GE 700 VA Bedienungsanleitung

Digital Energy

Firmware Update

Installation Guide

Digital Energy™ Uninterruptible Power Supply

On-line VH Series UPS

700 - 1000 - 1500 - 2000 - 3000 VA

GE Consumer & Industrial SA

General Electric Company

CH – 6595 Riazzino (Locarno)

Switzerland

T +41 (0)91 / 850 51 51

F +41 (0)91 / 850 51 44

www.gedigitalenergy.com

Contents

1Safety rules ..................................................................................................................... 3

2Introduction .................................................................................................................... 3

3Switching off and unplug the battery................................................................. 4

4Remove top cover of the UPS................................................................................. 5

5Remove dangerous voltage .................................................................................... 6

6Unplug the control board......................................................................................... 8

7Programmer plug-in................................................................................................... 9

8Firmware update .......................................................................................................11

9Closing and testing....................................................................................................13

Modifications reserved 2 ISG_VHS_FRM_UPD_XGB_V010.doc

1Safety rules

This manual contains all necessary information about the correct use of the VH Programming Board for a

firmware update of the Digital Energy™ VH Series. Before attempting to install or operate the equipment,

carefully read this manual. Keep this manual together with the User manual next to the UPS for future

references.

Full understanding of and compliance with the safety instructions and warnings contained in this

manual are the

ONLY CONDITIONS

to avoid any dangerous situation during installation, operation and maintenance work, and to preserve the

maximum reliability of the UPS system.

NOTE

The “Firmware Update” must be performed by a QUALIFIED SERVICE PERSON*.

Please refer to the “Safety Rules” included in the “User Manual” of the UPS.

If any problems are encountered with the description of this installation guide, please

contact the nearest Service Centre before proceeding.

CAUTION!

These are sensitive electronic devices. Risk of electrostatic discharge!

Qualified, skilled personnel

are persons who (because of their training, experience, and position as well as their knowledge of appropriate

standards, regulations, health and safety requirements and working conditions) are authorized to be

responsible for the safety of the equipment, at all times whilst carrying out their normal duties and are

therefore aware of, and can report, possible hazards (observe IEC 60364 and national wiring regulations and

accident prevention rules).

GE refuses any responsibility in case of non-observance, unauthorized alterations or improper use of the

delivered UPS.

While every care has been taken to ensure the completeness and accuracy of this manual, GE accepts no

responsibility or liability for any loss or damage resulting from the use of the information contained in this

document.

This document shall not be copied nor reproduced without the permission of GE.

Due to technical improvements, some of the information contained in this manual may be changed without

notice.

2Introduction

Description

The Firmware Update must be performed using the Programming Board that is an option required when the

Digital Energy™ UPS VH Series model should be updated. The correct use of the Programming Board must

be performed with the using of an E8a Programmer and an External Power Supply adjusted between 4.75

and 5.8 Volt.

Do not attempt the Digital Energy™ UPS VH Series if all the necessary equipment is not available.

Modifications reserved 3 ISG_VHS_FRM_UPD_XGB_V010.doc

3Switching off and unplug the battery

•1Press keypad ‘O’ for 1 second to switch off the UPS then disconnect the mains cable.

•2Pull out the lower part of the front panel to remove it.

•3Disconnect the DC connector of the internal batteries, then press the keypad ‘I ’ to discharge the capacitors.

Modifications reserved 4 ISG_VHS_FRM_UPD_XGB_V010.doc

4Remove top cover of the UPS

•1Place the UPS horizontally on a table or desk.

•2Remove the 3 screws how indicated on the picture.

•3Slide out the cover in the indicated direction and Pull up the cover to remove it from the UPS.

Modifications reserved 5 ISG_VHS_FRM_UPD_XGB_V010.doc

5Remove dangerous voltage

CAUTION

To avoid damage due to ESD (ElectroStatic Discharge) be sure that maintenance work is

performed under ESD-safe conditions: work on an anti-static mat; ground yourself and the unit

when it is opened.

CAUTION

When the UPS is uncovered use the proper caution to not damage the board and all the

electrical parts.

•1Wait 10 Minutes to allow discharge of the DC-Capacitors.

Put a multimeter on the 2 indicated points to check if the capacitor is discharged.

(remaining voltage has to be less than <20V)

Use a 100 Ohm / 10 Watt resistor to discharge the capacitor on the correct indicated points how

shown in the picture.

Modifications reserved 6 ISG_VHS_FRM_UPD_XGB_V010.doc

•2Procedure:

•Shut the UPS down by pressing key ‘0’ on the Operating panel.

•Remove Mains voltage from the input socket.

•Remove the Front Panel and disconnect the Battery plug.

•Wait 10 Minutes to allow discharge of the DC-Capacitors.

•Remove dangerous voltage and then remove the UPS cover, following instructions on page 5.

•Measure the voltage across R316/R345* and R317/R346*. ( < 20 Volt )

*(For VH700-VH1500 measure voltage on resistor R345/R346, and for VH2000/VH3000 on R316/R317)

Modifications reserved 7 ISG_VHS_FRM_UPD_XGB_V010.doc

6Unplug the control board

•1Remove the 3 cables and the small board how indicated on the picture.

•2Remove the 2 screws that keep the lock tab for the control board.

•3Slide up the control board out of the VH cabinet.

Modifications reserved 8 ISG_VHS_FRM_UPD_XGB_V010.doc

7Programmer plug-in

Top view of the VH Prog. Board Top view of the E8a Programmer

Top view of the IM0128A5 Board

•1Insert the J1 connector of the VH Prog. Board in mid-position of J4 connector of the IM0128A5.

NOTE: Pay attention that J1 pins are correctly fixed on J4 connector.

Fig. 1

Modifications reserved 9 ISG_VHS_FRM_UPD_XGB_V010.doc

•2Insert the flat cable on J2 connector of the VH Prog. Board.

Fig. 2

•3Connect USB and the flat cable to the E8a Programmer.

Fig. 3

•4Top view of the final cabling for the firmware update with the VH Programming Board for

Digital Energy™ VH Series.

NOTE: Pins 13 and 14 are 5V plug-in, and pins 15 and 16 are GND plug-in.

Fig. 4

Modifications reserved 10 ISG_VHS_FRM_UPD_XGB_V010.doc

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere GE UPS Handbücher

GE GT6000 Bedienungsanleitung

GE Digital Energy LP 33 Series Bedienungsanleitung

GE Lanpro 33 Bedienungsanleitung

GE GT Series Bedienungsanleitung

GE SG 750 UL S2 Series Bedienungsanleitung

GE 750 UL S2 Bedienungsanleitung

GE Uninterruptible Power Supply Bedienungsanleitung

GE Digital Energy LP 33 Series Bedienungsanleitung

GE Digital Energy Bedienungsanleitung

GE Digital Energy SitePro 400 VAC CESeries 7 Bedienungsanleitung

GE Digital Energy SG Series Bedienungsanleitung

GE Amersham Imager 600 Bedienungsanleitung

GE EP 700T Bedienungsanleitung

GE Digital Energy LP 11 Bedienungsanleitung

GE SG 300 Bedienungsanleitung

GE 600 - 1500 VA Bedienungsanleitung

GE LP 33U Series Bedienungsanleitung

GE LanPro 11 U Bedienungsanleitung

GE SG 225 Bedienungsanleitung

GE Digital Energy SG 400 kVA Bedienungsanleitung

GE TLE 160 Bedienungsanleitung

GE Digital Energy LP 11U Bedienungsanleitung

GE 1000-1500-2000-3000 VA Bedienungsanleitung

GE On-line VH Series Bedienungsanleitung

Beliebte UPS Handbücher anderer Marken

Pylontech

Pylontech Victron & Pylontech US5000 Bedienungsanleitung

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Bedienungsanleitung

Mecer

Mecer ME-1000-WTU Bedienungsanleitung

Mustek

Mustek PowerMust 530(B) Plus Installations- und Betriebshandbuch

Emerson

Emerson Liebert NXL series Bedienungsanleitung

MAKELSAN

MAKELSAN BOXER SERIES Bedienungsanleitung

Block

Block PC-0524-400-0 Bedienungsanleitung

CyberPower

CyberPower CP585LCD Bedienungsanleitung

Eaton

Eaton 3S Montageanleitung

CyberPower

CyberPower Office Tower Series UPS 1000 Bedienungsanleitung

CyberPower

CyberPower BM100 Bedienungsanleitung

Best Power

Best Power 610 Bedienungsanleitung

Best Power

Best Power Unity/I UT3K Bedienungsanleitung

Mustek

Mustek PowerMust 400 Offline Bedienungsanleitung

Xantrex

Xantrex Trace 512 UR-UPS Bedienungsanleitung

Forza

Forza SL-1501UL Bedienungsanleitung

LEGRAND

LEGRAND keor 310081 Bedienungsanleitung

ABB

ABB Conceptpower DPA 500 Bedienungsanleitung