GE CWLSWDMBWF1 Bedienungsanleitung

Wire-Free Smart Switch

Installation Guide

Models

CWLSWDMBWF1

CWLSWCCBWF1

Simple DIY Set Up

STEP 1

Install your Wire-Free Smart Switch

STEP 2

Download the Cync App, powered

by Savant, on your smartphone

STEP 3

Add your Wire-Free Smart Switch

to the Cync App

Compatibility Requirements

Works with Cync and C by GE Smart Lights, Plugs, Switches,

and Sensors. Not compatible with non-C by GE and

non-Cync smart devices.

NOTE

Wire-Free Smart Switch and other Cync Smart Lights, Plugs,

and Switches must be grouped in the same Room/Space in the

Cync App to enable full room control.

For set up help, visit gelighting.com/cync

GE and C by GE are trademarks of General Electric Company. Used under trademark

license. Amazon, Alexa, and all related logos are trademarks of Amazon.com, Inc. or its

aﬃliates. Google and other related marks and logos are trademarks of Google LLC.

INCLUDED

YOU’LL NEED

OPTIONAL

Switch Wall Plate

Drill w/ 7/32 bit Tape Measure Level

Phillips Screwdriver

Drywall

Anchors

4 Phillips

Mounting Screws Adhesive Tape

Let's Do It

You Got This!

And we’re here to help.

For in-depth instructional videos and

a guided tour through the installation,

go to gelighting.com/cync.

Decide how you want to mount your switch.

This switch can be mounted to the wall in two ways, by

screws or adhesive tape.

Once you determine which install method is best for you,

select one of the following setup methods.

BEFORE YOU DO ANYTHING!

Location & Mounting Type

IMPORTANT Start by removing the clear plastic tab from the back of

the Smart Switch.

STEP 1

Identify where you want to mount your Wire-Free Smart Switch (switches

are typically located 48-52” from the ﬂoor to the top of the switch).

STEP 2

Prior to installation, be sure that the surface is smooth and degreased.

STEP 3

Apply adhesive tape to the middle back of the Smart Switch. Adhesive

tab should stick out from the side of the switch. This will be covered by

the wall plate and allows removal if needed in the future.

STEP 4

Mount Wire-Free Smart Switch to the wall.

STEP 5

Screw on the faceplate bracket, then snap the faceplate cover onto

the bracket.

Installing Your Smart Switch

Mounting with adhesive tape

PEEL LABEL

FOR ADHESI VE

PEEL LABEL

FOR ADHESI VE

IMPORTANT Start by removing the

clear plastic tab from the back of the

Smart Switch.

STEP 1

Identify where you want to mount your

Wire-Free Smart Switch (switches are

typically located 48-52” from the ﬂoor

to the top of the switch).

STEP 2

Mark the location for holes to be

drilled. We suggest using the mounting

holes on the switch housing as a guide.

Use the level (optional) to ensure the

switch is level before drilling holes.

STEP 3

Using 7/32” bit, drill holes in wall

for mounting screws. Insert drywall

anchors.

STEP 4

Secure the Wire-Free Smart Switch

to the wall until level and ﬂush.

STEP 5

Screw on the faceplate bracket,

then snap the faceplate cover onto

the bracket.

Installing Your Smart Switch

Mounting with screws/single-gang wall plate

IMPORTANT Start by removing the clear plastic

tab from the back of the Smart Switch.

STEP 1

Remove existing wall plate.

STEP 2

Get multi-gang wall plate (purchased separately).

STEP 3

Use new wall plate to mark the location for holes

to be drilled.

STEP 4

Using 7/32” bit, drill holes in wall for mounting

screws. Insert drywall anchors.

STEP 5

Secure the Wire-Free Smart Switch to the wall until level and ﬂush.

STEP 6

Screw on the faceplate cover onto the bracket.

Installing Your Smart Switch

Mounting with screws/2-gang wall plate

STEP 1

Download the Cync App, powered by Savant, on your

smartphone.

STEP 2

Press any button on the Smart Switch to initiate set up. LED

indicator light will ﬂash blue until app set up is complete.

STEP 3

Add your Wire-Free Smart Switch to the Cync App.

STEP 4

Group your Wire-Free Smart Switch and other C by GE or

Cync devices you want to control with the Smart Switch in

the same Room/Space in the Cync App.

Wire-Free Smart Switch + Smart Bulb

• Control lights without leaving your bed or couch

• Dim and brighten lights from the switch

• Keep switch control entering a room after moving furniture

and plugging lamps into diﬀerent sockets

Wire-Free Smart Switch + Smart Plug

• Control devices like fans and space heaters with the switch

• Add switch control to table and ﬂoor lamps with

integrated LEDs or non-standard bulbs

• Keep switch control entering a room after moving furniture

and plugging lamps into diﬀerent sockets

Wire-Free Smart Switch + Wired Smart Switch

• Create 3-way connections without rewiring

• Control lights outside a room, like a kitchen light from the

hallway

• Set up a master on/oﬀ switch next to your bed

For set up help, visit gelighting.com/cync

Simple Set Up Using the CYNC App

Unlock full features and connect to other CYNC devices

What You Can Do With

Your Wire-Free Smart Switch

STEP 1

Remove the Wire-Free Smart

Switch from the wall.

STEP 2

Remove rear housing of the switch

using Phillips screwdriver.

STEP 3

Slide the battery out, toward the

top of the switch.

STEP 4

Slide a new battery underneath

the contact strap, with the (+)

terminal toward the back of the

switch.

STEP 5

Replace rear housing.

STEP 6

Secure the Wire-Free Smart Switch

back onto the wall.

CR2032

coin battery

(actual size)

Removing/Replacing the Battery

Uses one CR2032 coin battery

Additional Information and Warnings FCC Radiation Exposure Statement

FCC Compliance Statement Compliance Notice:

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses

and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will

not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by

turning the equipment oﬀ and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit diﬀerent from that to

which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

This device complies with FCC radiation exposure limits set forth for an

uncontrolled environment. This equipment must be installed and operated

in accordance with provided instructions to provide a separation

distance of at least 20 cm from all persons.

This device complies with Part 15 of the FCC Rules. Operation is subject to

the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including

interference that may cause undesired operation.

CAUTION!

Any changes or modiﬁcations not expressly approved by the party

responsible for compliance could void the user’s authority to operate the

equipment.

Andere Handbücher für CWLSWDMBWF1

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere GE Schalten Handbücher

GE Masoneilan 496 Series Bedienungsanleitung

GE "Executive Series" USB 2.0 HO97864 Bedienungsanleitung

GE GEC-4VPHUB Montageanleitung

GE 3-Device HDMI Switch Bedienungsanleitung

GE GEH-4763 Bedienungsanleitung

GE GE-DSG-8 DSGH-5 Bedienungsanleitung

GE MultiLink ML810 Bedienungsanleitung

GE Power/Vac VM-4.16 Bedienungsanleitung

GE 45853GE Bedienungsanleitung

GE "ExecutiveSeries"USB2.0 HO97863 Bedienungsanleitung

GE Cync CSWONBLBWF1NN Bedienungsanleitung

GE MSS Bedienungsanleitung

GE EntelliGuard G Technisches Dokument

GE 70R-1000D Bedienungsanleitung

GE 50 AMP AUTOMATIC TRANSFER SWITCH Einrichtungshandbuch

GE GuardSwitch 300 Series Bedienungsanleitung

GE MultiLink Bedienungsanleitung

GE Power Break Bedienungsanleitung

GE USB 2.0 7-Port Hub HO97916 Bedienungsanleitung

GE BM-C303US5-04 Bedienungsanleitung

GE 45609 Bedienungsanleitung

GE 98209-1 Bedienungsanleitung

GE SE-100E Bedienungsanleitung

GE HO98751 Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung