GE Spacemaker GMR06AAZ Originalbetriebsanleitung

49-60642 08-10 GE

GEAppliances.com

Write the model and serial numbers here:

Model # __________________________

Serial # __________________________

Find these numbers on a label inside

the refrigerator on the side wall.

Refrigerators

2 Cubic Foot Models

3 Cubic Foot Models

4 Cubic Foot Models

6 Cubic Foot Models

Owner’s Manual

& Installation

Instructions

Safety Information . . . . . . . .2, 3

Operating Instructions

Care and Cleaning . . . . . . . . . .6–8

Control Settings . . . . . . . . . . . . . .4

Refrigerator Features . . . . . . . . . .5

Replacing the Light Bulb . . . . . . .6

Installation Instructions . . .9–11

Troubleshooting Tips . . . .12, 13

Consumer Support

Consumer Support . . .Back Cover

Warranty . . . . . . . . . . . . . . . . . . .15

ATTENTION:

Defrosting—Do not use sharp, pointed

objects to remove frost or ice from

surfaces of the freezer compartment.

Doing so could puncture the cooling

coil, causing the unit to lose its ability

to maintain cold temperatures and

voiding the warranty. See the Care and

Cleaning section for instructions on

defrosting the freezer compartment.

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

Safety InstructionsOperating Instructions

Troubleshooting Tips

Consumer Support Installation Instructions

DANGER! RISK OF CHILD ENTRAPMENT

WARNING!

Use this appliance only for its intended purpose as described

in this Owner’s Manual.

This refrigerator must be properly

installed and located in accordance

with the Installation Instructions

before it is used.

Do not allow children to climb,

stand or hang on the shelves

in the refrigerator. They could

damage the refrigerator and

seriously injure themselves.

Do not store or use gasoline or

other flammable vapors and

liquids in the vicinity of this or

any other appliance.

Before replacing a burned-out

light bulb, the refrigerator should

be unplugged in order to avoid

contact with a live wire filament.

(A burned-out light bulb may

break when being replaced.)

Keep fingers out of the “pinch

point” areas; clearances between

the doors and cabinet are

necessarily small. Be careful closing

doors when children

are in the area.

Unplug the refrigerator before

cleaning and making repairs.

NOTE: We strongly recommend

that any servicing be performed by

a qualified individual.

Turning the temperature control

dial to the OFF position stops

cooling but does not shut off

power to the refrigerator.

When using electrical appliances, basic safety precautions

should be followed, including the following:

SAFETY PRECAUTIONS

Child entrapment and suffocation

are not problems of the past. Junked

or abandoned refrigerators are still

dangerous… even if they will sit for

“just a few days.” If you are getting

rid of your old refrigerator, please

follow the instructions below to help

prevent accidents.

Before You Throw Away Your

Old Refrigerator or Freezer:

Take off the doors.

Leave the shelves in place so that

children may not easily climb

inside.

Refrigerants

All refrigeration products contain

refrigerants, which under federal law

must be removed prior to product

disposal. If you are getting rid of an

old refrigeration product, check with

the company handling the disposal

about

what to do.

PROPER DISPOSAL OF THE REFRIGERATOR

READ AND FOLLOW THIS SAFETY

INFORMATION CAREFULLY.

SAVE THESE INSTRUCTIONS

GEAppliances.com

Safety Instructions Operating Instructions Troubleshooting Tips Consumer SupportInstallation Instructions

USE OF EXTENSION CORDS

Because of potential safety hazards under certain conditions,

we strongly recommend against the use of an extension cord.

However, if you must use an extension cord, it is absolutely necessary that it

be a UL-listed, 3-wire grounding type appliance extension cord having a

grounding type plug and outlet and that the electrical rating of the cord be

15 amperes (minimum) and 120 volts.

HOW TO CONNECT ELECTRICITY

Do not, under any circumstances, cut or remove the third

(ground) prong from the power cord. For personal safety,

this appliance must be properly grounded.

The power cord of this appliance is

equipped with a 3-prong (grounding)

plug which

mates with a standard 3-prong

(grounding) wall outlet to minimize

the possibility of electric shock

hazard from this appliance.

Have the wall outlet and circuit

checked by a qualified electrician to

make sure the outlet is properly

grounded.

If you have only a standard

2-prong wall outlet, it is your

personal responsibility and

obligation to have it replaced with a

properly grounded

3-prong wall outlet.

The refrigerator should always be

plugged into its own individual

electrical outlet which has a voltage

rating that matches the rating plate.

This provides the best performance

and also prevents overloading house

wiring circuits which could cause a

fire hazard from overheated wires.

Never unplug your refrigerator by

pulling on the power cord. Always

grip plug firmly and pull straight out

from the outlet.

Repair or replace immediately all

power cords that have become

frayed or otherwise damaged.

Do not use a cord that shows cracks

or abrasion damage along its length

or at either end.

When moving the refrigerator away

from the wall, be careful

not to roll over or damage the power

cord.

About the control

on the refrigerator.

Control Settings

The temperature control maintains the temperature in the refrigerator.

Setting the control at COOL is the warmest setting. Setting the control at

COLDEST is the coldest setting. Set the control at COLD. (See Fig. 1 or 2)

Allow 24 hours for the refrigerator to reach the desired temperature.

If you want a colder or warmer temperature, move the dial one setting at a

time. Moving the control toOFF stops cooling but does not turn off the

power to the refrigerator. Setting the control too high/one of the Snowflake

positions may cause freezing in the refrigerator depending on the room

temperature.

How To Test Temperatures

Use the milk test. Place a container of milk on a shelf and check it

a day later. If the milk is too warm or too cold, adjust the temperature

control.

After changing the control, allow 24 hours for the refrigerator to reach the

temperature you have set.

The control will look like one of the above.



Safety InstructionsOperating InstructionsTroubleshooting TipsConsumer Support Installation Instructions

Fig. 1

Fig. 2

Safety Instructions Operating Instructions Troubleshooting Tips Consumer SupportInstallation Instructions

Shelves

To remove a shelf, lift up the back slightly and pull forward.

Some models have multi-position shelves that can be moved

to different levels.

Ice Tray Compartment

This compartment is designed for production of ice cubes and short-term

storage (a few days at most) of some commercially-frozen foods when in

contact with the evaporator (cold surface

in compartment.)

Door Shelves

Shelves on the door provide convenient storage for frequently

used items. Some models have doors that are deep enough to

store large bottles.

About the refrigerator features. GEAppliances.com

Key-Ejecting Lock (on some models)

The key for the spring-loaded lock is automatically ejected—

key will not remain in lock in either the open or closed position.

Keep the key out of reach of children and away from the refrigerator.

If a replacement key is needed, it can be ordered by visiting our Website

GEAppliances.com, or calling GE Parts and Accessories, 800.626.2002.

Order part WR05X10006.

Safety InstructionsOperating Instructions

Troubleshooting Tips

Consumer Support Installation Instructions

Cleaning the Outside

Keep the outside clean. Wipe with a clean cloth lightly dampened with

kitchen appliance wax or mild liquid dish detergent. Dry and polish with

a clean, soft cloth.

Do not wipe the refrigerator with a soiled dish cloth or wet towel. These may

leave a residue that can erode the paint. Do not use scouring pads, powdered

cleaners, bleach or cleaners containing bleach because these products can

scratch and weaken the paint finish.

Protect the paint finish. The finish on the outside of the refrigerator

is a high quality, baked-on paint finish. With proper care, it will

stay new-looking and rust-free for years. Apply a coat of kitchen/

appliance wax when the refrigerator is new, and then at least

twice a year.

Cleaning the Inside

To help prevent odors, leave an open box of baking soda in the

refrigerator.

Unplug the refrigerator before cleaning. If this is not practical,

wring excess moisture out of sponge or cloth when cleaning

around the control.

Use warm water and baking soda solution–about a tablespoon

(15 ml) of baking soda to a quart (1 liter) of water. This both

cleans and neutralizes odors. Rinse and wipe dry.

Other parts of the refrigerator–including door gaskets, fruit

and vegetable drawers, and all plastic parts–can be cleaned

the same way.

Do not wash any plastic refrigerator parts in the dishwasher.

Care and cleaning

of the refrigerator.

Replacing the Light Bulb (on some models)

Unplug the refrigerator before replacing a burned-out bulb. Setting the

controls to OFF does not remove power to the light circuit.

The light bulb is located behind the temperature control housing and is

visible through the slots in the housing.

Reach up through the opening at the bottom of the control housing and

gently unscrew the light bulb. Replace with a bulb

of the same or lower wattage.

Using a Philips screwdriver, unscrew the lens and pull horizontally until

the lens is removed. Gently unscrew the light bulb and replace with a

bulb of 15 watts or less.

Safety Instructions Operating Instructions Troubleshooting Tips Consumer SupportInstallation Instructions

Defrosting

(on push button defrost models only)

Defrost whenever frost on the wall of the ice tray compartment becomes

1/4”thick.

To defrost:

Remove foods and ice trays from the refrigerator and ice tray

compartment.

Ensure drip tray is below ice tray compartment to collect water.

Push in the red “Defrost Button” located in the center of the

temperature control dial. Defrost cycle will start immediately. NOTE:

Turning the temperature control dial to the OFF position

is not required.

Defrosting usually takes a few hours. When defrosting is complete, the red

“Defrost Button” will release automatically. Then the refrigerator will

resume normal operation while moving towards the set temperature.

NOTE: After defrosting, allow a few hours to reach the set temperature

before making any further adjustments.

To defrost faster, keep the door open. Also, pouring warm (not hot) water

on the frosted part may speed defrosting. Do not use boiling water—it

may damage plastic parts.

CAUTION: If you decide to “speed up” the defrost cycle by manually

removing ice, NEVER use a sharp or metallic instrument to chip away

the ice as it may damage the cooling coils. (A punctured cooling coil will

cause serious problems and void the warranty.) Do no use any electrical

device in defrosting your refrigerator.

After defrosting:

After red “Defrost Button” has released, empty water from the drip

tray. Wash the tray with warm water. Dry the drip tray completely.

Wipe the ice tray compartment with a damp cloth.

Return drip tray to below ice tray compartment.

Return food and ice trays to the refrigerator and close the door.

IMPORTANT: If the red “Defrost Button” is pushed accidentally,

it can not be manually released. The defrost cycle will run until complete.

To speed up the defrost cycle, remove the drip tray and apply a warm

damp cloth against the temperature sensing wire located on the underside

of the ice tray compartment. After several minutes, the heat from the

warm cloth will raise the temperature of the thermostat, causing the

defrost cycle to end and releasing the red “Defrost Button.” The

refrigerator will then resume normal operation.

NOTE: If ice buildup is very thick, it may keep the ice tray compartment door

from opening or closing completely. Don’t try to force it open or closed; after

defrosting, the door will open and close easily.

GEAppliances.com

Defrost push

button

Temperature

sensing wire

Safety InstructionsOperating Instructions

Troubleshooting Tips

Consumer Support Installation Instructions

Care and cleaning of the refrigerator.

Preparing for Vacation

For long vacations or absences, remove food and unplug the refrigerator.

Move the control to the OFF position, and clean the interior with a baking

soda solution of one tablespoon (15 ml) of baking soda to one quart (1

liter) of water. Leave the door open.

Preparing to Move

Secure all loose items such as shelves and ice trays by taping them

securely in place to prevent damage.

Be sure the refrigerator stays in an upright position during moving.

Defrosting

(on manual defrost models only)

Defrost whenever frost on the wall of the ice tray compartment becomes

1/4”thick. Never use a sharp or metallic instrument to remove frost as

it may damage the cooling coils. (A punctured cooling coil will cause

serious problems and void the warranty.) We recommend using a plastic scraper.

Do not use any electrical device in defrosting your refrigerator.

To defrost:

Remove foods and ice trays from the ice tray compartment.

Set the temperature control dial to 0.

On models without a drip tray, place a pan beneath the ice tray

compartment to collect water.

Defrosting usually takes a few hours. To defrost faster, keep the

door open. Also, pouring warm (not hot) water on the frosted part may

speed defrosting. Do not use boiling water—it may damage

plastic parts.

After defrosting:

Empty water from the drip tray or from the pan placed beneath the ice

tray compartment. Wash the tray or pan with warm water.

Wipe the ice tray compartment with a damp cloth.

Turn the temperature control to the desired setting and

return food and ice trays to the refrigerator.

NOTE: If ice buildup is very thick, it may keep the ice tray compartment door

from opening or closing completely. Don’t try to force it open; after defrosting, the

door will open and close easily.

Preparing to install

the refrigerator. GEAppliances.com

Read these instructions completely and carefully.

Turn counterclockwise to raise,

clockwise to lower.

Refrigerator Location

Do not install the refrigerator where the temperature will go below 50°F

(10°C) because it will not run often enough to maintain proper

temperatures.

Install it on a floor strong enough to support it fully loaded.

If the 2 cubic foot model is placed on a countertop or stand,

the front surface of the door should be 3”or more back from the edge of

the countertop or stand to avoid accidental tipping of the appliance

during normal use.

Do not install it closer than 5”(13 cm) from range.

The following applies only to the 2, 3 and 4 Cubic Foot Models:

Do not install it in a recessed area.

Do not build in the refrigerator.

Clearances

Allow the following clearances for ease of installation and proper

air circulation.

2, 3 and 4 6 Cubic Foot

Cubic Foot Models Model only

Sides 1/2”(13 mm)0”(0mm)*

Top 2”(51 mm) 0”(0mm)

Back 2”(51 mm)** 1”(25 mm)

*1-1/4”(32 mm) for hinge side clearance

**From the rear cabinet surface to the wall

Leveling Legs (on some models)

Adjustable legs at the front corners of the refrigerator

should be set so the refrigerator is firmly positioned on the

floor and the front is raised just enough that the door closes

easily when opened about halfway.

To adjust the leveling legs, turn the legs counterclockwise

to raise the refrigerator, clockwise to lower it.

Safety Instructions Operating Instructions Troubleshooting Tips Consumer SupportInstallation Instructions

Safety InstructionsOperating InstructionsTroubleshooting TipsConsumer Support Installation Instructions

Leveling legs

Bottom

hinge

Plug button

Spacer

Hinge cover

Plug buttons

or screws Hinge

Preparing to install the refrigerator.

Door Reversal

(on some models)

1. Remove the small plug button on the left

side of the door top cap.

2. Remove the 3 (2 on some models) plug

buttons or screws on the left side on top of

the cabinet.

3. Remove the plastic hinge cover by lifting it

up by the front edge. Some models also

require removal of a screw.

4. Remove the 3 (2 on some models) screws

from the top hinge.

5. Lift the door up and off the bottom hinge

(right side).

6. Tilt the refrigerator cabinet back to remove

the right leveling leg.

7. Remove the screws on the bottom hinge

(right side) and remove the leveling legs.

Move the bottom hinge to the left side and

secure it with screws. Re-install the leveling

legs.

IMPORTANT: The left leg has a spacer or

spacer feature that must be moved to the right

side leveling leg when the door swing is

reversed.

8. Screw the right leveling leg, with the spacer

in place, back in place on the right side.

9. Position the door on the left bottom hinge.

With the magnetic gasket holding the door

in place, secure the top hinge with screws.

10. Make sure the door is aligned with the

refrigerator cabinet before continuing.

11. Replace the hinge cover on top of

the hinge.

12. Put the plug button in the hole on the right

side of the door cap.

13. Put the 3 (2 on some models) plug buttons

on the right side on top of the cabinet

Andere Handbücher für Spacemaker GMR06AAZ

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere GE Kühlschrank Handbücher

GE Profile PSCF5RGXBB Service-Handbuch

GE GE Profile Arctica CustomStyle PSI23NCP Gebrauchsanweisung

GE PTS18SHSSS Montageanleitung

GE Bottom-Freezer Built-In Refrigerators Bedienungsanleitung

GE 200D8074P036 Sicherheitsleitfaden

GE Profile PCF23MGW Handbuch

GE ENERGY STAR GTH18ECBWW Handbuch

GE PYE23PSDSS Handbuch

GE TA10 Bedienungsanleitung

GE Monogram ZIC360NX Bedienungsanleitung

GE Profile PSHS6YGZSS Handbuch

GE Profile Arctica PSC23SHM Gebrauchsanweisung

GE Profile PFS22MBW Handbuch

GE Spacemaker GMR06AAPWW Gebrauchsanweisung

GE GTE18GSH Handbuch

GE 20 Betriebsanleitung

GE Bottom-Freezer Built-In Refrigerator Bedienungsanleitung

GE PTS25LBMBRBB and Betriebsanleitung

GE GZS23HSESS Montageanleitung

GE PFE29 Betriebsanleitung

GE RHM 15 Betriebsanleitung

GE ESS25LSQASS Sicherheitsleitfaden

GE PSS25MCMACC and Sicherheitsleitfaden

GE Profile PFSF5NFX Handbuch

Beliebte Kühlschrank Handbücher anderer Marken

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Bedienungsanleitung

Sharp

Sharp SJ-BA31IEXW2-EU Bedienungsanleitung

CORBERO

CORBERO CC2300MCW Bedienungsanleitung

KitchenAid

KitchenAid 2205264 Bedienungsanleitung

Stengel

Stengel KU 1101 A++ Bedienungsanleitung

NEFF

NEFF KI181 Series Bedienungsanleitung

Hoshizaki

Hoshizaki Reach-In Bedienungsanleitung

Amana

Amana ASD2524VES00 Bedienungsanleitung

BOMANN

BOMANN KGC 213 Bedienungsanleitung

Danby

Danby DAR044A1SLDD Montageanleitung

Samsung

Samsung RF323TE Bedienungsanleitung

Beko

Beko CSA31022 Bedienungsanleitung

IKEA

IKEA FROSTIG C 185 E Bedienungsanleitung

Electrolux

Electrolux ER 6821 D Bedienungsanleitung

True

True TS-28 Bedienungsanleitung

Frigidaire

Frigidaire FSC23R5DW9 Bedienungsanleitung

Beko

Beko LSP4579W Bedienungsanleitung