GE 15163 Bedienungsanleitung

Quick Start Guide

Commonly used tools

- Phillips head screwdriver

- Flat head screwdriver

- Hammer

- Wire cutter/stripper

Supplied hardware

- #10 Screw (3)

- #10 Drywall anchors

MIN. COPPER WIRE

SIZE (AWG)

MAX LOAD

(AMP)

MINIMUM INSULATION

TEMP (°C)

PRESSURE PLATE

TERMINAL SCREW

MAKE SURE WIRE

INSULATION CLEARS

PRESSURE PLATE

14 15 60

12 20 60

10 30 60

8 40 105

USE CORRECT GAUGE WIRE PER LOCAL ELECTRICAL CODE

• RECOMMENDED INSTALLATION BY LICENSED ELECTRICIAN.

• HIGH VOLTAGE (THERE MAY BE MORE THAT ONE SOURCE OF SUPPLY)

DISCONNECT ALL POWER SOURCES BEFORE SERVICING.

• RISK OF ELECTRIC SHOCK – ALL TERMINALS ARE LIVE.

• USE COPPER WIRE ONLY.

• CLOSE THE COVER AFTER SETTING.

• TIGHTEN CONNECTIONS TO 25 LBF-IN.

• USE CORRECT GAUGE WIRE (8-14 AWG) BASED ON LOCAL ELECTRICAL

CODE OF AT LEAST 105C RATING.

• APPROVED FOR OUTDOOR USE.

• WIRE STRIP LENGTH ½”

• GROUNDING: NATIONAL ELECTRICAL CODE REQUIRES THAT GROUNDING

MUST BE CONTINUOUS AND IN PROPER ELECTRICAL CONTACT IN ALL

GROUNDING CONDUCTORS, METALLIC CONDUITS AND GROUNDING

TERMINALS.

WARNING

Knockouts

Each metal box comes with ½” and ¾” knockouts. Follow the pictures below to

remove knockouts.

For ½” knockout, place small blade screw driver as pictured above. Tap lightly to

punch knockout loose.

For ¾” knockout, ﬁrst use screwdriver to punchout ½” knockout then use pliers

to remove outer ring.

Final result of ¾” knockout

Mounting the timer

1. Select the location for the timer and use the three holes provided for

mounting.

Mounting holes

2. Remove module from timer box. Hold the timer box in place and mark the

holes on the mounting surface.

3. If mounting to drywall:

a.) Drill a 3/16” size hole for the drywall anchors at the marked locations

b.) Insert an anchor in each hole then gently tap the open end of anchor with

a hammer until the anchor is almost ﬂush with the wall.

c.) Mount the timer to the anchors using the supplied screws.

4. If mounting to plywood, drill a 3/32” size hole for each screw and mount the

timer to the surface using the supplied screws.

120 VAC Setup: Single 120 VAC Load

Connections:

L- Line Input to Timer Motor

1-Line Input to Switch

X-Neutral Input to Timer Motor

2-Line Output of Switch

2XL

LOAD

Removable

Bridge

Typical for same voltage in LOAD and MOTOR

GROUND

L X1 2

• RECOMMENDED INSTALLATION BY LICENSED ELECTRICIAN.

• HIGH VOLTAGE (THERE MAY BE MORE THAT ONE SOURCE OF SUPPLY)

DISCONNECT ALL POWER SOURCES BEFORE SERVICING.

• RISK OF ELECTRIC SHOCK – ALL TERMINALS ARE LIVE.

• USE COPPER WIRE ONLY.

• CLOSE THE COVER AFTER SETTING.

• TIGHTEN CONNECTIONS TO 25 LBF-IN.

• USE CORRECT GAUGE WIRE (8-14 AWG) BASED ON LOCAL ELECTRICAL

CODE OF AT LEAST 105C RATING.

• APPROVED FOR OUTDOOR USE.

• WIRE STRIP LENGTH ½”

• GROUNDING: NATIONAL ELECTRICAL CODE REQUIRES THAT GROUNDING

MUST BE CONTINUOUS AND IN PROPER ELECTRICAL CONTACT IN ALL

GROUNDING CONDUCTORS, METALLIC CONDUITS AND GROUNDING

TERMINALS.

WARNING

Step 1: Remove Plastic Guard

Remove screws using a Phillips Head

screwdriver and keep them to the side.

Carefully remove plastic guard and

also keep to the side.

Step 2: Connect the Input/Clock Motor Voltage

1. Connect 120VAC Hot

(Black) to Terminal L.

Do not remove the

jumper connecting

Terminals “L” and “1”.

2. Connect 120VAC

Neutral (White) to

terminal X.

3. Connect the bare wire

to the ground lug.

Tighten the screw

terminals to 25lbf-in.

Improper tightening can cause heating and equipment failure.

Step 3: Complete the circuit to the load

1. Connect 120VAC Hot

(Black) of the LOAD to

Terminal 2.

2. Connect 120VAC

Neutral of the Load

(White) to terminal X.

3. Connect the bare wire

to the ground lug.

Tighten the screw

terminals to 25in-lb.

Improper tightening

can cause heating and

equipment failure.

Step 4: Reinstall the Plastic Guard

Install both screws with the plastic

guard facing the original position.

Removable Bridge

Step 5: Activate Timer

1. Turn the mechanism dial counter

clockwise to set the current time as

accurately as possible.

2. After wiring and setting the timer

with the ON/OFF trippers in the

correct timer positions. Be sure to

depress the ON or OFF lever to set

the timer to the desired state. The

timer will turn ON or OFF at the next

programmed time.

3. You cannot see the dial turning.

Wait at least 30 minutes after the

set ON or OFF time to verify the

timer is operating properly.

Step 6: Check timer after 24 hours

1. After 24 hours, remove power from the timer and check the connections:

a.) Remove plastic guard

b.) Verify all screws and connections are still ﬁrmly tightened.

c.) It is possible that after your initial tightening, the wire has compressed and

loosened the connections.

2. After making sure everything is still tight, replace the plastic guard and

restore power to the timer.

*Please review “Operating Instructions” in the user manual.

Special note for plastic guard

on the back of the motor

On the back of the motor, there is a

plastic guard for “Input” side

connections. It snaps easily in and out

of place. If the guard has come off

during shipment or installation,

reinstall by placing the two tabs at the

bottom in the appropriate slots.

Plastic guard ﬁtted correctly

Pictured is plastic guard

Ends ﬁt into these holes

15163 VERSION 2

01/13/16

WWW.JASCOPRODUCTS.COM

Inhaltsverzeichnis

Andere GE Timer Handbücher

GE 15266 Bedienungsanleitung

GE 15057 Bedienungsanleitung

GE SunSmart 15089 Bedienungsanleitung

GE GE 15136 Bedienungsanleitung

GE SunSmart 15312 Installationshandbuch

GE 15270 Bedienungsanleitung

GE SunSmart 15042 Bedienungsanleitung

GE 15087 Bedienungsanleitung

GE 15147 Bedienungsanleitung

GE SunSmart 15079 Bedienungsanleitung

GE Indoor SunSmart Bedienungsanleitung

GE 56922 Bedienungsanleitung

GE Indoor SunSmart Bedienungsanleitung

GE SunSmart 15042 Bedienungsanleitung

GE HEAVY DUTY OUTDOOR DIGITAL STAKE TIMER Bedienungsanleitung

GE Indoor SunSmart Bedienungsanleitung

GE Digital Timer Bedienungsanleitung

GE SunSmart 15312 Bedienungsanleitung

GE 15430 Bedienungsanleitung

GE 15143 Bedienungsanleitung

GE 15136 Bedienungsanleitung

GE SunSmart Digital Timer Bedienungsanleitung

Beliebte Timer Handbücher anderer Marken

Intermatic

Intermatic P1131 Bedienungsanleitung

Learning Resources

Learning Resources Time Tracker mini Bedienungsanleitung

CEBEK

CEBEK I-215 Bedienungsanleitung

Somogyi

Somogyi home TS MD 5 Bedienungsanleitung

Profile

Profile 010200280 Bedienungsanleitung

Gizmo

Gizmo T4 Bedienungsanleitung

Tekmar

Tekmar Timer 031 Bedienungsanleitung

Daikin

Daikin DST301B61 Bedienungsanleitung

sisel

sisel ENDA ETM2432 Bedienungsanleitung

B&Q

B&Q TE103 Bedienungs- und Wartungshandbuch

Hozelock

Hozelock AC Plus 2700 Bedienungsanleitung

GIC

GIC Eliro V7DDSS3Eliro V7DFTS3 Bedienungsanleitung

Tork

Tork TU40 Bedienungsanleitung

Emos

Emos EMT400F Bedienungsanleitung

FarmTek

FarmTek Polaris Bedienungsanleitung

Maximum

Maximum CRONUS Bedienungsanleitung

Uberhaus

Uberhaus TD133B Bedienungsanleitung

Clas Ohlson

Clas Ohlson 31-3766 Bedienungsanleitung