GE Monogram ZFSB27DYSS Bedienungsanleitung

GE Monogram®

Installation

Instructions

Stainless Steel

Refrigerator

Model

ZFSB27DY SS

Tools

Required

• Bucket • Tubing cutter • Drill and appropriate bits

• Safety glasses • Tin snips

Materials

Required

Flooring For proper installation, this refrigerator must be placed on a level surface of hard material that

is at the same height as the rest of the flooring. This surface should be strong enough to

support a fully loaded refrigerator.

CAUTION: Protect the finish of the flooring. Cut a large section of the cardboard carton and

place under the refrigerator while you are working.

Contents Installation Preparation

Water Connection Location, Electrical...................... 3

Product Dimensions & Clearances............................. 3

Grounding the Refrigerator ....................................... 4

Installation

Step 1, Remove Packaging .......................................... 5

Step 2, Install Water Line............................................ 6

Step 3, Connect Water Supply.................................... 6

Step 4, Connect Power ................................................ 7

Step 5, Start Icemaker ................................................. 7

Step 6, Roll Refrigerator into Position....................... 7

Step 7, Level The Refrigerator ................................... 7

Before you begin—Read these instructions completely and carefully.

IMPORTANT: Save these instructions for local inspector’s use.

IMPORTANT: OBSERVE ALL GOVERNING CODES AND ORDINANCES.

NOTE TO INSTALLER: Be sure to leave these instructions with the

Consumer.

NOTE TO CONSUMER: Keep these instructions with your Use and Care

Book for future reference.

• Water shut-off valve • Water filter • Copper tubing

(recommended) WR97X0214 • 1/4" O.D. Compression nuts

(recommended) and 2 ferrules (sleeves)

Installation Preparation

Stainless Steel Refrigerator

Water

Connection

Location,

Electrical

The water line can be routed through

the floor or through an adjacent cabinet, as

close to the back wall as possible.

A 115 volt, 60 Hz. 15 or 20 amp power supply

is required. An individual properly grounded

branch circuit or circuit breaker is recom-

mended, as noted on the rating plate. The

rating plate is located on the bottom of the

cabinet front of the fresh food compartment

and is visible when the door is opened.

Through floor

to basement

cold water pipe

Under sink

to cold

water pipe

Through wall to

utility room cold

water pipe

In crawl

space under

house

Product

Dimensions

& Clearances

This monogram free-standing refrigerator

requires the following clearances for proper

air circulation, plumbing and electrical

connections.

Sides ................................ 5/8"

Top ..................................... 1"

Back ................................... 1"

If the refrigerator is to be installed in a corner:

• A 1-1/2" clearance between the case trim

and the adjacent wall on both sides of the

refrigerator will assure a 90°door opening

and access to all drawers.

• Allow 11-1/4" clearance on the freezer side

for removal of ice bin.

• On the fresh food side, drawers can be

removed by first disassembling door bins.

Or, allow 14" clearance to remove drawer

without disassembling the door bins.

36"

71"

35"

Including

Handles

32-1/2"

Case

Depth

Installation Preparation

Stainless Steel Refrigerator

Grounding

the

Refrigerator

IMPORTANT - (Please read carefully)

FOR PERSONAL SAFETY, THIS APPLIANCE

MUST BE PROPERLY GROUNDED.

The power cord of this appliance is equipped

with a three-prong (grounding) plug which

mates with a standard

three-prong (grounding)

wall receptacle to minimize

the possibility of electric

shock hazard from this

appliance.

Have the wall outlet and circuit checked by a

qualified electrician to make sure the outlet is

properly grounded.

Where a standard 2-prong wall outlet is encoun-

tered, it is your personal responsibility and

obligation to have it replaced with a properly

grounded 3-prong wall outlet.

DO NOT, UNDER ANY CIRCUMSTANCES,

CUT OR REMOVE THE THIRD (GROUND)

PRONG FROM THE POWER CORD.

Use of Adapter plug

Because of potential hazards under certain

conditions, we strongly recommend against

use of an adapter plug. However, if you still

elect to use an adapter, where local codes

permit, a TEMPORARY CONNECTION, may

be made to a properly grounded 2-prong wall

outlet by use of a UL listed adapter available

at most hardware stores.

The larger slot in the adapter must be aligned

with the larger slot in the wall outlet to

provide proper polarity in the connection of

the power cord.

Use of an adapter plug will increase the

clearance needed for the back of the refrig-

erator.

CAUTION: Attaching the adapter ground

terminal to a wall outlet cover screw does not

ground the appliance unless the cover screw is

metal, and not insulated, and the wall outlet is

grounded through the house wiring. You

should have the circuit checked by a qualified

electrician to make sure the outlet is properly

grounded.

When disconnecting the power cord from the

adapter, always hold the adapter in place with

one hand and pulling the power cord with the

other hand. If this is not done, the adapter

ground terminal is very likely to break with

repeated use.

Should the adapter ground terminal break, DO

NOT USE the appliance until a proper ground

has again been established.

Use of Extension Cords

Because of potential safety hazards under

certain conditions, we strongly recommend

against the use of an extension cord. However, if

you still elect to use an extension cord, it is

absolutely necessary that it be a UL listed 3-wire

grounding type appliance extension cord

having a grounding type plug and outlet and

that the electrical rating of the cord be 15

amperes (minimum) and 120 volts.

Align Large Prongs/Slots

Insure Proper Grounding and Firm

Connection Exists Before Use

Installation

Stainless Steel Refrigerator

Step

Remove

Packaging

To remove the freezer door:

Open the freezer door and remove the base

grille.

E. Plastic tubing enters the freezer door

through the bottom hinge. Remove the

tubing clamp and loosen the coupling nut.

•Pull the tubing away from the coupling

and close the door.

F. Loosen the screw at the top of the door

hinge. Disconnect the wiring harness

connector.

•Hold the door closed and remove the

bottom hinge screws.

•Remove the door together with both

hinges to avoid damage to the wiring

harness or water tubing.

To move the refrigerator indoors:

•Place a piece of the carton against the side

panel of the refrigerator as a pad to protect

the stainless steel finish.

•Place the refrigerator on the hand-truck with

a side panel against the truck.

•Replace the refrigerator doors and top cap

following the same procedures in reverse

order. Be sure to replace the screws on the

back side under the top cap.

CAUTION

To remove top cap:

A. On the back side of the refrigerator,

remove 1 screw located under the top cap

on each side. IMPORTANT: These screws

must be re-installed when top cap is re-

placed.

B. Push the top cap forward, slipping the cap

through key hole slots, lift off cap.

C. Remove 2 screws on the top of the refrig-

erator case and lift off cap filler strip.

To Remove the Fresh Food Door:

D.On the fresh food side, loosen the screw at

the top of the door hinge. Carefully lift off

door.

Use a hand-truck to move this refrigerator.

•To remove the skid, lay the refrigerator on its

back and remove the shipping bolts.

Before moving the refrigerator indoors:

• Cut the banding with tin snips.

• Remove outer carton.

• Slide out 4 corner posts.

• Remove plastic wrapping.

Door and passageways

into the installation location require a 36"

min. opening.

If the opening is less than 36", the top cap

and doors must be removed.

Loosen 

This Nut

Spring

Clamp

Coupling

Wiring

Connector

Installation

Stainless Steel Refrigerator

Install

Water Line

Step

Washer

Inlet End

Vertical Cold

Water Pipe

Saddle Type

Shutoff

Valve

Pipe Clamp

Saddle Type

Shutoff Valve

Compression Nut

Ferrule

(Sleeve)

Outlet Valve

Packing Nut

•A cold water supply is required for automatic

icemaker operation. The water pressure must

be between 20 and 120 p.s.i.

•Route 1/4" OD copper tubing between house

cold water line and the water connection

location.

•Measure the distance from the water valve on

the back of the refrigerator to the water

supply line. Add 8 foot length to allow the

refrigerator to be moved away from the wall

after installation. Bend the tubing into 3 coils

of about 10".

Shut off the main water supply.

Turn on the nearest faucet long enough to

clear the line of water.

Install a shut-off valve between the icemaker

water valve and cold water pipe in a basement

or cabinet. The shut-off valve should be

located where it will be easily accessible.

NOTE: If you must install the valve into a

horizontal water pipe, make the connection at

the top or side, rather than at the bottom, to

avoid drawing off any sediment from the water

pipe.

•Drill a 1/4" hole in the water pipe.

•Fasten the shut-off valve to the pipe with pipe

clamp.

•Tighten the clamp screws until the sealing

washer begins to swell. Do not over tighten.

•Place a compression nut and ferrule (sleeve)

onto the end of the tubing and connect it to

the shut-off valve. Make sure the tubing is

fully inserted into the valve and ferrule is

tightened.

•Turn on the main water supply and flush

debris from the line. Run about a quart of

water through the tubing into a bucket. Shut

off water supply at the shut-off valve.

NOTE: Saddle type shut-off valves are

included in many water supply kits. Before

purchasing, make sure a saddle type valve

complies with your local plumbing codes.

•Install optional water filter in the water line

near the refrigerator. A water filter is

recommended in areas where water supply

contains sand or particles. Installation

instructions are packed with the filter.

Step

Connect

Water Supply

Check to be sure that refrigerator power cord

is not plugged into the wall outlet.

•Remove the plastic flexible cap from the

water valve.

•Place compression nut and ferrule (sleeve)

onto the end of the tubing as shown.

•Insert the end of the copper tubing into the

water valve connection a far as possible. Hold

the tubing in place and tighten the fitting.

•Fasten the copper tubing into the clamp

provided to hold it in a vertical position. You

may need to pry open the clamp.

•Turn on the water at the shut-off valve to

check for leaks.

1/4" Copper Tubing Tubing

Clamp

Ferrule

(Sleeve)

1/4" Compression Nut

Refrigerator Connection

Installation

Stainless Steel Refrigerators

Step

Connect

Power

The icemaker will not begin to operate until it

reaches its operating temperature of 15ºF.

(-9ºC.) or below.

•Lower the feeler arm to the ON position and

the icemaker will begin operation

automatically.

•Make sure the ice bin is pushed back all the

way to the stops on the shelf below the

icemaker.

•Discard the first few batches of ice cubes to

be sure that any remaining impurities in the

water line will be flushed out.

NOTE: The icemaker may double-cycle when

it first starts, causing some water spillage from

the icemaker into the ice bucket. This is

normal and should not happen again.

Step

Start

Icemaker

•Push the refrigerator into position being

careful not to entangle power cord. Arrange

the coil of copper tubing so that is does not

vibrate against the back of the refrigerator.

•Remove internal packing materials and set

shelves to desired positions.

Roll

Refrigerator

Into Position

Step

Level The

Refrigerator

Step

•Remove the base grille by gasping it at the

bottom and pulling outwards.

•Turn the roller adjusting screws clockwise to

raise the refrigerator, counterclockwise to

lower it. Use an adjustable wrench (3/8" hex

head bolt) or pliers.

NOTE: When leveling, you can improve door

closure by raising the front approximately

5/8" from the floor.

•Replace base grille by aligning prongs with

clamps on the cabinet and pushing forwards

until the grille snaps into place.

Clamp

Prong

•Connect the refrigerator power cord plug to

properly grounded receptacle.

Pub. No. 49-6894

Dwg. No. 162D9886P001

 1996 GE Appliances

Printed in USA

(N.D. 523) 9/96

Note: While performing installations described in this book,

safety glasses or goggles should be worn.

To obtain specific information concerning any

Monogram product or service, call GE Answer Center®

consumer information service at 800.626.2000—any

time, day or night.

For Monogram local service in your area, call

1-800-444-1845.

NOTE: Product improvement is a continuing endeavor at General

Electric. Therefore, materials, appearance and specifications are subject

to change without notice.

Monogram.

General Electric Company

Louisville, KY 40225

Inhaltsverzeichnis

Andere GE Kühlschrank Handbücher

GE Profile PSB42LGR Handbuch

GE SIDE-BY-SIDE REFRIRATOR 22 Sicherheitsleitfaden

GE GSH25ISX Handbuch

GE TURBOCOOL 23 Sicherheitsleitfaden

GE Profile PSDS3YGXSS Bedienungsanleitung

GE GTH17DBDCC Montageanleitung

GE Profile ENERGY STAR PDS20MFS Handbuch

GE TFX27FM Bedienungsanleitung

GE Profile PDS20MBS Bedienungsanleitung

GE Monogram ZIK30GNZAII Bedienungsanleitung

GE GBC12IAXLSS Betriebsanleitung

GE GTS22JBPARCC and Betriebsanleitung

GE Profile PSS26PSWSS Bedienungsanleitung

GE Profile PFCF1PJY Handbuch

GE GTS21KBXBB - 21 cu. Ft. Top Freezer... Montageanleitung

GE CZS25TSESS Montageanleitung

GE Profile PSCF3RGX Bedienungsanleitung

GE Monogram ZIC360NHLH Bedienungsanleitung

GE GSS20DBTWW - 19.9 cu. Ft. Refrigerator Handbuch

GE MONOGRAM ZICS360NMLH Handbuch

GE PZS25KSESS Montageanleitung

GE Bottom-Freezer Built-In Refrigerator Bedienungsanleitung

GE GSF25IGZ Handbuch

GE Profile PCF25PGT Sicherheitsleitfaden

Beliebte Kühlschrank Handbücher anderer Marken

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Bedienungsanleitung

Sharp

Sharp SJ-BA31IEXW2-EU Bedienungsanleitung

CORBERO

CORBERO CC2300MCW Bedienungsanleitung

KitchenAid

KitchenAid 2205264 Bedienungsanleitung

Stengel

Stengel KU 1101 A++ Bedienungsanleitung

NEFF

NEFF KI181 Series Bedienungsanleitung

Hoshizaki

Hoshizaki Reach-In Bedienungsanleitung

Amana

Amana ASD2524VES00 Bedienungsanleitung

BOMANN

BOMANN KGC 213 Bedienungsanleitung

Danby

Danby DAR044A1SLDD Montageanleitung

Samsung

Samsung RF323TE Bedienungsanleitung

Beko

Beko CSA31022 Bedienungsanleitung

IKEA

IKEA FROSTIG C 185 E Bedienungsanleitung

Electrolux

Electrolux ER 6821 D Bedienungsanleitung

True

True TS-28 Bedienungsanleitung

Frigidaire

Frigidaire FSC23R5DW9 Bedienungsanleitung

Beko

Beko LSP4579W Bedienungsanleitung