GE ZIR360NHRH Gebrauchsanweisung

SECTION 1

Product Speciﬁcation Revised 10/14

ZIR360NHRHGE Monogram®36" Built-In All-Refrigerator

SECTION 2

1/4" FRAMED PANELS 3/4" OVERLAY PANELS

FLUSH INSET INSTALLATION

STANDARD INSTALLATION

OVERALL DIMENSIONS

Dimensions in parentheses are in centimeters unless otherwise noted.

Actual product dimensions may vary due to manufacturing tolerances.

† Dimensions include 3/4" custom cabinet panel

ATTENTION ELECTRICIAN:

A 115 volt 60Hz., 15 or 20 amp power supply

is required. An inidividual properly grounded

branch circuit or circuit breaker is recommended.

Install a properly grounded 3-prong electrical

receptacle recessed into the back wall.

FLUSH INSET INSTALLATION

SPECIFICATIONS

Overall Width 38" (96.5 cm)†

Overall Height 83 1/2" (212.1 cm)†

Overall Depth 25 7/8" (65.7 cm)†

Door Clearance 38 3/4" (98.4 cm)

Cutout Width 39" (99.1 cm)

Cutout Height 84 1/2" (214.6 cm)

Cutout Depth 26 3/16" (66.5 cm)

Plumbing Requirements 1/4" OD copper

tubing or GE

SmartConnect kit

Shipping Weight 570 lb (258.5 kg)

38" (96.5)

*83 1/2"

(212.1)

*73 1/4"

(186.1)

69 13/16"

(177.3)

ZIR360NHRH

FRONT VIEW

* Shipping height. Use leveling legs and wheels for maximum 1" height

adjustment from shipping height. Nominal installation height is 84”

10 5/16"

(26.2)

20 5/8" (52.4)

25 7/8" (65.7)

*3 3/8"

(8.6) *3"

(7.6) SIDE VIEW

* 83 1/2"

(212.1)

35" (89.0)

Case width

38 3/4"

(98.4)

TOP VIEW

** Allow 4" (10.2) min

clearance to a wall

for 90˚ door swing

** These refrigerators are equipped with a 2-position door stop. The factory-set 115° door

swing can be adjusted to 90° if clearances to adjacent cabinets or walls is restricted. Allow

a 15" minimum clearance to wall for pan removal. If the 90° door stop position is used, pan

access is maintained, but pan removal is restricted.

** Allow 17" (43.2) min

clearance for 115˚

door swing

Product Speciﬁcation Revised 10/14

ZIR360NHRHGE Monogram®36" Built-In All-Refrigerator

NOTES

FLUSH INSET INSTALLATION 3/4" PANELS

Product Speciﬁcation Revised 10/14

84 1/2"

(214.6)

84 1/2"

(214.6)

FLUSH INSTALLATION

ZIF360NHLH_RH

ZIR360NHLH_RH

39" (99.1) Flush inset width

37 1/2" (95.3)

Width between cleats

(17.8)

3/4" (1.9)

Width of side cleats

5 1/4" (13.3)

1/2" (1.3)

26 3/16" (66.5)

Flush inset depth

20 15/16" (53.2)

Depth to cleat

FRONT VIEWSIDE VIEW

TOP VIEW

3 1/2"

(8.9)

Finished cleats

Case Trim

3/4" Panel

Case

Door

5 1/2"

(14.0)

26 3/16"

(66.5)

(22.9)

ELEC.

3 1/2"

(8.9)

75"

(190.5 )

From floor

to bottom

of electrical

area

WATER

3 1/2"

(9.0)

FLUSH INSET INSTALLATION 3/4" PANELS

ANTI-TIP BRACKET

24" (61.0)

1 1/2"

(3.8)

(7.6)

7/16"

(1.1)

Trim overlap

35 1/2" (90.2)

2 5/16"

(5.9)

SIDE VIEWFRONT VIEW

ZIC360NXRH

*83 1/2" min

*84 1/2" max

(212.1-214.6)

*Trim will overlap

additional 7/16"

3 1/2"

(8.9)

75"

(190.5 )

From floor

to bottom

of electrical

area

ELEC. 6"

(15.2)

10"

(25.4)

SIDE VIEW INSTALLED

WITH ANTI-TIP BRACKET

81 1/2"

(207.0)

WATER

(12.7)

3 1/2"

(9.0)

WATER

10" (25.4)

Use two

additional hole

locations at end

of brackets

Wall

Studs

Bracket

mounted

into vertical

wall studs

centered

within the

cutout

Ensure holes

selected are

centered on

the studs

FRONT VIEW OF CUTOUT

WITH ANTI-TIP BRACKET

NOTES

AMounting the junction

box in this location will

also allow for front

accessability through

access panel.

BWater supply area.

WARNING:

The refrigerator is top

heavy and must be secured

to prevent the possibility of

tipping forward. Failure to

do so may result in death

or serious injury.

The information below is

for cabinet design only.

When installing the anti-

tip system you must use

the product installation

instructions.

The information below

applies to all installation

constructions:

• A wall bracket, bolts and

toggles will be supplied

with the unit.

• The bolts will be used to

attach bracket to wall in

4 locations. Two of the

locations must penetrate

the center of the wall

studs.

• The toggles are used for

stability in drywall and

when metal studs are

encountered. Lag bolts

are used in wood studs.

• In installation opening,

measure 81 ½” from

ﬂoor and draw a

horizontal line.

• Locate and mark the wall

studs on horizontal line.

Verify at least two studs

have their centerlines

within the center 32.5”

of installation opening to

ensure 2 wall studs are

penetrated.

• The bracket will be

centered left to right in

opening with bottom of

bracket on the horizontal

line.

• When unit is placed in

opening, the bracket tabs

will align with openings

in back of the unit. The

unit will be secured to the

bracket using supplied

“L” bolts.

See Installation

Instructions for detailed

instructions.

FLUSH INSET INSTALLATION

ZIR360NHRHGE Monogram®36" Built-In All-Refrigerator

Grille Panel

Door

Panel

Door

Panel

Grille Panel

Door

Panel

NOTES

ABC

38" 9 5/8" 69 13/16"

X Y Z

1 1/4" 1" 1/2"

PANEL DIMENSIONS

A B C D

74 1/2" 9 5/8" 69 13/16" 37"

PANEL DIMENSIONS

HINGE CLEARANCE

X Y Z

1 1/4" 1" 1/2"

HINGE CLEARANCE

PANEL ASSEMBLY CROSS SECTION

FLUSH INSET 3/4" PANEL DIMENSIONS SINGLE INSTALLATION

1/4" Router Cut Depth

for Hinge Clearance

Door

3/4" Flush Inset Panel

PANEL ASSEMBLY CROSS SECTION

Finished Side of Panel

1/4" Router Cut Depth

for Hinge Clearance

Door

3/4" Flush Inset Panel

PANEL ASSEMBLY CROSS SECTION

Finished Side of Panel

Trimmed refrigerators are designed to be

customized with decorative panels. Field-

installed custom door and grille panels

are required.

Adjustment brackets allow 1/8” ne

adjustment of panel position in 3

dimensions.

Use templates provided to locate mounting

brackets on the door and grille panels.

Maximum total panel weight:

• Fresh food door panels – 67 lbs.

• Grille panel – 11 lbs

Door Handles

Door handles not included. Custom handle

supplied by your cabinet maker may be used.

ZKHPSS1: Professional tubular stainless steel

handle designed to ﬁt 3/4” panels. Kit includes

one handle – 30 1/2” long.

ZKHSS2: European tubular stainless steel

handle designed to ﬁt 3/4” panels. Kit includes

one handle – 64 1/4” long.

Order #ZUGF2H: Uniﬁed grille kit for dual

installation. Maximum total panel weight -

25 lbs.

NOTE: For side-by-side installation of a left-

and-right-hand door swing product only,

see B

on following page.

FLUSH INSET INSTALLATION

Product Speciﬁcation Revised 10/14

ROUTER 1/4" DEEP

HINGE CLEARANCES

ROUTER 1/4" DEEP

HINGE CLEARANCES

ZIR360NHRHGE Monogram®36" Built-In All-Refrigerator

FLUSH INSET 3/4" PANEL DIMENSIONS DUAL INSTALLATION

ZIF360NHLH_ZIR360NHRH

75 1/2" (191.8)

Finished Width

26 3/16" (66.5)

Min. Cutout Depth

25 3/4" (65.4)

3 7/8"

(9.8)

5 1/2"

(13.9)

(22.9)

84 1/2"

(214.6)

Finished

Opening

3 1/2"

(8.9)

FRONT VIEW

ELEC. 5 1/2"

(13.9)

(22.9)

3 1/2"

(8.9)

25" (63.5) min

To wall 25" (63.5) min

To wall

5" (12.7) min

15" (38.1) min

To wall

1 1/2"

(3.8) 4" min

(10.2)

130˚

Door swing 130˚

Door swing

75 1/2"

(191.8 )

From floor

to bottom

of electrical

area

ELEC.

SIDE VIEW

(17.8) 7"

(17.8)

WATER

3 1/2"

(9.0)

WATER

3 1/2"

(9.0)

5 3/4"

(14.6) 5 3/4"

(14.6)

NOTES

FLUSH INSET INSTALLATION

Product Speciﬁcation Revised 10/14

AA separate 115V, 60Hz, 15- or 20-amp

power supply is recommended for each

product.

BIn a side-by-side installation of a left-and-

right-hand door swing product, 1 1/2”

clearance between the units is required.

Order ZUGF2H custom panel uniﬁed grille

kit for this installation.

CIn a side-by-side installation with same

door swing, allow 4” clearance between

the products to prevent the door swing

interference. Allow 15” minimum to a wall

to achieve full interior drawer extension

and pan removal. Additional clearances

are required when using custom panels

and handles.

NOTE: ZUG2, ZUGSS2 or ZUGPP2 grille panel

kits will not ﬁt this installation.

DIn a side-by-side installation with right

and left door hinges together, allow 5”

minimum clearance between the two

products to prevent one door from striking

the other. Additional clearances required

when using custom panels and handles.

NOTE: ZUG2, ZUGSS2 or ZUGPP2 grille panel

kits will not ﬁt this installation.

DUAL PRODUCT CLEARANCES

DUAL INSTALLATIONS

ZIF360NHLH_ZIR360NHRH

75 1/2" (191.8)

Finished Width

26 3/16" (66.5)

Min. Cutout Depth

25 3/4" (65.4)

3 7/8"

(9.8)

5 1/2"

(13.9)

(22.9)

84 1/2"

(214.6)

Finished

Opening

3 1/2"

(8.9)

FRONT VIEW

ELEC. 5 1/2"

(13.9)

(22.9)

3 1/2"

(8.9)

25" (63.5) min

To wall 25" (63.5) min

To wall

5" (12.7) min

15" (38.1) min

To wall

1 1/2"

(3.8) 4" min

(10.2)

130˚

Door swing 130˚

Door swing

75 1/2"

(191.8 )

From floor

to bottom

of electrical

area

ELEC.

SIDE VIEW

(17.8) 7"

(17.8)

WATER

3 1/2"

(9.0)

WATER

3 1/2"

(9.0)

5 3/4"

(14.6) 5 3/4"

(14.6)

ZIR360NHRHGE Monogram®36" Built-In All-Refrigerator

B C

OVERALL DIMENSIONS STANDARD INSTALLATION

Product Speciﬁcation Revised 10/14

Dimensions in parentheses are in centimeters unless otherwise noted.

Actual product dimension may vary due to manufacturing tolerances.

ZIR360NHRHGE Monogram®36" Built-In All-Refrigerator

36" (91.5)

25 1/8" (63.8)

23 7/8" (60.7)

*84"

(213.4)

*73 1/4"

(186.1)

69 5/8"

(176.8)

*3"

(7.6)

1 7/8"

(4.8)

*3 1/4"

(8.3)

*83 1/2"

(212.1)

TOP VIEW

ZIR360NXRH

35"

(89.0)

Case width

36 3/4"

(93.4)

SIDE VIEWFRONT VIEW

* Shipping height. Use leveling legs and wheels for maximum

1" height adjustment from shipping height.

** Allow 4" (10.2) min

clearance to a wall

for 90˚ door swing

** Allow 25" (63.5) min

clearance for 130˚

door swing

**These units are equipped with a 2-position door stop. The factory set 130° door swing can

be adjusted to 90° if clearance to adjacent cabinets or walls is restricted. Allow 15" minimum

clearance to wall for pan removal. If the 90˚ door stop position is used, pan access is

maintained but pan removal is restricted.

ATTENTION ELECTRICIAN:

A 115 volt 60Hz., 15 or 20 amp power supply

is required. An inidividual properly grounded

branch circuit or circuit breaker is recommended.

Install a properly grounded 3-prong electrical

receptacle recessed into the back wall.

SPECIFICATIONS

Overall Width 36" (91.4 cm)

Overall Height 84" (213.4 cm)

Overall Depth 25 3/8" (64.45 cm)

Door Clearance 36 3/4" (93.4 cm)

Cutout Width 35 1/2" (90.2 cm)

Cutout Height 83 1/2" - 84 1/2"

(212.1 - 214.6 cm)

Cutout Depth 24" (61 cm)

Plumbing Requirements 1/4" OD copper

tubing or GE

SmartConnect kit

Shipping Weight 569 lb

36" (91.5)

25 1/8" (63.8)

23 7/8" (60.7)

*84"

(213.4)

*73 1/4"

(186.1)

69 5/8"

(176.8)

*3"

(7.6)

1 7/8"

(4.8)

*3 1/4"

(8.3)

*83 1/2"

(212.1)

TOP VIEW

ZIR360NXRH

35" (89.0)

Case width

36 3/4"

(93.4)

SIDE VIEWFRONT VIEW

* Shipping height. Use leveling legs and wheels for maximum

1" height adjustment from shipping height.

** Allow 4" (10.2) min

clearance to a wall

for 90˚ door swing

** Allow 25" (63.5) min

clearance for 130˚

door swing

**These units are equipped with a 2-position door stop. The factory set 130° door swing can

be adjusted to 90° if clearance to adjacent cabinets or walls is restricted. Allow 15" minimum

clearance to wall for pan removal. If the 90˚ door stop position is used, pan access is

maintained but pan removal is restricted.

NOTES

STANDARD INSTALLATION

Product Speciﬁcation Revised 10/14

AMounting the junction

box in this location will

also allow for front

accessability through

access panel.

BWater supply area.

WARNING:

The refrigerator is top

heavy and must be secured

to prevent the possibility of

tipping forward. Failure to

do so may result in death

or serious injury.

The information below is

for cabinet design only.

When installing the anti-

tip system you must use

the product installation

instructions.

The information below

applies to all installation

constructions:

• A wall bracket, bolts and

toggles will be supplied

with the unit.

• The bolts will be used to

attach bracket to wall in

4 locations. Two of the

locations must penetrate

the center of the wall

studs.

• The toggles are used for

stability in drywall and

when metal studs are

encountered. Lag bolts

are used in wood studs.

• In installation opening,

measure 81 ½” from

ﬂoor and draw a

horizontal line.

• Locate and mark the wall

studs on horizontal line.

Verify at least two studs

have their centerlines

within the center 32.5”

of installation opening to

ensure 2 wall studs are

penetrated.

• The bracket will be

centered left to right in

opening with bottom of

bracket on the horizontal

line.

• When unit is placed in

opening, the bracket tabs

will align with openings

in back of the unit. The

unit will be secured to the

bracket using supplied

“L” bolts.

See Installation

Instructions for detailed

instructions.

ANTI-TIP BRACKET

STANDARD INSTALLATION

35 1/2" (90.2)

2 5/16"

(5.9)

24" (61.0 )

1 1/2"

(3.8)

3 1/8"

(7.9)

7/16" (1.1)

Trim overlap

*83 1/2" min

*84 1/2" max

(212.1-214.6)

*Trim will overlap

additional 7/16"

3 1/2"

(8.9)

75 1/2"

(191.8 )

From floor

to bottom

of electrical

area

FRONT VIEW SIDE VIEW

3 1/2"

(8.9)

ELEC. 5 1/2"

(14.0)

(22.9)

SIDE VIEW INSTALLED

WITH ANTI-TIP BRACKET

81 1/2"

(207.0)

ZIR360NXLH

(12.7)

WATER

3 1/2"

(9.0)

Use two

additional hole

locations at end

of brackets

Wall

Studs

Bracket

mounted

into vertical

wall studs

Ensure holes

selected are

centered on

the studs

FRONT VIEW OF CUTOUT

WITH ANTI-TIP BRACKET

35 1/2" (90.2)

2 5/16"

(5.9)

24" (61.0 )

1 1/2"

(3.8)

3 1/8"

(7.9)

7/16" (1.1)

Trim overlap

*83 1/2" min

*84 1/2" max

(212.1-214.6)

*Trim will overlap

additional 7/16"

3 1/2"

(8.9)

75 1/2"

(191.8 )

From floor

to bottom

of electrical

area

FRONT VIEW SIDE VIEW

3 1/2"

(8.9)

ELEC. 5 1/2"

(14.0)

(22.9)

SIDE VIEW INSTALLED

WITH ANTI-TIP BRACKET

81 1/2"

(207.0)

ZIR360NXLH

(12.7)

WATER

3 1/2"

(9.0)

Use two

additional hole

locations at end

of brackets

Wall

Studs

Bracket

mounted

into vertical

wall studs

Ensure holes

selected are

centered on

the studs

FRONT VIEW OF CUTOUT

WITH ANTI-TIP BRACKET

ZIR360NHRHGE Monogram®36" Built-In All-Refrigerator

Product Speciﬁcation Revised 10/14

NOTES

FSide panels must be

used whenever the sides

of the refrigerator will

be exposed. The 1/4”

side panels will slip

into the side case trim.

Secure the panels to

the refrigerator with

stick-on hook and loop

fastener strips. Order

the side panels from the

cabinet manufacturer.

CUSTOM SIDE PANELS

2 9/16"

(6.5)

*3" - 4"

(7.6 - 10.2)

*Depending

on installation

height

1 7/8"

(4.8)

24" (61.0)

3/16"

(.5)

*84”

(213.4)

*Depending

on installation

*84"

(213.4)

*Depending

on installation

height

ZIF360NXLH_ZIF360NXRH _ZIFP360NXLH_ZIFP360NXRH_ ZIFS360NXLH_ZIFS360NXRH

ZIR360NXLH_ZIR360NXRH_ZIRP360NXLH_ZIRP360NXRH_ZIRS360NXLH_ZIRS360NXRH

STANDARD INSTALLATION

ZIR360NHRHGE Monogram®36" Built-In All-Refrigerator

PANEL ASSEMBLY CROSS SECTION

PANEL DIMENSIONS

.25" + .10" + .75" = 1.10" Total Panel Thickness

NOTES

STANDARD INSTALLATION

Product Speciﬁcation Revised 10/14

Trimmed refrigerators are designed to be

customized with decorative panels. Field-

installed custom door and grille panels are

required.

1/4” Framed Panels:

Order trim kit #ZTK36SDHRH

for 1/4" thick custom panels ordered from

your cabinet maker. The decorative panels

slide into the trim.

Maximum total panel weight:

• Door panel – 67 lbs.

• Grille panel – 11 lbs

3/4” Overlay Panels:

Order trim kit #ZTK36SDHRH

for 3/4" thick custom panels ordered from

your cabinet maker. The decorative panels

slide into the trim. The overlay panel must be

secured to a 1/4"-thick backer panel which

slides into the trim. A spacer panel 0.10" thick

must be placed between the overlay and

backer panels.

Center each panel over the other. Assemble

the panels with glue and screws. Screws must

be countersunk into the backer panel.

NOTE: Left-to-right offset is not always equal

to top-to-bottom offset.

Maximum total panel weight:

• Door panel – 67 lbs.

• Grille panel – 11 lbs

Door Handles:

The supplied handles can be adjusted to

accommodate both framed or overlay panels.

Custom handles of your choice, supplied by

your cabinet maker, can also be installed.

ZKHPSS1: Professional Tubular Stainless Steel

Handle designed to ﬁt 3/4" overlay panels.

Kits include one handle - 30 1/2" long.

ZKHSS2: European tubular stainless steel

handle designed to ﬁt 3/4" overlay panels.

Kits include one handle - 64 1/4" long.

ZIR360NHRHGE Monogram®36" Built-In All-Refrigerator

3/4" OVERLAY PANEL DIMENSIONS SINGLE INSTALLATION

1/4" FRAMED PANEL DIMENSIONS SINGLE INSTALLATION

ABC

1/4" Backer Panel 33 7/8" 8 7/8" 69 5/16"

.10" Spacer Panel 32 1/2" 7 5/8" 67 15/16"

3/4" Overlay Panel 34 1/8" 9" 69 9/16"

ABC

1/4" Framed Panel 33 7/8" 8 7/8" 69 5/16"

Grille Panel

Door

Panel

Grille Panel

Door

Panel

Door

1/4" Framed Panel

Supplied Handles

Trim

Door

1/4" Backer Panel

.10" Spacer Panel

Supplied Handles

Trim

3/4" Overlay Panel

NOTES

STANDARD INSTALLATION

Product Speciﬁcation Revised 10/14

Trimmed refrigerators are designed to be

customized with decorative panels. Field-

installed custom door and grille panels are

required.

1/4” Framed Panels:

Order trim kit #ZTK36SDHRH

for 1/4" thick custom panels ordered from

your cabinet maker. The decorative panels

slide into the trim.

Maximum total panel weight:

• Door panel – 67 lbs.

• Grille panel – 25 lbs

Order ZUG2: Uniﬁed grille kit for dual

installation. Maximum total panel weight -

25 lbs.

3/4” Overlay Panels:

Order trim kit #ZTK36SDHRH

for 3/4" thick custom panels ordered from

your cabinet maker. The decorative panels

slide into the trim. The overlay panel must be

secured to a 1/4"-thick backer panel which

slides into the trim. A spacer panel 0.10" thick

must be placed between the overlay and

backer panels.

Center each panel over the other. Assemble

the panels with glue and screws. Screws must

be countersunk into the backer panel.

NOTE: Left-to-right offset is not always equal

to top-to-bottom offset.

Maximum total panel weight:

• Door panel – 67 lbs.

• Grille panel – 25 lbs

Order ZUG2: Uniﬁed grille kit for dual

installation. Maximum total panel weight -

25 lbs.

Door Handles:

The supplied handles can be adjusted to

accommodate both framed or overlay panels.

Custom handles of your choice, supplied by

your cabinet maker, can also be installed.

ZKHPSS1: Professional Tubular Stainless Steel

Handle designed to ﬁt 3/4" overlay panels.

Kits include one handle - 30 1/2" long.

ZKHSS2: European tubular stainless steel

handle designed to ﬁt 3/4" overlay panels.

Kits include one handle - 64 1/4" long.

ZIR360NHRHGE Monogram®36" Built-In All-Refrigerator

STANDARD 3/4" OVERLAY PANEL DIMENSIONS DUAL INSTALLATION

STANDARD 1/4" FRAMED PANEL DIMENSIONS DUAL INSTALLATION

PANEL DIMENSIONS

1/4"

Framed

Panel

A69 7/8"

B8 7/8"

C69 5/16"

D33 7/8"

PANEL ASSEMBLY

CROSS SECTION

PANEL ASSEMBLY

CROSS SECTION

PANEL DIMENSIONS

1/4"

Backer

Panel

.10"

Spacer

Panel

3/4"

Overlay

Panel

A69 7/8" 68 1/2" 70 1/8"

B8 7/8" 7 5/8" 9"

C69 5/16" 67 15/16" 69 9/16"

D33 7/8" 32 1/2" 34 1/8"

.25" + .10" + .75" =

1.10" Total Panel Thickness

Grille Panel

Door

Panel

Door

Panel

Grille Panel

Door

Panel

Door

Panel

Door

1/4" Framed Panel Supplied Handles

Trim

Door

1/4" Backer Panel

.10" Spacer Panel

Supplied Handles

Trim

3/4" Overlay Panel

Inhaltsverzeichnis

Beliebte Kühlschrank Handbücher anderer Marken

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Bedienungsanleitung

Sharp

Sharp SJ-BA31IEXW2-EU Bedienungsanleitung

CORBERO

CORBERO CC2300MCW Bedienungsanleitung

KitchenAid

KitchenAid 2205264 Bedienungsanleitung

NEFF

NEFF KI181 Series Bedienungsanleitung

Hoshizaki

Hoshizaki Reach-In Bedienungsanleitung

Amana

Amana ASD2524VES00 Bedienungsanleitung

BOMANN

BOMANN KGC 213 Bedienungsanleitung

Danby

Danby DAR044A1SLDD Montageanleitung

Beko

Beko CSA31022 Bedienungsanleitung

IKEA

IKEA FROSTIG C 185 E Bedienungsanleitung

Electrolux

Electrolux ER 6821 D Bedienungsanleitung

True

True TS-28 Bedienungsanleitung

Frigidaire

Frigidaire FSC23R5DW9 Bedienungsanleitung

Beko

Beko LSP4579W Bedienungsanleitung

Teledyne

Teledyne 6712FR and Betriebsanleitung

Matsui

Matsui MTT50W12E Bedienungsanleitung