GE ETS19 P Series Anleitung zur Verwendung

PUB # 31-9108 11/03

"P" MODEL SERIES:

TECHNICAL SERVICE GUIDE

2003 Upgrade

Louisville Built

No Frost Top Freezer

18-19 Cu. Ft. Refrigerator

ETS19_ _P

GTH18_ _P

GTL18_ _P

GTS18_ _P

GTS19_ _P

HTS18_ _P

STS18_ _P

GE Consumer Products

https://appliancetechmanuals.com

– 2 –

GE Consumer Products

Technical Service Guide

in any form without written permission from the General Electric Company.

IMPORTANT SAFETY NOTICE

The information in this service guide is intended for use by

individuals possessing adequate backgrounds of electrical,

electronic, and mechanical experience. Any attempt to repair a

major appliance may result in personal injury and property

damage. The manufacturer or seller cannot be responsible for the

interpretation of this information, nor can it assume any liability in

connection with its use.

WARNING

To avoid personal injury, disconnect power before servicing this

product. If electrical power is required for diagnosis or test

purposes, disconnect the power immediately after performing the

necessary checks.

RECONNECT ALL GROUNDING DEVICES

If grounding wires, screws, straps, clips, nuts, or washers used to

complete a path to ground are removed for service, they must be

returned to their original position and properly fastened.

https://appliancetechmanuals.com

– 3 –

‘lk;lkm;lkm;/

General

The GE Louisville Built, No Frost Top Freezer, 18-19

Cu. Ft. Refrigerator models are being introduced with

a new Clean Steel™ door.

Other features include:

• A redesigned fresh food control panel.

• A redesigned fan motor mounting.

• A replaceable kick plate on non-freezer light

equipped models.

Introduction

Components.................................................................................................................................. 7

Clean Steel™ .............................................................................................................................. 10

Control Features ........................................................................................................................... 6

Evaporator Fan Motor .................................................................................................................... 8

Fresh Food Control Panel ............................................................................................................. 7

Illustrated Parts Catalog .............................................................................................................. 11

Introduction .................................................................................................................................... 3

Kick Panel ................................................................................................................................... 10

Nomenclature ................................................................................................................................ 5

Schematic ................................................................................................................................... 20

Technical Data ............................................................................................................................... 4

Warranty ...................................................................................................................................... 22

Wiring Diagram ........................................................................................................................... 21

Table of Contents

https://appliancetechmanuals.com

– 4 –

Technical Data

Note: At the temperature control position of

Fresh Food 5, Freezer 5, approximately 90% of

the airflow is distributed in the freezer, 10% in the

Fresh Food.

ELECTRICAL SPECIFICATIONS

Temperature Control (Position 5)....................24.5-12.5°F

Defrost Control ......................................... 8 hrs @ 30 min

Defrost Thermostat .............................................58-28°F

Electrical Rating: 115V AC 60Hz

100V AC 50 Hz .............................................. 6.5 Amp

Maximum Current Leakage ............................... 0.75 mA

Maximum Ground Path Resistance ................0.14 Ohms

Energy Consumption

18' ............................................................40KWH/mo

19' ............................................................41KWH/mo

NO LOAD PERFORMANCE

Control Position, Fresh Food 5, Freezer 5

and Ambient Temperature of: ....................70°F 90°F

Fresh Food, °F .........................................34-40 35-39

Frozen Food, °F ...................................... (-3) -4 (-3) -3

RunTime, % ........................................................... 20-30 41-53

REFRIGERATION SYSTEM

Refrigerant Charge (R134a) ............Refer to Rating Plate

Compressor .................................................. 685 BTU/hr

Minimum Compressor Capacity........................19 inches

Minimum Equalized Pressure

@70°F............................................................ 52PSIG

@90°F............................................................ 66PSIG

REPLACEMENT PARTS

Condenser Fan Motor .................................WR60X10044

Evaporator Fan Motor..................................WR60X10057

Defrost Heater ............................................ WR51X10031

Relay.............................................................WR07X0194

Overload .....................................................WR08X10046

Temperature Control ...................................WR09X10044

Defrost Thermostat .....................................WR50X10025

Capacitor.......................................................WR62X0080

INSTALLATION

Clearance must be provided for air circulation

AT TOP..................................................................1-inch

AT SIDES............................................................1/8-inch

AT REAR................................................................1-inch

CONDENSER

LOOP

PROCESS

TUBE

DRYER

103-02A

AIR FLOW SEALED SYSTEM

Evaporator Fan

Blade Location

Condenser Fan

Blade Location

WARMER AIRMIXED AIR

COLD AIR

DAMPER

FAN

EVAPORATOR

0.35"

0.2"

https://appliancetechmanuals.com

– 5 –

Nomenclature

G T H 1 8 K B P A R W W

BRAND/

PRODUCT

G = GE

H = HOTPOINT

P = PROFILE (GE)

E = ETERNA (GE)

S = SELECT (GE)T

DEPTH/POWER

C = CUSTOM STYLE

F = HIGH GLOSS

SMOOTH FINISH

H = ENERGY STAR

I = CUSTOM STYLE W/

INSTALLED TRIM

L = CLEAN STEEL™

R = RECESSED HANDLE

S = STANDARD

W = FULL WRAP STAINLESS

Z = STAINLESS INTERIOR

INTERIOR/SHELVES

A = LEADER WIRE

B = STANDARD WIRE

C = UPGRADE WIRE

D = DELUXE WIRE

E = PREMIUM WIRE

F = SUPERIOR WIRE

G = STANDARD GLASS

H = UPGRADE GLASS

I = DELUXE GLASS

J = SPILL-PROOF GLASS

K = SPILL-PROOF GLASS

L = SPILL-PROOF SLIDE-OUT GLASS

M = SPILL-PROOF/SLIDE-OUT GLASS

N = SPILL-PROOF/SLIDE-OUT

CUSTOM COOL GLASS

S = STAINLESS STEEL DOORS

ICEMAKER/EXTERIOR

A = NOT ICE MAKER READY

B = ICE MAKER READY

C = FACTORY ICE MAKER

D = CUBED ICE/WATER

E = CUBED/CRUSHED ICE/WATER

F = 6 MO. FILTER/CUBED/CRUSHED ICE

G = 1 YR. FILTER/CUBED/CRUSHED ICE

I = IN-LINE FILTER/INDICATOR & C/C/W

J = IN-LINE FILTER/REFRESHMENT CTR

S = STAINLESS STEEL

EXTERIOR COLOR

AA = ALMOND/ALMOND

AD = ALMOND BLACK

BB = BLACK/BLACK

BS = STAINLESS/BLACK

CC = BISQUE/BISQUE

CT = BISQUE/BLACK

SS = STAINLESS/STAINLESS

WH = WHITE/BLACK

WS - STAINLESS/WHITE

WW = WHITE/WHITET

CONFIGURATION

A = SINGLE DOOR DEFROST

C = CUSTOM STYLE

EXPORT

E = COMBI CYCLE DEFROST

G = COMBI NO-FROST

I = CUSTOM STYLE W/TRIM

EXPORT

Q = MULTI-DOOR

S = SIDE-BY-SIDE CUBIC FEET

MODELYEAR

P = 2003

ENGINEERING

NOMENCLATURE

K = CONVERSION KIT

DOORTYPE

F = FLAT DOOR (G-LINE)

(SPACE = FLAT DOOR (S- & T-LINE

K = RETROFIT DOOR

2003 Upgrade, Louisville Built, No Frost Top Freezer, 18-19 Cu. Ft. Refrigerator

Mini-Manual Location

(Taped to lower back

panel of the refrigerator.)

https://appliancetechmanuals.com

– 6 –

Control Features

1. Refrigerator Control

Turn the ADJUST REFRIGERATOR control from

9 (HIGHEST) to 0 (OFF) to adjust refrigerator

temperature.

2. Freezer Control

Turn the ADJUST FREEZER control from 0 (OFF)

to 9 (HIGHEST) to adjust freezer temperature (5

is NORMAL).

Note: There is no ADJUST FREEZER control

included on the Hotpoint model. Freezer air

distribution is fixed by the position of the baffle

plate. If the freezer air should need to be adjusted

on the Hotpoint model, it is necessary to adjust

the position of the baffle plate manually (see

Components).

GE Models

Hotpoint Models

https://appliancetechmanuals.com

– 7 –

Components

2. Remove the two screws from the rear of the

control panel housing.

3. Remove the screw from the front center of the

control panel housing.

4. Lower the control panel housing, disconnect

the electrical connector, and remove the

housing.

Hotpoint Models

GE Models

5. Remove the baffle.

Note: There is no ADJUST FREEZER control

included on the Hotpoint model. Freezer air flow is

fixed by the position of the baffle plate. If the

freezer air should need to be adjusted on Hotpoint

models, perform steps 12 through 14.

6. Press back the rear retaining clip and lift up

the shaft.

7. Pull the shaft end from the shaft retaining

hole.

8. Press back the forward retaining clip and lift

up the control rod shaft.

9. Remove the control rod shaft and knob.

10. Remove the thermostat retaining block.

Screw

Connector

Baffle

Freezer Control

(Continued next page)

Fresh Food Control Panel

Removal and Replacement

1. Unplug the refrigerator to disconnect power.

Note: The controls on the refrigerator will look like

one of the following:

https://appliancetechmanuals.com

– 8 –

Note: There is no ADJUST FREEZER control

included on the Hotpoint model. Freezer air

distribution is fixed by the position of the baffle

plate. If the freezer air should need to be adjusted

on Hotpoint models, perform steps 12 through 14.

(Steps 12 through 14 should only be used if all

other temperature checks have been performed

and a temperature problem still exists.)

11. Remove the baffle plate from the baffle.

12. Trim the edge of the baffle plate to fit in either

the MID or COLD baffle plate slots.

13. To increase freezer temperature slide the

baffle plate into the WARM slot.

Note: Inserting the baffle plate into the WARM

slot will raise freezer temperature between 3 and

4°F, and lower fresh food temperature between 3

and 4°F.

14. To decrease freezer temperature slide the

baffle plate into the COLD slot.

Note: Inserting the baffle plate into the COLD slot

will lower freezer temperature between 3 and 4°F,

and raise fresh food temperature between 3 and

4°F.

Retaining Block

Front Clip Shaft Rear Clip

Plate

Baffle

COLD

WARM

MID

Baffle

Plate

Shelf

Shield

Shelf Supports

Evaporator Fan Motor

Removal and Replacement

1. Unplug the refrigerator to disconnect power.

2. Lift up the left side of the shelf and slide it left

into the center of the shelf supports.

3. Rotate the right side of the shelf up and out of

the shelf supports and remove the shelf.

4. Remove the ice maker if installed.

5. Squeeze the top and bottom of the light shield

and pull the shield from the evaporator cover.

6. Remove the light bulb from the socket.

https://appliancetechmanuals.com

– 9 –

10. Remove the two screws from the evaporator

cover.

11. Remove the two screws from the fan bracket

and pull the evaporator cover forward.

Note: If necessary, bow the evaporator cover

outward until it clears the ice maker receptacle.

12. Depress the clip and pull the socket out far

enough to access the electrical connector.

Note: If necessary, reach behind the evaporator

cover to access the electrical connector.

13. Disconnect the electrical connector from the

light socket and remove the socket.

14. Remove the evaporator cover.

15. Disconnect the electrical connector from the

evaporator fan motor.

16. Slide the evaporator fan blade off the motor

shaft.

20. Make sure the rear blue isolation grommet is

seated properly on the motor mounting

bracket prior to installation of the new

evaporator fan motor.

17. Remove the evaporator fan motor screws and

grounding wire from the evaporator fan

bracket.

18. Remove the front evaporator fan bracket and

motor.

19. Remove and retain the front blue isolation

grommet from the motor shaft.

Screw Screw

7. Remove the 2 screws from the bottom of the

tower housing.

8. Lift up and pull the tower housing forward,

making sure the bottom notch comes out of

and clears the freezer floor.

9. Remove the tower housing.

Tower Housing

Screw

Socket

Clip

Screw Electrical

Connector

Evaporator Cover

Blade

Electrical

Connector

Bracket

Screw

Screw and

Ground Wire

Grommet

https://appliancetechmanuals.com

– 10 –

6. Reverse the above procedure to reinstall.

7. Remove the 3 screws and right mobility

assembly.

8. Remove the 3 screws and left mobility

assembly.

9. Slide out and remove the kick panel.

Note: When installing the kick panel screws, use

of an electric screwdriver will aid in the

installation.

Note: If necessary, adjust the mobility screw to

remove the mobility assembly in steps 7 and 8.

Hinge Screws

Top Screw

Kick Panel

Level Adjustment Screw

Kick Panel

The kick panel on models with no-freezer light is

replaceable.

Note: The kick panel on models with a freezer

light is replaceable, but not currently cataloged.

Removal and Replacement

Note: This procedure should be performed by two

people.

1. Unplug the refrigerator to disconnect power.

2. Remove shelving from the refrigerator and

freezer.

3. Lay the refrigerator on it's back.

4. Remove the 2 hinge screws, hinge, and fresh

food door from the refrigerator.

5. Remove the top screw from the same side.

6. Remove the 3 screws from the opposite side

of the kick panel.

Clean Steel™

Clean Steel™ is a vinyl-laminated steel similar in

appearance to true stainless steel. Clean Steel™

is easier to clean than stainless steel and does

not show fingerprints. The material has better

scratch resistance and has a galvanized steel

substrate to prevent red rust should a scratch

occur. Doors are shipped with a protective

polyethylene coating to help eliminate/reduce any

damage in shipping and delivery to the customer.

A touch-up paint is being developed for noncritical

areas, but there is currently no appearance repair

method for the front face of the door.

A Clean Steel™ surface is cleaned the same way

as our current painted surfaces. Use a clean

cloth lightly dampened with appliance polish or

mild household detergent. Then, use another

clean cloth to dry and polish the cleaned surfaces.

Caution: On all painted appliance surfaces, do

not use a kitchen towel that has been previously

used for kitchen cleaning without first being

washed. Bacteria from the previously used towel

will be deposited on the surface of the appliance

and will deteriorate the finish.

Screw

Mobility Assembly

https://appliancetechmanuals.com

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere GE Kühlschrank Handbücher

GE PSIC5RGX - Profile: 24.6 cu. Ft Handbuch

GE GSS25LSWJSS and Sicherheitsleitfaden

GE PSC23MSWSS - Profile: 23.3 cu. Ft Handbuch

GE Profile PDCS1NBX Bedienungsanleitung

GE PFSF2MJYBB - Profile 22.2 cu. Ft.... Handbuch

GE PYE23KSDSS Montageanleitung

GE ZIS360NXD Bedienungsanleitung

GE Profile Series Betriebsanleitung

GE GTR12 and Betriebsanleitung

GE PFSS6SMX - Profile: 25.8 cu. Ft.... Handbuch

GE AJCH 12 Betriebsanleitung

GE TFJ20JA Bedienungsanleitung

GE PFS22SISBSS Bedienungsanleitung

GE Profile PSCS3RGXSS Bedienungsanleitung

GE GE Profile Arctica PTS22LBN Gebrauchsanweisung

GE GDSL3KCYRLS - R 22.9 Cu. Ft. Bottom-Freezer Drawer... Handbuch

GE GTE21GTHWW Betriebsanleitung

GE Monogram ZIC360NXRH Bedienungsanleitung

GE SIDE-BY-SIDE REFRIRATOR 22 Reparaturanleitung

GE GTS18JCP Bedienungsanleitung

GE GTH17BBCRWW Montageanleitung

GE SIDE-BY-SIDE REFRIRATOR 22 Bedienungsanleitung

GE PSCS3TGXSS - 23.3 cu. ft. Refrirator Handbuch

GE GBC12IAX Betriebsanleitung

Beliebte Kühlschrank Handbücher anderer Marken

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Bedienungsanleitung

Sharp

Sharp SJ-BA31IEXW2-EU Bedienungsanleitung

CORBERO

CORBERO CC2300MCW Bedienungsanleitung

KitchenAid

KitchenAid 2205264 Bedienungsanleitung

NEFF

NEFF KI181 Series Bedienungsanleitung

Hoshizaki

Hoshizaki Reach-In Bedienungsanleitung

Amana

Amana ASD2524VES00 Bedienungsanleitung

BOMANN

BOMANN KGC 213 Bedienungsanleitung

Danby

Danby DAR044A1SLDD Montageanleitung

Beko

Beko CSA31022 Bedienungsanleitung

IKEA

IKEA FROSTIG C 185 E Bedienungsanleitung

Electrolux

Electrolux ER 6821 D Bedienungsanleitung

True

True TS-28 Bedienungsanleitung

Frigidaire

Frigidaire FSC23R5DW9 Bedienungsanleitung

Beko

Beko LSP4579W Bedienungsanleitung

Teledyne

Teledyne 6712FR and Betriebsanleitung

Matsui

Matsui MTT50W12E Bedienungsanleitung