GE 23151 Bedienungsanleitung

Full-Motion

Flat Screen TV Mount

User Manual

Model 23151

8/12 vers1

Questions? Call 1-800-654-8483

M-F, 8-5pm CST

or visit www.jascoproducts.com

Easy to install,

mounts in minutes

UP TO

42"

55 lbs. Max

Thank you for purchasing this GE product! The GE Flat Panel Wall Mount

allows you to easily, quickly and securely mount your ﬂat screen display to a

wall. Please review these instructions carefully before beginning installation.

Please verify the mounting hole locations (VESA compatibility) of your display

to ensure proper installation. For further detailed instructions, please visit our

web site at www.jascoproducts.com.

SPECIFICATIONS

• Display Size: 13–42”

• Maximum Load: 55 lbs (25 kg)

• VESA Mounting Pattern:

200 mm x 200 mm Max

• Tilt Range: +/- 13.8°

• Pan/Swivel Range: up to 180°

• Horizontal Rotation: 360°

• Proﬁle: 3.1” to 10.8” (7.9 cm to 27.4 cm)

TOOLS REQUIRED

• Philips Screw Driver

• Pliers

• Drill & Drill Bit (1/8” (3mm) drywall;

5/16” (8mm) concrete)

• Wall Stud Locator (drywall installation)

*Tools not included

WARNINGS

1. Read these instructions carefully before

you begin. If you are unsure of any part

of the process, contact a professional

contractor or installer for assistance.

Improper installation can result in injury or

damage.

2. Use with products heavier than 25kg

(55lbs.) may result in instability and

possible injury.

3. The wall or mounting surface must be

capable of supporting the combined weight

of the mount and the display; if not, the

structure must be reinforced.

4. Safety gear and proper tools must be used.

Failure to do so can result in injury and/or

damage.

5. A minimum of two people are required for

installation. Do not attempt to install this

mount alone under any circumstances.

6. Follow all instructions and

recommendations regarding adequate

ventilation and suitable locations for

mounting your display. Consult the owner’s

manual for your particular display for more

information.

7. Seller/manufacturer is not liable for

damages or injury caused by incorrect

mounting, assembly or use.

8. This product contains small items that

could be a choking hazard if swallowed.

Keep these items away from children.

**This wall mount is for indoor

installation only**

HARDWARE KIT

A - Drywall screw (x3)

B - Concrete anchor (x3)

C - M4 x 12 screw (x4)

D - M4 Locknut (x4)

E - M4 x 12 screw (x4)

F - M4 x 20 screw (x4)

G - M6 x 12 screw (x4)

H - M6 x 20 screw (x4)

I - M6 washer (x4)

J - Spacer (x4)

K - S4 Allen key (x1)

DRYWALL INSTALLATION

INSTRUCTIONS

**IMPORTANT** For safety reasons, this

mount must be secured to a wood stud

capable of supporting the combined weight

of the mount and display. **DO NOT MOUNT

TO DRYWALL ALONE**

1. Use a high quality stud ﬁnder to locate the

stud where you wish to install your mount.

Mark both edges of the stud to help identify

the exact center.

**NOTE**: You must use the center of each

stud to avoid cracking or splitting the wood

during installation.

2. Place the wall plate against the wall and

level it using the integrated bubble level.

3. While another person holds the wall plate in

position, mark three locations for securing

the mount to the wall (See Fig. 1).

4. Drill a 1/8” (3mm) pilot hole at each

marked location.

5. Place the wall plate back against the wall

and attach it using the drywall screws (A)

provided in the hardware kit (see Fig. 2)

FIG. 1

FIG. 2

CONCRETE INSTALLATION

INSTRUCTIONS

**IMPORTANT** For safety reasons, the

concrete wall must be capable of supporting

the combined weight of the mount and the

display. The seller/manufacturer takes no

responsibility for the failure caused by walls

or insufﬁcient strength.

**IMPORTANT** If installing the mount into

a concrete block or brick surface, never drill

into the mortar between blocks or bricks.

YOU MUST SECURE THE MOUNT TO THE

CONCRETE BLOCK OR BRICK.

1. Place the wall plate against the wall in

the desired location and level it using the

integrated bubble level.

2. While another person holds the wall plate in

place, mark three evenly spaced locations

on the wall for securing the mount

(see Fig. 3).

Do not over-

tighten these

screws.

Ensure that

the wall plate

remains level

after all screws

are secured.

FIG. 3

3. Drill an 5/16”

(8mm) hole at

each marked

location.

Remove any

excess dust

from the holes.

4. Insert a concrete

anchor (B) into each

hole so that it is

ﬂush with the concrete

surface (see ﬁg. 4).

A hammer can be

used to lightly

tap the anchors

into place if

necessary.

FIG. 4

**Note** If the concrete wall is covered by

a layer of plaster or drywall, the concrete

anchor mush pass completely through the

layer to sit ﬂush with the concrete surface.

5. Place the wall plate back

against the wall and

attach it using the

drywall screws (A)

provided in the hardware

kit (See Fig. 2). Do not

over-tighten these bolts

and do not release the

wall plate until all bolts

are in place. Ensure that the wall plate

remains level after all bolts are secured.

ATTACHING THE MOUNT TO

THE DISPLAY

**IMPORTANT** Use extra care during this

part of the installation. If possible, avoid

placing your display facedown as it may

damage the viewing surface.

**NOTE** This mount comes with a selection

of different screw diameters and lengths

to accommodate a wide variety of display/

monitor/television models. Not all of the

hardware in the kit will be used. If you

cannot ﬁnd the appropriate screw size in the

kit provided, consult the manufacturer of

your display for more information.

1. Examine the mounting holes on the back of

your display:

A. If the mounting holes are spaced 75mm x

75mm or 100mm x 100mm apart, skip

this section and proceed with Step 2.

B. If the mounting holes are spaced 100mm

x 200mm or 200mm x 200mm apart, you

will need to use the adaptor plates

included with your mount. Attach these to

the mount according to the illustration

(see Fig. 5). Use the M4 x 12 screws (C), and

M4 Locking Nuts (D) from the hardware kit.

FIG. 2

**Note** You must attach the adaptor

plates using the four countersunk holes

located on the adaptor plates.

2. Determine the correct length of screw to

use by examining the back of your display.

A. If the back of your display is ﬂat and the

mounting holes are ﬂush with the

surface, you will use the shorter screws

from the hardware kit.

B. If the back of your display is curved,

has a protrusion, or if the mounting

holes are recessed, you will need to use

the longer screws and the spacers

provided in the hardware kit.

3. Determine the correct diameter of screw to

use by carefully trying one of each size (M4

and M6) from the hardware kit.

**Note** Do not force any of the screws – if

you feel resistance stop immediately and try

a smaller diameter screw.

4. Attach the mount to the back of your

display using the screws identiﬁed in Steps

2 and 3. If you are using the longer screws

on a display with a curved or recessed

back, you may also need to use the spacers

(J) provided in the hardware kit. Only use a

spacer if necessary.

Countersunk

Holes

FIG. 5

FINAL ASSEMBLY

1. To complete the installation, carefully slide

the mount with your display attached into

the wall plate (See Fig. 6). Do not release

the display until the mount is securely

placed in the wall plate. If you need to

remove the mount from the wall, carefully

slide the mount upwards and out of the

wall plate.

2. Tighten the set screw located on the upper

front portion of the wall plate using the S4

Allen Key (K) provided in the hardware kit

(See Fig. 7). Remember to remove the set

screw before attempting to remove the

mount from the wall plate.

**IMPORTANT**

The set screw should

be used at all times to

prevent the mount from

being accidentally lifted

from the wall.

3. Cables can be routed

through the hook

located at the bottom

of the wall plate to keep

them organized and

out of the way.

FIG. 6

FIG. 7

OPERATION AND

ADJUSTMENT

1. To adjust the tilt angle or rotate your

screen, ﬁrmly grasp the sides of you display

and carefully move it into position. If you

ﬁnd the mount is too difﬁcult to move or is

too loose to hold your display in position,

adjust the three screws located directly

behind the head of the mount using the S4

Allen Key provided in the hardware kit (See

Fig. 8). Adjust all three screws evenly.

2. Swivel adjustments can be made simply by

moving your display to the desired position.

If any of the swivel joints are too tight or

too loose, they can be adjusted using the

S4 Allen Key provided in the hardware kit

(See Fig. 9).

3. Periodically clean your mount with a dry

cloth. Inspect all screws and hardware

at regular intervals to ensure that no

connections have become loose over time.

Re-tighten as needed.

FIG. 8

FIG. 9

TECHNICAL SUPPORT:

For additional assistance:

Online: www.jascoproducts.com/support

Email: [email protected]

Our in-house call center is open M-F, 8-5pm

central (except holidays and special events).

For product information, troubleshooting and

warranty calls:

800-654-8483, option 1

For consumer/business sales:

800-654-8483, option 2

Mailing Address:

Jasco Products Company, Attn: CIC,

10 E Memorial Rd, Bldg B,

Oklahoma City, OK 73114

Please contact technical support (using one

of the above options) before attempting to

ship product returns or warranty requests.

Failure to do so may delay processing times

considerably.

ONE-YEAR LIMITED

WARRANTY

Jasco Products Company warrants this

product to be free from manufacturing

defects for a period of one year from

the original date of consumer purchase.

This warranty is limited to the repair or

replacement of this product only and does

not extend to consequential or incidental

damage to other products that may be

used with this unit. This warranty is in lieu

of all other warranties express or implied.

Some states do not allow limitations on how

long an implied warranty lasts or permit

the exclusion or limitation of incidental

or consequential damages, so the above

limitations may not apply to you. This

warranty gives you speciﬁc rights, and you

may also have other rights which vary from

state to state. If unit appears to be defective

within the warranty period, please contact

out technical support team for assistance

(‘Technical Support’ section in the manual).

is a trademark of General Electric Company

and is under license by Jasco Products Company LLC,

10 E. Memorial Road, Oklahoma City, OK 73114

www.jascoproducts.com

Inhaltsverzeichnis

Andere GE TV-Halterung Handbücher

GE WR30X10093 Bedienungsanleitung

Beliebte TV-Halterung Handbücher anderer Marken

Ergotron

Ergotron Neo Flex Cantilever UHD Bedienungsanleitung

StarTech.com

StarTech.com FPCEILBTB Bedienungsanleitung

VonHaus

VonHaus 05/038 Bedienungsanleitung

Techlink

Techlink ECHO TV Bedienungsanleitung

Sandstrom

Sandstrom SSTVMC12X Bedienungsanleitung

Sony

Sony SU-WL700 Leitfaden

ICW

ICW SCACC18 Bedienungsanleitung

LG WM-L640V Bedienungsanleitung

Gembird

Gembird WM-65ST-01 Bedienungsanleitung

ERARD

ERARD FiTUP XXL 035320 Bedienungsanleitung

PEERLESS

PEERLESS PLCK-1 Leitfaden

Kanto

Kanto RCF180 Bedienungsanleitung

GEM

GEM GEM GP001 Bedienungsanleitung

Gladiator Joe

Gladiator Joe GJ0A0053 Bedienungsanleitung

Vivotek

Vivotek AM-105 Bedienungsanleitung

Vivo

Vivo VESA STAND-VAD1B Bedienungsanleitung

AmazonBasics

AmazonBasics B07QG3LMG4 Bedienungsanleitung

Secura

Secura QLF210 Bedienungsanleitung