring must be done

by qualified person(s) in accordance with all applicable

codes and standards, including fire-related construction.

5. Sufficient air is needed for proper combustion and

exhausting of gases through the flue (chimney) of

1 of 8

www.geelectrical.com

210572111 Rev. B 5-06

GENERAL SAFETY INFORMATION

(Continued)

fuel burning equipment to prevent back drafting. Follow

the heating equipment manufacturer’s guideline and

safety standards such as those published by the National

Fire Protection Association (NFPA) and the American

Society for Heating, Refrigeration, and Air Conditioning

Engineers (ASHRAE), and the local code authorities.

CAUTION: FOR GENERAL VENTILATING USE

ONLY. DO NOT USE TO EXHAUST HAZARDOUS OR

EXPLOSIVE MATERIALS AND VAPORS.

6. When cutting or drilling into wall or ceiling, do not

damage electrical wiring and other hidden utilities.

7. Ducted fans must always be vented to the outdoors.

8. This unit must be grounded.

9. To avoid motor bearing damage and noisy and/or

unbalanced impellers, keep drywall spray, construction

dust, etc. off power unit.

WARNING: TO REDUCE THE RISK OF FIRE,

ELECTRIC SHOCK, DO NOT USE THIS FAN WITH ANY

SOLID-STATE SPEED CONTROL DEVICE.

WARNING: DO NOT INSTALL OVER A TUB OR

MOUNT IN A SHOWER STALL ENCLOSURE.

10. Do not install into a ceiling thermally insulated to a

value greater than R-40.

11. NEVER place a switch where it can be reached from

a tub or shower.

WARNING: DO NOT USE IN KITCHENS

WARNING: THIS UNIT IS DESIGNED AND TESTED

TO BE A SUPPLEMENTAL HEATER FOR USE WITH A

TIMER OR A SWITCH. IT IS NOT INTENDED TO BE USED

AS THE PRIMARY SOURCE OF HEAT AND CONTROLLED

BY A THERMOSTAT.

INSTALLATION INSTRUCTIONS

CAUTION: MAKE SURE POWER IS SWITCHED OFF

AT SERVICE PANEL BEFORE STARTING INSTALLATION.

SECTION 1

Preparing the Unit

1. Unpack fan from the carton and confirm that all pieces

are present. In addition to the unit you should have:

1 - Grill with Light Lens

4 - Mounting Rails

1 - Instruction/Safety Sheet

2. Remove the two machine screws holding the light

reflector in place. Keep the reflector and screws in

the carton until needed so they do not get damaged

or lost. (Figure 1).

3. Remove the wire compartment cover by loosening

the two screws holding the cover in place (Figure 2)

WARNING: DO NOT INSTALL OVER A TUB OR

MOUNT IN A SHOWER STALL ENCLOSURE.

4. Choose the location for your unit. To ensure the best

air and sound performance, it is recommended that

the length of ducting and the number of elbows be

kept to a minimum, and that insulated hard ducting

be used. Larger duct sizes will reduce noise and

airflow restrictions. This fan will require at least 7"

of clearance in the ceiling, and will mount through

drywall up to 3/4" thick. The fan can be mounted

directly to the joist using the mounting tabs on the

side of the housing or between

16" on center joists using the

4 provided mounting rails.

5. Remove the electrical

knockouts using a straight-

blade screw driver (Figure 3).

SECTION 2

New Construction

1. Mounting Rail Installation: Install the rails on the

housing and position the housing next to the joist.

Line up housing so it will be flush with the finished

2 of 8

Figure 1

Screws

Figure 2

Screws Wire

Compartment

Cover

Figure 3

www.geelectrical.com

210572111 Rev. B 5-06

ceiling. Secure the ends of the rails with screws or

nails (not included) to the joists and slide housing

into final position (Figure 4).

1a. Mounting Tab Installation: Line up housing so that

it will be flush with the finished ceiling. Position the

fan so that the tabs rest flat against the joist and

secure with screws or nails (not provided) to ensure

proper installation (Figure 5).

SECTION 3

Existing Construction

1. Mounting Rail Installation: Set housing in position

between the joist and trace an outline onto the ceiling

material (Figure 6). Set housing aside and cut opening,

being careful not to cut or damage any electrical or

other hidden utilities. Install the rails on the housing

and position the housing in the previously cut hole so

that it is flush with the finished ceiling. Secure the

ends of the rails to the joists with screws or nails (not

provided) to ensure proper installation (Figure 4).

1a. Mounting Tab Installation: Position housing against

the joist and trace an outline of the housing onto the

ceiling material (Figure 7). Set housing aside and

cut opening, being careful not to cut or damage any

electrical or other hidden utilities. Place housing

next to the joist and insure that it is flush with the

finished ceiling. Secure with screws or nails (not

provided) to the joists (Figure 5).

SECTION 4

Ducting

CAUTION: ALL DUCTING MUST COMPLY WITH

LOCAL AND NATIONAL BUILDING CODES.

1. Remove any tape that might be holding the damper

in place during shipping and connect the ducting to

the fan’s duct collar (Figure 8). Secure in place using

tape or screw clamp. Always duct the fan to the

outside through a wall or roof cap.

SECTION 5

Wiring

CAUTION: MAKE SURE POWER IS SWITCHED OFF

AT SERVICE PANEL BEFORE STARTING INSTALLATION.

WARNING: THIS UNIT MUST BE WIRED ON A

SEPARATE 20 AMP CIRCUIT.

CAUTION: ALL ELECTRICAL CONNECTIONS MUST

BE MADE IN ACCORDANCE WITH LOCAL CODES,

ORDINANCES, OR NATIONAL ELECTRICAL CODE. IF YOU

ARE UNFAMILIAR WITH METHODS OF INSTALLING

ELECTRICAL WIRING, SECURE THE SERVICES OF A

QUALIFIED ELECTRICIAN.

3 of 8

Figure 4

Joist

Housing

Mounting Rails

Figure 5

Figure 6

Figure 7

Figure 8

www.geelectrical.com

210572111 Rev. B 5-06

1. Run wiring from approved wall switches carrying

the appropriate rating. One neutral (white), one

ground (green or bare copper), and three hot (black,

red, blue leads connected to the switch, one for

each function). Secure the electrical wires to the

housing with an approved electrical connector. Make

sure you leave enough wiring in the box to make the

connection to the fan’s receptacles.

2. Connect the white wire from the house to the three

white wires from the fan. Connect one hot (black)

wire from the wall switch to the black wire from the

fan (this is the fan control). Connect second hot (red)

wire from the wall switch to the red wire from the

fan (this is the heat control). Connect the third hot

(blue) wire from the wall switch to the blue wire from

the fan (this is the light control). Connect the ground

wire from the house to the green wire from the fan

(Figure 9). Use approved methods for all connections.

3. Reinstall the wire compartment cover by sliding the

tabs at the bottom of the cover into the slots in the

housing. Make sure all wires are tucked inside of the

compartment and are not being pinched or showing

through. Reinstall the two screws removed in Step 3

of SECTION 1

Preparing the Unit

(Figure 10).

SECTION 6

Completing the Installation

1. Insert the plug from the heating unit into the

receptacle marked “HEAT”, and the plug from the

fan into the receptacle marked “VENT”(Figure 11).

2. Remove grill from carton and open light lens area

by pushing in on the two tabs of the light lens and

pulling outward from lens. The lens will swing open

on the connector bars. DO NOT remove the lens

from the grill (Figure 12).

3. Install light reflector into grill by lining up the posts on

grill with the holes in light reflector (Figure 13). Raise

light reflector and grill up to housing and insert plug

from light into receptacle marked “LIGHT” (Figure 11).

4 of 8

Figure 9

Ground

Supply from house

White

Hot (Blue)

Hot (Black)

Hot (Red)

Figure 10

Tab

Slot

Light

Figure 12

Tabs

Connector Bar

Figure 13

Hole

Post

Figure 11

Heater

Vent

www.geelectrical.com

Troubleshooting Guide

Trouble Probable Cause Suggested Remedy

1. Fan does not operate when the switch is on. 1a. A fuse may be blown or a circuit tripped. 1a. Replace fuse or reset circuit breaker.

1b. Connector plug from motor is not plugged in. 1b. Turn off power to unit. Remove Grill and plug motor into

receptacle in housing. Restore power to unit.

1c. Wiring is not connected properly. 1c. Turn off power to unit. Check that all wires are connected.

2. Fan is operating, but air moves slower than normal. 2. Obstruction in the exhaust ducting. 2. Check for any obstructions in the ducting. The most common

are bird nests in the roof cap or wall cap where the fan

exhausts to the outside.

3. Fan is operating louder than normal. 3a. Motor is loose. 3a. Turn off power to unit. Remove grill and check that all screws

are fully tightened. Restore power to unit.

3b. Fan blade is hitting housing of unit. 3b. Call your dealer for service.

210572111 Rev. B 5-06

SECTION 7

Use and Care

CAUTION: MAKE SURE POWER IS SWITCHED

OFF AT SERVICE PANEL BEFORE SERVICING THE UNIT.

1. Cleaning the Grill: Reverse the instructions in Section

Completing the Installation

to remove grill. Use a

mild detergent, such as dishwashing liquid, and dry

with a soft cloth. NEVER USE ANY ABRASIVE PADS

OR SCOURING POWDERS. Completely dry grill before

reinstalling. Refer to instructions in Section 6

Completing the Installation

, to reinstall grill.

2. Cleaning the Fan Assembly: Wipe all parts with a

dry cloth or gently vacuum the fan. NEVER IMMERSE

ELECTRICAL PARTS IN WATER.

CAUTION: ALLOW BULBS TO COOL BEFORE

REPLACING.

3. Changing the Light Bulb: Disconnect power to the

unit. Open light lens by pushing in on the two tabs

of light lens and pulling outward from lens. The lens

will swing open on the connector bars. DO NOT

remove the lens from the grill (Figure 16).

4. Unscrew bulb from lamp holder and replace with a

100 watt maximum, type A19 medium base

incandescent bulb.

5 of 8

4. Attach light reflector in place with the two screws

removed during

Step 2

in SECTION 1

Preparing the

Unit

so grill fits snuggly against ceiling (Figure 14).

CAUTION: FAILURE TO SECURE THE REFLECTOR

SCREWS MAY RESULT IN A RATTLING OR HUMMING

NOISE.

5. Install a 100 watt maximum, type A19 medium base

incandescent bulb (not included).

6. Close the light lens and secure in place by swinging

back into position and snapping the tabs in place

(Figure 15).

7. Restore power and test your installation.

Figure 14

Screws

Figure 15

Tabs

Connector Bar

Figure 16

Tabs

Connector Bar

www.geelectrical.com

WARRANTY

WHAT IS COVERED?

Full Five Year Parts Warranty from date of original proof of

purchase. We will provide, free of charge, a replacement part

that fails due to manufacturing defect in material or workmanship,

when installed and used as directed in the User’s Guide.

This warranty is extended to the original purchaser for products

purchased for ordinary home use.

Read your User’s Guide. If you have any questions about operating the product, please contact your dealer.

Some states and provinces do not allow the exclusion or limitation of incidental or consequential damages and some states

do not allow limitations on how long an implied warranty lasts, so these exclusions or limitations may not apply to you. This

warranty gives you specific legal rights and you may have other rights which vary from state to state and province to province.

WHAT IS NOT COVERED?

• Installation services or service trips to your home to teach

you how to use the product.

• Labor costs or the cost of replacement components as part

of routine maintenance.

• Failure or defects in product arising from Improper installation

If you have an installation problem, contact your dealer or

installer. You are responsible for providing adequate

electrical, exhausting and other connecting facilities. See

the Installation Instructions provided with this product for

electrical, exhaust and connection details.

• Replacement of house fuses or resetting of circuit breakers.

• Failure of the product if it is used for something other than

the intended purpose of manufacturer or used commercially.

• Damage to the product caused by accident, fire, floods,

acts of customer, or acts of God.

This warranty contains the sole and exclusive warranty of GE for claims based on defects in these products. Upon the expiration

of the warranty period, all such liability shall terminate. There are no other warranties, whether written, oral, implied or

statutory. NO IMPLIED STATUTORY WARRANTY OF MERCHANTABILITY OR FITNESS FOR PARTICULAR PURPOSE SHALL APPLY.

IN NO EVENT SHALL GE BE LIABLE FOR ANY SPECIAL, CONSEQUENTIAL, INDIRECT, OR INCIDENTAL DAMAGES, SUCH AS, BUT

NOT LIMITED TO, LOSS OF PROFIT OR REVENUES, LOSS OF USE OF THE PRODUCTS OR ANY ASSOCIATED EQUIPMENT, DAMAGE

TO ASSOCIATED EQUIPMENT, OR COST OF SUBSTITUTE PRODUCTS.

IN NO EVENT, SHALL GE’S LIABILITY TO BUYER FROM THE SALE OF THESE PRODUCTS EXCEED THE PRICE OF THE DEFECTIVE

PRODUCT SOLD AND ANY SUCH LIABILITY SHALL TERMINATE UPON THE EXPIRATION OF THE WARRANTY PERIOD.

210572111 Rev. B 5-06 6 of 8

www.geelectrical.com

210572111 Rev. B 5-06 7 of 8

REPLACEMENT PARTS DIAGRAM

# Qty. Description Replacement Part #

1 1 Fan Housing 5S3402039

2 4 Mounting Rails 5S1299002

3 2 Collar Screw 5S3402040

4 1 Collar 5S3402041

5 1 Damper 5S3402042

6 1 Motor - Vent 5S3402043

7 2 Motor Spacer 5S3402044

8 2 Motor Bracket Nut 5S3402045

9 2 Lock Washer 5S3402046

10 1 Motor Bracket - Vent 5S3402047

11 2 Washer 5S3402048

12 4 Lock Washer 5S3402049

13 4 Hex Nut 5S3402050

14 1 Vent Blower Wheel 5S3402051

15 3 #8 Screw 5S1999004

# Qty. Description Replacement Part #

16 1 Wire Compartment 5S3402052

17 3 Receptacle 5S3402053

18 1 Lamp Holder 5S3402054

19 1 Reflector 5S3402055

20 1 Grill 5S3402056

21 1 Lens Frame 5S3402057

22 1 Glass Lens 5S3402058

23 2 Reflector Screws 5S3402059

24 1 Motor - Heater 5S3402060

25 1 Heater Blower Wheel 5S3402061

26 1 Blower - Heater 5S3402062

27 1 Heater Plug Assembly 5S3402063

28 2 Over Heat Protector Screw 5S3402064

29 1 #10 Ground Screw 5S1999002

30 1 14 ga Ground Wire 5S1999003

13 14

12 13

www.geelectrical.com

210572111 Rev. B 5-06 8 of 8

www.geelectrical.com

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere GE Heizung Handbücher

GE ADTK15 Bedienungsanleitung

Beliebte Heizung Handbücher anderer Marken

oventrop

oventrop Regucor Series Bedienungsanleitung

Blaze King

Blaze King CLARITY CL2118.IPI.1 Bedienungsanleitung

ELMEKO

ELMEKO ML 150 Bedienungsanleitung

BN Thermic

BN Thermic 830T Bedienungsanleitung

KING

KING K Series Leitfaden

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Kurzanleitung

Well Straler

Well Straler RC-16B Bedienungsanleitung

EUROM

EUROM 333299 Bedienungsanleitung

Heylo

Heylo K 170 Bedienungsanleitung

Eterna

Eterna TR70W Bedienungsanleitung

Clarke

Clarke GRH15 Bedienungsanleitung

Empire Heating Systems

Empire Heating Systems WCC65 Bedienungsanleitung

Wetekom

Wetekom 92 86 43 Bedienungsanleitung

Desa

Desa SPC170-F Bedienungsanleitung

Watlow

Watlow Watrod Electric Tubular Heaters Bedienungsanleitung

Haverland

Haverland ECO-DRY GPS Series Stücklistenhandbuch

Stelpro

Stelpro ASILVC2060 Series Bedienungsanleitung

iLO

iLO IHP2424 Betriebsanleitung