GE 25880 Bedienungsanleitung
5.8GHz Speakerphone and
Answering System with Dual Cordless
Handsets and Call Waiting Caller ID
User’s Guide
25880
2
Important Information
NOTICE: This product meets the applicable Industry Canada technical specifications.
The equipment must be installed using an acceptable method of connection. The customer
should be aware that compliance with the above conditions may not prevent degradation of
service in some situations.
Repairs to certified equipment should be made by an authorized Canadian maintenance facility
designated by the supplier. Any repairs or alterations made by the user to this equipment, or
equipment malfunctions, may give the telecommunications company cause to request the user
to disconnect the equipment.
Users should ensure for their own protection that the electrical ground connections of
the power utility, telephone lines and internal metallic water pipe systems, if present, are
connected together. This precaution may be particularly important in rural areas.
CAUTION: Users should not attempt to make such connections themselves, but should
contact the appropriate electric inspection authority, or electrician, as appropriate.
NOTES: This equipment may not be used on coin service provided by the telephone company.
Interference Information
This equipment generates and uses radio frequency energy which may interfere with
residential radio and television reception if not properly installed and used in accordance
with instructions contained in this manual. Reasonable protection against such interference
is ensured, although there is no guarantee this will not occur in a given installation. If
interference is suspected and verified by switching this equipment on and off, the user is
encouraged to try to correct the interference by one or more of the following measures:
Reorient the radio/television receiver’s antenna, relocate the equipment with respect to
the receiver, plug the equipment and receiver into separate circuit outlets. The user may
also wish to consult a qualified radio/television technician for additional suggestions. This
equipment has been fully tested and complies with all limits for Class B computing devices
pursuant to part 15 FCC Rules and Regulations. This device complies with RSS-210 of Industry
Canada. Operation is subject to the following two conditions: (1) This device may not cause
interference, and (2) This device must accept any interference, including interference that may
cause undesired operation of the device.
Licensing
Licensed under US Patent 6,427,009.
Hearing Aid Compatibility (HAC)
This telephone system meets FCC/Industry Canada standards for Hearing Aid Compatibility.
REN NUMBER IS LOCATED ON THE CABINET BOTTOM
3
SEE MARKING ON BOTTOM / BACK OF PRODUCT
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING: TO
PREVENT FIRE OR
ELECTRICAL SHOCK
HAZARD, DO NOT
EXPOSE THIS
PRODUCT TO RAIN
OR MOISTURE.
THE LIGHTNING
FLASH AND ARROW
HEAD WITHIN THE
TRIANGLE IS A
WARNING SIGN
ALERTING YOU OF
“DANGEROUS
VOLTAGE” INSIDE
THE PRODUCT.
CAUTION: TO REDUCE THE
RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER (OR
BACK). NO USER
SERVICEABLE PARTS INSIDE.
REFER SERVICING TO
QUALIFIED SERVICE
PERSONNEL.
THE EXCLAMATION
POINT WITHIN THE
TRIANGLE IS A
WARNING SIGN
ALERTING YOU OF
IMPORTANT
INSTRUCTIONS
ACCOMPANYING
THE PRODUCT.
CAUTION:
Table of Contents
IMPORTANT INFORMATION ........................2
INTERFERENCE INFORMATION ....................2
LICENSING ............................................2
HEARING AID COMPATIBILITY (HAC) .........2
TABLE OF CONTENTS ..............................3
INTRODUCTION .......................................5
HANDSET AND CHARGE CRADLE LAYOUT ....7
BASE LAYOUT ........................................7
BEFORE YOU BEGIN ................................8
PARTS CHECKLIST ...............................8
TELEPHONE JACK REQUIREMENTS ..........8
IMPORTANT INSTALLATION INFORMATION .....8
IMPORTANT INSTALLATION GUIDELINES ...9
INSTALLING THE HANDSET BATTERY ...........9
INSTALLING THE PHONE .........................10
CONNECTING THE AC (ELECTRICAL)
POWER ...........................................10
CONNECTING THE TELEPHONE LINE ...... 11
CONNECTING THE CORDED HANDSET ... 11
WALL MOUNTING THE BASE .............. 11
TELEPHONE SET UP .............................12
LANGUAGE ......................................12
DISPLAY CONTRAST ..........................12
RINGS TO ANSWER ...........................13
SECURITY CODE ...............................13
RINGER LEVEL ..................................14
RINGER TONE ...................................14
SETTING DAY/TIME ...........................14
LOCAL AREA CODE ...........................15
REGISTRATION (LINK CORDLESS
HANDSET) .......................................15
DEFAULT SETTING ............................16
BASIC OPERATION ................................16
ANSWERING A CALL .........................16
CORDLESS HANDSET .....................16
CORDED HANDSET ........................17
BASE SPEAKERPHONE ....................17
MAKING A CALL ...............................17
CORDLESS HANDSET .....................17
CORDED HANDSET ........................17
SPEAKERPHONE ............................17
MANUAL CHANNEL SELECTION ...........18
CALL TIMER .....................................18
AUTO STANDBY ...............................18
RINGER VOLUME CONTROL .................18
HANDSET ....................................18
BASE UNIT ..................................18
FLASH ............................................18
CALL TRANSFER ................................19
TRANSFERRING CALL FROM BASE TO
CORDLESS HANDSET .....................19
TRANSFERRING CALL FROM CORDLESS
HANDSET TO ANOTHER CORDLESS
HANDSET/BASE ...........................19
LAST NUMBER REDIAL ......................20
BASE SPEAKERPHONE ....................20
CORDED HANDSET ........................20
CORDLESS HANDSET .....................20
4
HOLD .............................................20
PAGING THE CORDLESS HANDSET .......21
MUTE ............................................21
VOLUME .........................................21
SPEAKERPHONE ............................21
CORDED HANDSET ........................21
CORDLESS HANDSET .....................22
ANSWERING SYSTEM .....................22
SPEAKERPHONE OPERATION ................22
RECEIVING A CALL WITH
SPEAKERPHONE ............................22
MAKING A CALL WITH
SPEAKERPHONE ............................22
SWITCHING BETWEEN SPEAKERPHONE
AND HANDSET ..............................23
INTERCOM OPERATION .......................23
MAKING AN INTERCOM CALL .........23
ANSWERING AN INTERCOM CALL .....24
RECEIVING AN INCOMING TELEPHONE
CALL DURING AN INTERCOM CALL ...24
USING INTERCOM WITH A TELEPHONE
CALL ..........................................24
TWO-WAY INTERCOM CALLS .......24
CONFERENCE THE EXTERNAL
CALLER WITH CORDLESS HANDSET
AND BASE ................................25
MEMORY ............................................25
STORING A NAME AND NUMBER IN
MEMORY ........................................25
STORING A REDIAL NUMBER ..............26
INSERTING A PAUSE IN THE DIALING
SEQUENCE ......................................26
REVIEWING, CHANGING OR DELETING
STORED NAMES/NUMBERS ................27
DIALING A STORED NUMBER ..............27
CHAIN DIALING FROM MEMORY ..........28
CALLER ID (CID) ................................29
RECEIVING AND STORING CID
RECORDS ........................................29
REVIEWING CALL RECORDS ................30
TRANSFERRING CID RECORDS TO
MEMORY ........................................30
DIALING A CALLER ID NUMBER ..........31
DELETING THE CURRENT CALLER ID
RECORD ..........................................32
DELETING ALL CALLER ID RECORDS ....32
CALLER ID ERRORS ..........................33
CALL WAITING CALLER ID .................33
ANSWERING SYSTEM SET UP ................33
VOICE INSTRUCTIONS ........................33
ANSWERING SYSTEM OPERATION ...........34
RECORDING THE OUTGOING
ANNOUNCEMENT ..............................34
REVIEWING ANNOUNCEMENT ...........34
LEAVING MESSAGE ...........................34
SCREENING CALLS FROM THE BASE .....35
SCREENING CALLS FROM THE HANDSET 35
MESSAGE PLAYBACK FROM BASE UNIT 35
ERASING MESSAGES .........................36
LEAVING A MEMO ............................36
REMOTE ACCESS ..................................37
USING THE HANDSET ........................37
ANSWERING SYSTEM INDICATOR .........37
MEMORY FULL .................................37
ACCESSING THE ANSWERING SYSTEM
FROM ANOTHER LOCATION .................38
CHANGING THE SECURITY CODE ..........38
CHANGING THE BATTERY .......................39
BATTERY SAFETY PRECAUTIONS ..........39
HEADSET AND BELT CLIP OPERATION ......40
CONNECTING AN OPTIONAL HEADSET TO
THE HANDSET ..................................40
CONNECTING THE BELT CLIP ...............40
DISPLAY MESSAGES .............................40
HANDSET SOUND SIGNALS ....................42
TROUBLESHOOTING GUIDE .....................42
GENERAL PRODUCT CARE ......................44
CAUSES OF POOR RECEPTION .................45
TELEPHONE NETWORK INFORMATION .......45
INDEX ................................................46
REN NUMBER ....................................48
SERVICE .............................................48
5
Introduction
CAUTION: When using telephone equipment, there are basic safety
instructions that should always be followed. Refer to the IMPORTANT
SAFETY INSTRUCTIONS provided with this product and save them for
future reference.
Congratulations on purchasing this GE telephone/answering system. This
system operates in the 5.8GHz/900MHz frequency range, and is unique to
conventional cordless telephones. When the base is connected to electrical
power and a telephone line, it can support cordless handsets. And you can
place the fully featured cordless handsets anywhere electrical power is
available.
Features:
• 5.8GHz Technology
• Speakerphone
• Call Waiting and Caller ID Compatible
• Tone/Pulse Dialing
• Call Transfer
This telephone has been designed to be simple to use, however, you can
reach its full potential more quickly by taking a few minutes to read this
instruction book. This telephone is a multifunction product for use with Call
Waiting and Caller ID services available from your local telephone company.
Your Caller ID Call Waiting phone allows you to:
• View the name and telephone number of a caller while you are on the
phone (Call Waiting Caller ID).
• Identify callers before you answer the phone.
• View the time and date of each incoming call.
• Record up to 40 Caller ID messages sequentially in each handset and
the base.
• Know who called while you are on the other line or when you were away.
6
• Screen unwanted calls, eliminate harassment from annoying calls, or to
get prepared before answering a call.
IMPORTANT: In order to use all of the features of this telephone, you
must subscribe to two separate services available from your local telephone
company: the standard Name/Number Caller ID Service to know who is
calling when the phone rings and Caller ID with Call Waiting Service to know
who is calling while you are on the phone.
INSTALLATION NOTE: Some cordless telephones operate at frequencies
that may cause or receive interference with TVs, microwave ovens, and VCRs.
To minimize or prevent such interference, the base of the cordless telephone
should not be placed near or on top of a TV, microwave ovens, or VCR. If
such interference continues, move the cordless telephone farther away from
these appliances. Certain other communications devices may also use the
5.8GHz/900MHz frequency for communication, and, if not properly set, these
devices may interfere with each other and/or your new telephone. If you are
concerned with interference, please refer to the User’s Guide for these devices
on how to properly set channels to avoid interference. Typical devices that
may use the 5.8GHz/900MHz frequency for communication include wireless
audio/video senders, wireless computer networks, multi-handset cordless
telephone systems, and some long-range cordless telephone systems.
7
Handset and Charge Cradle Layout
Base Layout
flash/prog
(flash/program
button)
Display
caller ID/vol -/+
(caller ID/volume
-/+ button)
format/answerer
(button)
play/stop (button)
skip (button)
#pause (button)
del/chan (delete/
channel button)
erase (button)
redial (button)
talk/end/call back
(button) charge cradle with
power adaptor
charge indicator
*exit (button)
review (button)
display
memo (button)
mailbox 1/2/3 play/stop
(buttons)
caller ID skip (button)
memory/conference
(button)
redial (button)
page/intercom
(button)
speaker/call back
(button)
hold (button)
speaker volume +/-
(button)
handset volume
(button)
delete (button)
caller ID rev (button)
ans on/off
(answerer on/off
button)
format (button)
Hook switch
*exit (button)
Microphonemute (button)
#pause (button)
program/flash
(button)
announce (button)
int/transfer
(intercom/transfer
button)
memory/conference
(button)
8
Before You Begin
Parts Checklist
Make sure your package includes the items shown here.
Telephone Jack Requirements
To use this phone, you need an RJ11C type modular
telephone jack, which might look like the one pictured
here, installed in your home. If you don’t have a
modular jack, call your local phone company to find out
how to get one installed.
Important Installation Information
• Never install telephone wiring during a lightning storm.
• Never install telephone jacks in wet locations unless the jack is
specifically designed for wet locations.
• Never touch non-insulated telephone wires or terminals, unless the
telephone line has been disconnected at the network interface.
• Use caution when installing or modifying telephone lines.
• Temporarily disconnect any equipment connected to the phone such as
faxes, other phones, or modems.
Modular
telephone
line jack
Wall plate
Base
2 cordless
handsets
Belt clips
Desktop/Wall
Mounting pedestal
AC power
adaptor
Telephone
line cord
Handset
batteries
Coiled handset
cord
Base Handset
2 cordless handset
charger cradles
Battery
compartment
doors
9
Important Installation Guidelines
• Install telephone near both a telephone (modular) jack and an electrical
power outlet.
• Avoid sources of noise, such as a window by a busy street, and electrical
noise, such as motors, microwave ovens, and fluorescent lighting.
• Avoid heat sources, such as heating air ducts, heating appliances,
radiators, and direct sunlight.
• Avoid areas of excessive moisture or extremely low temperature.
• Avoid dusty locations.
• Avoid other cordless telephones or personal computers.
Installing the Handset Battery
NOTE: You must connect the handset battery before using the cordless handsets.
CAUTION: To reduce the risk of fire or personal injury, only use the
ATLINKS Ni-CAD battery model 5-2548 that is compatible with this unit.
1. Locate battery and battery door which are packaged together inside a
plastic bag and are separate from the handset.
2. Locate the battery compartment on the back of the handset.
3. Plug the battery pack cord into the jack inside the compartment.
NOTE: It is important to maintain the polarity (black and red wires) to
the jack inside the compartment. To ensure proper battery installation, the
connector is keyed and can be inserted only one way.
RED WIRE
BLACK WIRE
BATTERY
PRESS DOWN
FIRMLY
4. Insert the battery pack.
5. Close the battery compartment by pushing the door up until it snaps
into place.
10
6. Place the handsets in the charging cradles.
Allow handsets to charge for 16 hours prior to first use. If you don’t properly
charge the handsets, battery performance is compromised.
NOTE: If the battery is not properly installed in the handset, or if the battery
pack is not properly connected to the jack inside the battery compartment.
NO BATTERY shows in the display when the handset is placed in the charging
cradle.
Installing the Phone
Choose the best location to install your base and handset charge cradles.
Your base and handset charge cradles should be placed on a level surface
such as a desk or table top, or you may mount the base on a wall.
Connecting the AC (Electrical) Power
1. On the base, plug the power adaptor cord into the power jack on the back
of the base and the other into an electrical outlet. If desired, store the
extra power adaptor line cord inside desktop pedestal.
CAUTION: Use only the ATLINKS USA, Inc. 5-2598 (black) and 5-2625
(gray color adapter for white unit) power adaptor that came with this
unit. Using other power adaptors may damage the unit.
2. Plug the handset charge cradle into an electrical outlet.
NOTE: The charge indicator on the handset charge cradle turns on to
indicate the handset battery is charging.
Andere Handbücher für 25880
1
Inhaltsverzeichnis
Sprachen:
Andere GE Telefon Handbücher
GE
GE 2-9190 Bedienungsanleitung
GE
GE SPACEMAKER 26976 Bedienungsanleitung
GE
GE 28871 Bedienungsanleitung
GE
GE Feb-50 Bedienungsanleitung
GE
GE ES29195 Bedienungsanleitung
GE
GE 29267GE3 Bedienungsanleitung
GE
GE 29585FE1 Bedienungsanleitung
GE
GE 29480 Bedienungsanleitung
GE
GE 27881 Bedienungsanleitung
GE
GE AU29490GE1 Bedienungsanleitung
GE
GE DECT 0008579 Bedienungsanleitung
GE
GE 2-9233 Bedienungsanleitung
GE
GE DECT6.0 28127 Bedienungsanleitung
GE
GE 25982 Bedienungsanleitung
GE
GE 29115AE1 Bedienungsanleitung
GE
GE 29460 Bedienungsanleitung
GE
GE 29568 Bedienungsanleitung
GE
GE 2-9710 Bedienungsanleitung
GE
GE 29418 Bedienungsanleitung
GE
GE TRIMLINE PHONE 29253 Bedienungsanleitung
