GE 2 Cubic Foot Series Originalbetriebsanleitung

350A4502P296

GEAppliances.ca

Write the model and serial numbers here:

Model # __________________________

Serial # __________________________

Find these numbers on a label inside

the refrigerator on the side wall.

Refrigerators

2 Cubic Foot Models

3 Cubic Foot Models

4 Cubic Foot Models

Owner’s Manual

& Installation

Instructions

Safety Information . . . . . . . .2–3

Operating Instructions

Care and Cleaning . . . . . . . .6, 7

Control Settings . . . . . . . . . . . .4

Refrigerator Features . . . . . . . .5

Installation Instructions . . .8-10

Troubleshooting Tips . . . .11, 12

Consumer Support

Consumer Support . . . . . . . . .14

Warranty . . . . . . . . . . . . . . . . .13

www.GEappliances.ca

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

Safety Instructions

Operating InstructionsTroubleshooting Tips

Consumer Support Installation Instructions

DANGER! RISK OF CHILD ENTRAPMENT

Use this appliance only for its intended purpose as described

in this Owner’s Manual.

WARNING!

■This refrigerator must be

properly installed and located

in accordance with the

Installation Instructions

before it is used.

■Do not allow children to

climb, stand or hang on the

shelves in the refrigerator.

They could damage the

refrigerator and seriously

injure themselves.

■Do not store or use gasoline

or other flammable vapors

and liquids in the vicinity of

this or any other appliance.

■Keep fingers out of the “pinch

point” areas; clearances

between the doors and

cabinet are necessarily small.

Be careful closing doors when

children are in the area.

■Unplug the refrigerator

before cleaning and making

repairs.

NOTE: We strongly recommend

that any servicing be performed by

a qualified individual.

■Turning the temperature

control dial to the OFF

position stops cooling but

does not shut off power to

the refrigerator.

When using electrical appliances, basic safety precautions

should be followed, including the following:

SAFETY PRECAUTIONS

Child entrapment and

suffocation are not problems of

the past. Junked or abandoned

refrigerators are still dangerous…

even if they will sit for “just a few

days.” If you are getting rid of

your old refrigerator, please

follow the instructions below

to help prevent accidents.

Before You Throw Away Your Old

Refrigerator or Freezer:

■Take off the doors.

■Leave the shelves in place so

that children may not easily

climb inside.

CFC Disposal

Your old refrigerator has a

cooling system that used CFCs

(chlorofluorocarbons). CFCs are

believed to harm stratospheric

ozone.

If you are throwing away your

old refrigerator, make sure the

CFC refrigerant is removed for

proper disposal by a qualified

servicer. If you intentionally

release this CFC refrigerant you

can be subject to fines and

imprisonment under provisions

of environmental legislation.

PROPER DISPOSAL OF THE REFRIGERATOR

www.GEappliances.ca

Safety Instructions Operating Instructions Troubleshooting Tips Consumer SupportInstallation Instructions

USE OF EXTENSION CORDS

Because of potential safety hazards under certain conditions,

we strongly recommend against the use of an extension cord.

However, if you must use an extension cord, it is absolutely necessary

that it be a CSA approved, 3-wire grounding type appliance extension

cord having a grounding type plug and outlet and that the electrical

rating of the cord be 15 amperes (minimum) and 120 volts.

HOW TO CONNECT ELECTRICITY

Do not, under any circumstances, cut or remove the third

(ground) prong from the power cord. For personal safety,

this appliance must be properly grounded.

The power cord of this

appliance is equipped with

a 3-prong (grounding) plug

which mates with a standard

3-prong (grounding) wall outlet

to minimize the possibility of

electric shock hazard from

this appliance.

Have the wall outlet and

circuit checked by a qualified

electrician to make sure the

outlet is properly grounded.

If you have only a standard

2-prong wall outlet, it is your

personal responsibility and

obligation to have it replaced

with a properly grounded

3-prong wall outlet.

The refrigerator should

always be plugged into its own

individual electrical outlet

which has a voltage rating that

matches the rating plate.

This provides the best

performance and also prevents

overloading house wiring circuits

which could cause a fire hazard

from overheated wires.

Never unplug your refrigerator

by pulling on the power cord.

Always grip plug firmly and pull

straight out from the outlet.

Repair or replace immediately

all power cords that have

become frayed or otherwise

damaged. Do not use a cord that

shows cracks or abrasion damage

along its length or at either end.

When moving the refrigerator

away from the wall, be careful

not to roll over or damage the

power cord.

About the control

on the refrigerator.

Safety Instructions

Operating InstructionsTroubleshooting Tips

Consumer Support Installation Instructions

Control Settings

The temperature control maintains the temperature in the

refrigerator. Setting the control at COOL is the warmest setting. Setting

the control at COLDEST is the coldest setting. Set the control at COLD.

Allow 24 hours for the refrigerator to reach the COLD temperature.

If you want a colder or warmer temperature, move the dial one

setting at a time. Moving the control to OFF stops cooling but does

not turn off the power to the refrigerator. Setting the control to one

of the snowflake positions may cause freezing in the refrigerator

depending on the room temperature.

How To Test Temperatures

Use the milk test. Place a container of milk on a shelf and check it

a day later. If the milk is too warm or too cold, adjust the temperature

control.

After changing the control, allow 24 hours for the refrigerator to reach the

temperature you have set.

The control will look like one of the above.

OFF

COOL

COLD

COLDEST OFF

COOL

COLD

COLDEST

OFF

COOL

COLD

COLDEST

Safety Instructions Operating Instructions Troubleshooting Tips Consumer SupportInstallation Instructions

Shelves

To remove a shelf, lift up the back slightly and pull forward.

Some models have multi-position shelves that can be moved

to different levels.

Ice Tray Compartment

This compartment is designed for production of ice cubes and

short-term storage (a few days at most) of some commercially-

frozen foods when in contact with the evaporator (cold surface

in compartment.)

Door Shelves

Shelves on the door provide convenient storage for frequently

used items. Some models have doors that are deep enough to

store large bottles.

About the refrigerator features. www.GEappliances.ca

Key-Ejecting Lock (on some models)

The key for the spring-loaded lock is automatically ejected–

key will not remain in lock in either the open or closed position.

Keep the key out of reach of children and away from the refrigerator.

If a replacement key is needed, it can be ordered by visiting

our Website, GEappliances.ca, or calling GE Parts and Accessories,

1.888.261.3055 Order part WR05X10006.

Safety Instructions

Operating InstructionsTroubleshooting Tips

Consumer Support Installation Instructions

Cleaning the Outside

Keep the outside clean. Wipe with a clean cloth lightly dampened

with kitchen appliance wax or mild liquid dish detergent. Dry and

polish with a clean, soft cloth.

Do not wipe the refrigerator with a soiled dish cloth or wet towel. These may

leave a residue that can erode the paint. Do not use scouring pads, powdered

cleaners, bleach or cleaners containing bleach because these products can

scratch and weaken the paint finish.

Protect the paint finish. The finish on the outside of the refrigerator

is a high quality, baked-on paint finish. With proper care, it will

stay new-looking and rust-free for years. Apply a coat of kitchen/

appliance wax when the refrigerator is new, and then at least

twice a year.

Cleaning the Inside

To help prevent odors, leave an open box of baking soda in the

refrigerator.

Unplug the refrigerator before cleaning. If this is not practical,

wring excess moisture out of sponge or cloth when cleaning

around the control.

Use warm water and baking soda solution–about a tablespoon

(15 ml) of baking soda to a quart (1 liter) of water. This both

cleans and neutralizes odors. Rinse and wipe dry.

Other parts of the refrigerator–including door gaskets, fruit

and vegetable drawers, and all plastic parts–can be cleaned

the same way.

Do not wash any plastic refrigerator parts in the dishwasher.

Care and cleaning

of the refrigerator.

Safety Instructions Operating Instructions Troubleshooting Tips Consumer SupportInstallation Instructions

Preparing for Vacation

For long vacations or absences, remove food and unplug the

refrigerator. Move the control to the OFF position, and clean the

interior with a baking soda solution of one tablespoon (15 ml) of

baking soda to one quart (1 liter) of water. Leave the door open.

Preparing to Move

Secure all loose items such as shelves and ice trays by taping them

securely in place to prevent damage.

Be sure the refrigerator stays in an upright position during moving.

Defrosting

Defrost whenever frost on the wall of the ice tray compartment becomes

1/4″thick. Never use a sharp or metallic instrument to remove frost as

it may damage the cooling coils. (A punctured cooling coil will cause

serious problems and void the warranty.) We recommend using a plastic scraper.

Do not use any electrical device in defrosting your refrigerator.

To defrost, remove foods and ice trays from the ice tray compartment.

Set the temperature control dial at OFF position. Defrosting usually

takes a few hours. To defrost faster, keep the door open. Also,

pouring warm (not hot) water on the frosted part may speed

defrosting. Do not use boiling water—it may damage plastic parts.

After defrosting, empty water from the drip tray. Wash the drip tray

in warm water. Wipe the ice tray compartment with a damp cloth.

Then turn the temperature control to the desired setting and

return food and ice trays to the refrigerator.

NOTE: If ice build up is very thick, it may keep the ice tray compartment door

from opening or closing completely. Don’t try to force it open; after defrosting,

the door will open and close easily.

Care and cleaning

of the refrigerator. www.GEappliances.ca

Safety Instructions

Operating InstructionsTroubleshooting Tips

Consumer Support Installation Instructions

Preparing to install the refrigerator.

Read these instructions completely and carefully.

Turn counterclockwise to raise,

clockwise to lower.

Refrigerator Location

■Do not install the refrigerator where the temperature will go below

50°F (10°C) because it will not run often enough to maintain

proper temperatures.

■Install it on a floor strong enough to support it fully loaded.

■If the 2 cubic foot model is placed on a countertop or stand, the

front surface of the door should be 3″ or more back from the edge

of the countertop or stand to avoid accidental tipping of the

appliance during normal use.

■Do not install it closer than 5″(13 cm) next to a range.

■Do not install it in a recessed area.

■Do not build in the refrigerator.

Clearances

Allow the following clearances for ease of installation and proper

air circulation.

Sides 1/2″ (13 mm)

Top 2″(51 mm)

Back 2″(51 mm) from the rear cabinet surface to the wall

Leveling Legs (on some models)

Adjustable legs at the front corners of the refrigerator

should be set so the refrigerator is firmly positioned on

the floor and the front is raised just enough that the

door closes easily when opened about halfway.

To adjust the leveling legs, turn the legs counterclockwise

to raise the refrigerator, clockwise to lower it.

Safety Instructions Operating Instructions Troubleshooting Tips Consumer SupportInstallation Instructions

Leveling legs

Bottom

hinge

Plug button

Spacer

Hinge cover

Plug buttons

or screws Hinge

Preparing to install

the refrigerator. www.GEappliances.ca

Door Reversal

3 Cubic Foot Models

1. Remove the small plug button on the

left side of the door top cap.

2. Remove the three plug buttons or

screws on the left side on top of the

cabinet.

3. Remove the plastic hinge cover by

lifting it up by the front edge.

4. Remove the three screws from the

top hinge.

5. Lift the door up and off the bottom

hinge (right side).

6. Tilt the refrigerator cabinet back to

remove the right leveling leg.

7. Remove the screws on the bottom

hinge (right side) and the left leveling

leg. Move the bottom hinge to the left

side and secure it with the screws and

leveling leg.

IMPORTANT: The left leg has a spacer that

must be moved to the right side leveling leg

when the door swing is reversed.

8. Screw the right leveling leg, with the

spacer in place, back in place on the

right side.

9. Position the door on the left bottom

hinge. With the magnetic gasket

holding the door in place, secure the

top hinge with screws.

10. Make sure the door is aligned with the

refrigerator cabinet before continuing.

11. Replace the hinge cover on top of

the hinge.

12. Put the plug button in the hole on the

right side of the door cap.

13. Put the three plug buttons or screws on

the right side on top of the cabinet.

Safety InstructionsOperating InstructionsTroubleshooting TipsConsumer Support Installation Instructions

Preparing to install the refrigerator.

Door Reversal

(on some models)

4 Cubic Foot Models

1. Remove the two screws at the back of

the top cover.

2. Remove the top cover by lifting the back

up about 2″and then sliding it forward.

3. Remove the small plug button on the

left side of the door top cap.

4. Remove the three screws on the upper

hinge (right side). Remove the hinge.

5. Remove the three screws at the left

hinge location on the top plate.

6. Remove the screw in the middle of the

top plate and remove the top plate.

7. Lift the door up and off the bottom

hinge (right side).

8. Tilt the refrigerator cabinet back to

remove the right leveling leg.

9. Remove the screws on the bottom

hinge (right side) and the left leveling

leg. Move the bottom hinge to the left

side and secure it with the screws and

leveling leg.

IMPORTANT: The left leg has a spacer that

must be moved to the right side leveling leg

when the door swing is reversed.

10. Screw the right leveling leg, with the

spacer in place, back in place on the

right side.

11. Position the door on the left bottom

hinge. With the magnetic gasket

holding the door in place, secure the

top hinge with screws.

12. Make sure the door is aligned with the

refrigerator cabinet before continuing.

13. Replace the top plate and screws.

14. Slide the top cover back in place and

replace the two screws.

15. Put the plug button in the hole on the

right side of the door top cap.

Leveling legs

Bottom

hinge

Plug button

Spacer

Left hinge location

Upper

hinge

Top cover

Top

plate

Door

top cap

Andere Handbücher für 2 Cubic Foot Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Beliebte Kühlschrank Handbücher anderer Marken

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Bedienungsanleitung

Sharp

Sharp SJ-BA31IEXW2-EU Bedienungsanleitung

CORBERO

CORBERO CC2300MCW Bedienungsanleitung

KitchenAid

KitchenAid 2205264 Bedienungsanleitung

Stengel

Stengel KU 1101 A++ Bedienungsanleitung

NEFF

NEFF KI181 Series Bedienungsanleitung

Hoshizaki

Hoshizaki Reach-In Bedienungsanleitung

Amana

Amana ASD2524VES00 Bedienungsanleitung

BOMANN

BOMANN KGC 213 Bedienungsanleitung

Danby

Danby DAR044A1SLDD Montageanleitung

Samsung

Samsung RF323TE Bedienungsanleitung

Beko

Beko CSA31022 Bedienungsanleitung

IKEA

IKEA FROSTIG C 185 E Bedienungsanleitung

Electrolux

Electrolux ER 6821 D Bedienungsanleitung

True

True TS-28 Bedienungsanleitung

Frigidaire

Frigidaire FSC23R5DW9 Bedienungsanleitung

Beko

Beko LSP4579W Bedienungsanleitung