GE Appliances G153 Bedienungsanleitung

GEAppliances.com

Safety Instructions .......... 2,3

Operating Instructions

Care and Cleaning

of the Washer ...................... 7

Control Panel ...................... 4

Control Settings ................. 4-5

Features ........................... 6

Loading and Using

the Washer ........................ 7

Troubleshooting Tips....... 8-1o

Consumer Support

Consumer Support ................ 12

Warranty .......................... 11

Write the model and serial

number here:

Model #

Serial #

You can find them

under the lid of

the washer,

49-90434 02-12 GE

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

AWARNING! of fire or explosion, electric" shock, or to prevent property damage, personal injury,

or loss of life.

WATERHEATERSAFETY

Under certain conditions, hydrogen gas may be produced in awater heater that has not been used

for two weeks or more. Hydrogen gas can be explosive under these circumstances.

If the hot water has not been used for two weeks or more, prevent the possibility of damage or injury by turning

on all hot water faucets and allowing them to run for several minutes. Do this before using any electrical appliance

which is connected to the hot water system. This simple procedure will allow any

built-up hydrogen gas to escape. Since the gas is flammable, do not smoke or use an open flame or

appliance during this process.

PROPERINSTALLATION

This washer must be properly installed and located in accordance with the installation instructions

before it is used. If you did not receive an Installation Instructions sheet, you can receive one by

visiting GEAppliances.com or by calling 800.GE.CARES (800.432.2737).

• Install or store where it will not be exposed to

temperatures below freezing or exposed to the

weather, which could cause permanent damage and

invalidate the warranty.

• Properly ground washer to conform with all

governing codes and ordinances. Follow details

in Installation Instructions.

• To ensure proper installation, run two small load size

Speed Wash cycles BEFOREwashing the first load.

• This washer does not include water supply hoses.

GE strongly recommends the use of factory specified

parts. A list of factory hoses available for purchase

are listed below. These hoses are manufactured and

tested to meet GEspecifications.

GEstrongly recommends the use of new water

supply hoses. Hoses degrade over time and need to

be replaced every 5 years to reduce the risk of hose

failures and water damage.

Parts and Accessories

Order on-line at GEAppliances.com today, 24 hours

a day or by phone at 800.626.2002 during normal

business hours.

Part Number

WH41X10207

Accessory

4 ft RubberWater SupplyHoses

WX14X10005 4 ft Braided Water Supply Hoses

YOURLAUNDRYAREA

• Keep the area underneath and around your

appliances free of combustible materials such as

lint, paper, rags, chemicals, etc.

• Close supervision is necessary if this appliance is used

by or near children. Do not allow children to play on,

with or inside this or any other appliance.

GEAppliances.com

Use this

appliance

only for its

intended

purpose as

described in

this Owner's

Manua/

WHEN USINGTHEWASHER

Never reach into the washer while it is moving,

Wait until the machine has completely stopped

before opening the lid,

Do not mix chlorine bleach with ammonia or acids

such as vinegar and/or rust remover, Mixing different

chemicals can produce a toxic gas which may cause

death,

Do not wash or dry articles that have been cleaned

in, washed in, soaked in or spotted with combustible

or explosive substances (such as wax, oil, paint,

gasoline, degreasers, dry-cleaning solvents, kerosene,

etc,),These substances give off vapors that may

ignite or explode, Do not add these substances to the

wash water, Do not use or place these substances

around your washer or dryer during operation,

The laundry process can reduce the flame retardancy

of fabrics, To avoid such a result, carefully follow the

garment manufacturer's wash and care instructions,

To minimize the possibility of electric shock, unplug

this appliance from the power supply or disconnect

the washer at the building's distribution panel by

removing the fuse or switching off the circuit breaker

before attempting any maintenance or cleaning,

NOTE: Turning the Cycle Selector/{nob to an off

position, or pressing PAUSEdoes NOT disconnect the

appliance from the power supply,

Never attempt to operate this appliance if it is

damaged, malfunctioning, partially disassembled, or

has missing or broken parts, including a damaged

cord or plug,

WHENNOTIN USE

•Turn off water faucets to minimize leakage if a break

or rupture should occur, Check the condition of the fill

hoses; GErecommends changing the hoses every 5

years,

•Before discarding a washer, or removing it from

service, remove the washer lid to prevent children

from hiding inside,

•Do not attempt to repair or replace any part of

this appliance unless specifically recommended in

this Owner's Manual, or in published user-repair

instructions that you understand and have the skills

to carry out,

•Do not tamper with the controls,

READAND SAFETYINFORMATIONCAREFULLY

LoLLowrills

SAVETHESEINSTRUCTIONS

About the control panel-for models with STARTbutton.

• Add fabric softener Ion

models with afabric softener

dispenser); see page 6 for

details

• Add detergent. GE

recommends the use of High

Efficiency _ detergents in

all Energy Star-rated washers

Step

• Add items

• Close lid

NOTE:Washer will not start

to fill with lid open on Auto

Load sensing settings Ion some

models}

Step 4

• Select load size and

other wash options,

including Fabric

Softener option

• Select wash cycle

• Select OPTIONS

• Push START

Quick Start Guide

LOAD SIZE

OR SIGNAL TEMPERATURE OPTIONS 00000

FILL SOAK WASH RINSE SPIN

Controls

START

STOP/PAUSE

El II

AUTOMATICLOAD

SENSINGequipped

models

LoadSize(onsomemodels)

• Add _ detergent to the bottom of the basket and fabric softener to the dispenser prior to loading clothes,

• Loosely load items in the washer basket, Overloading may negatively impact wash performance,

Adjust the load size accordingly,

• Makethe load selection:

For AUTOMATICLOADSENSINGequipped models

- Forconvenience, best performance and optimal efficiency, selectAUTOMATICLOADSENSING,This selection

automatically providesthe correct amount of water suited to the size and type of load placed in the unit,

- Ifyou prefer to manually selectthe water level,select SMALLthrough SUPER,While AUTOMATICLOADSENSINGis

best for most loads and general washing, you may want to manually select the load size for specialty items such

asbulky, lightweight comforters or pillows,where you want to ensurea larger water levelis applied, Manual load

sizeselections should be made for wet items placed inthe washer, such as soaked towels or garments,

- The washer will not fill with water when automatic load sensing is selected if the lid is opened,

When the lid is closed the machine is able to begin filling with water in order to sense the load size,

NOTE:This isa high-efficiency washing machine,This system requires lesswater while providing effective cleaning

action,You may notice that the water level is lower than on your previous washer, This isnormal,

Signal (on some modeN

• Select for an end of cycle signal,

GEAppliances.com

Temperature

Selectthe water temperature for the wash and rinse cycles,Alwaysfollow fabric manufacturer's care labelor instructions when laundering,

PerfecTemp sensesthe incoming water temperature and adjusts the fillwater to obtain a more precisetemperature range for all wash

temperatures except TAPCOLD,Forexample, in a COLDwash selection, somewarm water may be added to reach a temperature

neededto better dissolve detergents, Often,detergents are not completely dissolved in very cold water, especially in cooler climates,

Duringwinter months, when the water entering your home iscolder, or for locations with very cold water year round, usethe PerfecTemp

COLDto help dissolve powdered detergents andto improve the cleaning of your clothes,

The TAPCOLDfeature turns the PerfecTemp feature on your washer off and usesyour household tap water temperature for a COLD

wash, This can provide energy savings byreducing the amount of hot water usedin your wash,

Options

Autosoak Option (on some models)

This option begins with a brief agitation, soaks for a specified period of time, then moves through the rest of the cycle

automatically, On some models, this option is located on the Cycle Selector knob,

2nd Rinse Option (on some models)

When you use extra detergent or bleach to clean heavily soiled clothes, use the 2nd Rinse option to better remove additional

residues,

Extended Spin Option (on some models)

Use this option to extract more water from your clothes, Clothes will be drier when this option is selected and will dry more

quickly in your dryer,

Fabric Softener and Power Rinse

Set this option when adding fabric softener to the washer or to select the enhanced Power Rinse,

NOTE: Do not use fabric softener dispensing balls with this washer, They do not work correctly in high-efficiency washers,

Status Indicator Lights

The Cycle Indicator Lights show what stage the washer is in, When the Selector knob isset to a new cycle, the Indicator

Lights will flash momentarily, showing what stages the cycle will go through, On models without an AUTO SOAK option, the

SOAK lightwillnotlightup, I 0 0 0 0 0

IFILL SOAK WASH RINSE SPIN

Wash Cycle--Cycle Selector Knob

The wash cycle controls the length and intensity of the washing process, The knob can be turned in either direction, Turning

the Cycle Selector knob after starting a cycle will stop the washer and reset the cycle to the new selection, PressSTARTto

begin the new cycle selection,

WHITES For heavy to lightly soiled cottons, household linens, work and play clothes, This cycle provides the best overall

cleaning and should be used for most everyday items, Provides a regular wash and a high speed spin,

PREWASH For removing surface dirt from heavily soiled clothes, Make sure to follow with a regular wash cycle,

COLORS For non-colorfast cottons and blends or items that are labeled cold wash, Provides a regular wash with periods of

soak and a high speed spin,

PERMANENT PRESS For wrinkle-free and permanent press items and knits, Provides a regular wash with periods of

soak and a low speed spin,

DELICATES For lingerie and special-care fabrics with light soil, Provides an extra gentle wash and a low speed spin,

HAND WASH For items labeled hand washable with light soil, Provides an extra low speed spin,

SPEED WASH For small loads of lightly soiled items that are needed in a hurry, Provides a high speed spin,

DRAIN &SPIN OR SPIN ONLY For draining the tub and spinning water out of the clothes, Provides a high speed spin,

TOWELS & SHEETS Provides periods of agitation and soak tailored for washing towels and sheets, Provides a regular wash

and a high speed spin,

JEANS For washing medium to lightly soiled jeans, Provides a gentle wash and a high speed spin, (For heavily soiled work

jeans, use WHITES cycle,)

QUICK RINSE Rinses and spins non-soiled items where a rinse only is desired, Provides a high speed spin,

START

Press START to begin the cycle, Pressing START again will PAUSE the cycle and the Cycle indicator light will blink,

To continue the cycle, press STARTagain or close the lid, If machine is paused more than 24 hours, the cycle will be

cancelled, To stop the cycle, hold the button for 3 seconds, If water remains in the machine, select the DRAIN & SPIN

OR SPIN ONLY cycle to drain tub and spin water out of the washer tub,

Raising the lid will stop agitation or spin action but does not pause the cycle,

About washer features.

OPTIONS

OFF

2nd Set when adding

RINSE FABRIC SOFTENER

EXT FABRIC SOFTENER

SPINAQoFTENER2nd RNS & X NOD S_N

x NODS _,X AUTO 2rid RNS

SOAK

The Fabric Softener Dispenser

The agitator cap fits into the top of the agitator,

If it accidentally comes off, simply put it back

on,

r31 Add water to dispenser until it reaches the

maximum fill line,

The fabric softener dispenser automatically

releases liquid fabric softener at the proper time

during the cycle,

Do not stop the washer or raise the lid during

the first spin. This will cause the dispenser to

emptg too soon.

Touse, follow these steps."

-_'-I ake sure dispenser is securely attached to

agitator,

Do not pour anything into the

agitator if the agitator cap or

dispenser is removed.

r_l Use only liquid diluted fabric softener, Pour r_--ISelect FABRIC SOFTENER setting knob to

into dispenser, using amount recommended --activate the cycle,

on package, Note:Fabric softener will not dispense if the

Never pour fabric softener directly on clothes, knob is in the OFF "position,

It mag stain them.

Separate for cleaning

Cleaning the Fabric Softener Dispenser (onsome models)

I-1"1Remove the dispenser from the top of the agitator,

r_-i Separate the dispenser cup from the cover by grasping the top and pushing down on the

inside of the cup with your fingers, Dispenser cup will pop free from the cover,

r3-1 To clean the dispenser, soak both the dispenser cup and the dispenser cover in the following

solution:

•7USgallon (3,8 liters) warm water

• 7/4cup (60 ml) heavy-duty liquid detergent

•7cup (240 ml) bleach

4-1If necessary, loosen buildup with a clean, soft cloth after soaking, Do not use a stiff brush; you

may roughen the surface of the dispenser,

r-5-1Rinse and reassemble dispenser, Place dispenser back on the agitator,

Liquid Bleach Funnel

The water fill dilutes liquid chlorine bleach as the washer fills for the wash cycle,

I-1"1Check clothing care labels for special instructions,

r2-1 Measure liquid bleach carefully, following instructions on the bottle,

•Neverpour undiluted liquid chlorine bleach directly onto clothes or into the wash basket,

•Do notpourpowdered bleach into bleach funnel,

Before starting the washer, pour measured amount of bleach directly into bleach funnel, Avoid

splashing or over-filling dispenser, Ifyou prefer to use powdered bleach, add it into the wash

basket with your detergent,

• Do not mix chlorine bleach with ammonia or acids such as vinegar and/or rust remover,

Mixing can produce atoxic gas which may cause death,

Loading and using the washer.

Always follow fabric manufacturer's care label when laundering.

GEAppliances.com

Sorting WashLoads

Sort by color (whites, lights, colors), soil level,

fabric type (sturdy cottons, easy care, delicates)

and whether the fabric produces lint (terry cloth,

chenille) or collects lint (velveteen, corduroy),

Proper Use of Detergent

Add detergent before adding items so that the

detergent can work effectively, Using too little or

too much detergent is a common cause of laundry

problems,

For spots, apply pre-treatment to items as

recommended on the product label, Application

should be made in the basket to prevent overspray

which may cause the coloring on the lid or graphics to

fade,

You can use less detergent if you have soft water,

a smaller load or a lightly soiled load,

When using high efficiency or concentrated

detergents, consult the product label to determine

amount required for optimum performance, Excessive

detergent will negatively impact wash performance,

Loading the Washer

Load dry items loosely in the washer basket, For best

results, load items evenly and loosely around the

outside of the basket, To add items after washer has

started, lift the lid and submerge additional items

around the outside of the basket,

•Do not place large items across the/nfusof M Load

them around the outside of the basket,

• Do not wash fabrics containing flammable materials

(waxes, cleaning fluids, etc,),

• Washer will not agitate or spin with the lid up,

however the timer will continue to run,

Care and cleaning of the washer.

Wash Basket: Leave the lid open after washing to allow

moisture to evaporate, If you want to clean the basket, use

a clean, soft cloth dampened with liquid detergent; then

rinse, (Do not use harsh or gritty cleaners,)

Fill Hoses: GErecommends changing the hoses every 5

years,

Exterior: Immediately wipe off any spills, Wipe with damp

cloth, Try not to hit surface with sharp objects,

Interion The occasional use of a cycle that contains bleach

will keep the inside of the washer clean,

Moving and Storage: Ask the service technician to remove

water from drain pump and hoses, Seethe Installation

Instructions packed with product for information on how

to reinstall the shipping rod to keep the tub stationary

when moving the washer, For more information, visit

GEAppliances.com or call 800.GE.CARES(800,432,2737),

Do not store the washer where it will be exposed to the

weather,

Long Vacations: Be sure water supply isshut off at

faucets, Drain all water from hoses if weather will be below

freezing,

Before you call for service...

Troubleshooting Tips

Save time and money! Review the charts on the following pages,

or visitGEAppliances.com. Youmay not need to call for service.

WATER Possible Causes What To Do

Water level seems low Thisis normal •Water may not cover the top levelof the clothes.

Thisis normal for this high-efficiency washer,

Water fills and drains Drain stand pipe istoo low • Thedrain stand pipe must be above 30".

at the same time

Too many suds Too much detergent • Measure your detergent carefully. Uselesssoap ifyou have

soft water, a smaller loador a lightly soiledload,

Tgpe of detergent • Switchto HE_detergent,

Softwater • Try lessdetergent.

Water leaks Using too much detergent • Use lessdetergent. Uselesssoap ifyou havesoft water.

in washer a smaller load or a lightly soiled load,

Tgpe of detergent ° Switchto HEall, detergent,

Fill hoses or drain hose is ° Make sure hoseconnections are tight at faucets and

improperly connected rubber washers are installed,Make sureend of drain hose

iscorrectly inserted in and secured to drain facility,

Household drain mag ° Checkhousehold plumbing. You may needto call

be clogged a plumber,

Drain hose is loose ° Makesure drain hoseisfully seated in back of washer and

that the two retaining screws are fully seated,

Drain hose rubs on wall • Makesure drain hosedoes not make contact with the wall.

May cause excessivewear on the hose,

Constant water pressure ° Tightenhoses at the faucets and turn the water off after

to the fill hosesat the each use,

water source ° Checkcondition of the fill hoses;they should be replaced

every 5 years,

Water temperature Cooler water temperatures ° New laundry detergents have been formulated to work

seems incorrect provide improved energg with cooler water temperatures without affecting wash

efficiencg performance,

Water supplgisturned off • Turn both hot and coldfaucets fully on and make sure

or improperlg connected hoses are connected to correct faucets,

Water valve screensare • Turnoff the water source and remove the water connection

stoppedup hosesfrom the upper back of the washer, Usea brush or

toothpick to clean the screens inthe machine, Reconnect

the hosesand turn the water back on,

Cool/Cold water when • Thisis normal. PerfecTempsenseswater temperature and

selectingHot optimizes for best results, Coldwater isadded periodically

when hot isselected,

House water heater is ° Makesure housewater heater isdeliveringwater at

not set properlg 120°F-140°F(48°C-60°C),

Water pumped out before Lid lifted or cgclewas put in ° Resetcycle.

cgcle is complete pause for over 24 hours

Water won't drain Drain hose is kinked or • Straighten drain hoseand make surewasher isnot sitting on it.

improperlg connected • Topof drain outlet should be lessthan 6 ft (1.8m)above floor.

Washer pauses during The PREWASHCgcle • This is normal. The washer alternates between agitate and

wash cgcle was chosen soak during these cycles to getyour clothes cleaner with

lesswear,

Washer pauses during This is normal • Thewasher may pause during the spin cycleto remove

spin cgcle soapy water more efficiently,

GEAppliances.com

OPERATION Possible Causes What To Do

Washer won't operate Washer is unplugged • Make sure cord is plugged securely into a working outlet.

Water supply is turned off • Turn both hot and cold faucets fully on.

Controls are not set properly • Check controls.

Lid is openisafety feature • Close lid and reset cycle, to the beginning if necessary.

prevents agitation and

spinning when lid is up

Circuit breaker/fuse is • Check house circuit breakers/fuses. Reploce fuses or

tripped/blown reset breaker. Washer should have a separate outlet.

Electronics need to be reset • Unplug washer, wait 2 minutes, plug back in and press START.

STARTwas not pressed • Press START.

Lid magnet missing •Call for service.

Time not shown Unit filling • This is normal. Estimated time remaining is updoted during

on display fill time.

Movement inside machine Shifting mechanism is • When the machine is manuolly turned off, the shifter will

when shut off disengaging the motor disengage the motor before completely shutting down.

If lid is raised before the motor isdisengaged, it will resume

when lid is closed.

PERFORMANCE Possible Causes What To Do

Clothes too wet Incorrect cycle selected. •Hoke sure the cycle selected motches the Iood you ore

washing. Somefabrics will feel wetter when rinsed with cold water.

Wash load out of balance • Redistribute load in washer and run through Drain & Spin cycle.

Colored spots Incorrect use of fabric • Check fobric softener package for instructions and follow

softener directions for using dispenser.

• Make sure you hove selected the Fabric Softener option.

• Pretreat stain and rewash.

Dye transfer • Sort whites or lightly colored items from dork colors.

Grayed or yellowed Detergent amount • Be sure to follow detergent manufacturer's directions.

clothes Hard water • Use a water conditioner like Calgon brand or install

a water softener,

Water is not hot enough • Moke sure water heater is delivering water at

120°%140°F (48°C-60°C).

Washer is overloaded • Loosely load clothes in the washer basket. Adjust Iood size based

on item size and material. For best results, load items around the

outside of the basket.

Detergent is not dissolving • Add detergent before you load items.

Dye transfer • Sort clothes by color. If fobric Iobel states wash separately,

unstable dyes may be indicated.

Lint or residue on Clothes are air or line dried • If you do not dry your clothes with a clothes dryer, your

clothes clothes may retain more lint.

Incorrect sorting • Separate lint producers from lint collectors.

Washing too long • Wash small Ioods for a shorter time than Iorger Ioods.

Detergent not dissolving • Add detergent before you Iood items.

• Try a liquid detergent

• Use warmer water temperature.

Overloading • Loosely Iood clothes in the washer basket Adjust load size based

on item size and material For best results, load items around the

outside of the basket

Incorrect use of fabric

softener • Check fobric softener package for instructions and follow

directions for using dispenser

• iVlokesure you have selected the Fabric Softener option

Before gou call for service...

Troubleshooting Tips

PERFORMANCE (cont.) Possible Causes Reason

Pilling Result of normal wear on • Whilethis is not caused by the washer, you can slow the

polg-cotton blends and pilling processbywashing garments insideout.

fuzzy fabrics

Snags, holes, tears, rips Pins,snaps,hooks,sharp • Fastensnaps,hooks,buttons and zippers.

or excessivewear buttons, belt buckles, •Removelooseitems likepins,objects in pockets and

zippers and sharp objects sharp buttons.

left in pockets • Turn knits(which snag easily)inside out.

Undiluted chlorinebleach • Checkbleach package instructions for proper amount.

• Never add undiluted bleachto wash or allow clothes to

come in contact with undiluted bleach.

Chemicals like heir bleach or • Rinseitemsthat may havechemicals on them before

dye, permanent wave solution washing.

Wrinkling Improper sorting • Avoid mixing heavy items (likework clothes)with light items

(likeblouses).

• Try o fabric softener.

Overloading or incorrect • Loosely load clothes in the washer basket, Adjust load size based

water level on item sizeand material.

Incorrect wash and • Match Cycleselectionto the type of fabric you ore washing

dry cycles (especiallyfor easy care loads).

Repeated washing in • Wash inworm or cold water.

water that istoo hot

SOUNDS Possible Causes What To Do

"Metallic clicking" Shifter mechanism is • Thedrive systemwill engage at the start of agitate and

engaging or disengaging disengage when agitate iscomplete. This occurs multiple

times during the wash.

Back and forth "swoosh" Electricmotor reversing • Thismachine has u drivesystem that doesn't use gears.

or light "clicking" sound direction Thissound isthe motor rotating back and forth to clean

during agitate your laundry.

Quick short agitation Clothing redistribution • Atthe end of agitate, the motor makes short agitation strokes

soundsat end of agitate to redistribute the load.

"Click" when water Relay switch • Therelay makes a click sound when activated.Thewater

stops filling levelactivates the relay and stopsfilling.

"Clicking" behind Control Automatic Temperature • Twovalvesmix cold and hot water. The "clicking" iswhen either

Panel during fill Control Valve valve turns on or off to raiseor lower the fillwater temperature.

Water flow changes Automatic Temperature • Two valvesmix cold and hot water. Theflow changes when either

during fill Control Valve valve turns on or off to raise or lower the fillwater temperature.

Motor "whining up" or Motor ramping up/down • Themotor will speed up incrementally during the spin cycle.

"coasting down" in spin during spin cgcle When spin iscomplete, itwill coast until it stops.

"Humming" Water drain pump • Thedrain pump will make a humming sound when pumping

out water after agitation stops and continue until spin iscomplete.

"Gurgling" Water drain pump • When the pump starts drawing in air,It starts to gurgle.

Thewasher shouldthen begin spinning and the sound will

continue until it isdone spinning.

Water "swishing" This is normal • Thiswasher usesa InfuserTM wash action.Water swishingwhile

the unit isagitating isnormal,especiallywith smaller loads.

Washer is noisy Washer is uneven • Tolevelthe front of the washer, adjust the front leveling legsby

rotating the individual leg inthe proper direction for up

or down. Tolevelthe back of the washer, lift the back

of the machine 4" (11cm) and set down.

Shipping rod is still assembled • Toremove the shipping rod from the washer, pullthe yellow tag

in the unit and remove the attached rod from the bottom right hand sideof

the washer.

Andere Handbücher für Appliances G153

Inhaltsverzeichnis

Andere GE Waschmaschine Handbücher

GE EWA2500 Bedienungsanleitung

GE WJRE5550HWW Bedienungsanleitung

GE Profile Harmony WPGT9360 Anleitung zur Verwendung

GE WSLS1100 Anleitung zur Verwendung

GE Profile ENERGY STAR WPDH8800J Montageanleitung

GE Spacemaker WSKS2060 Bedienungsanleitung

GE WHRE5550H2WW Bedienungsanleitung

GE WCVH6800JMS - 27" Front-Load Washer Montageanleitung

GE WNCK2050DWC Bedienungsanleitung

GE Profile PFWS4605LMG Montageanleitung

GE GTWN5450DWW Bedienungsanleitung

GE WWA8800M Bedienungsanleitung

GE Profile WPGT9350 Anleitung zur Verwendung

GE Appliances GFWH1200 Originalbetriebsanleitung

GE WJRE5550HWW Bedienungsanleitung

GE GTWN4250DWS Bedienungsanleitung

GE GTWN4250MWS Montageanleitung

GE WPSE7003 Bedienungsanleitung

GE GFWN1100L Originalbetriebsanleitung

GE WPGT9150HWW - Profile 27" Washer Handbuch

GE GE Profile WCCB1030FWC Bedienungsanleitung

GE WA5857R Bedienungsanleitung

GE SH208 Bedienungsanleitung

GE G005 Bedienungsanleitung

Beliebte Waschmaschine Handbücher anderer Marken

Tricity Bendix

Tricity Bendix AW 1000 W Produkthandbuch

Panasonic

Panasonic NA-F60L5WRB Bedienungsanleitung

Electrolux

Electrolux EWF1284EDW Bedienungsanleitung

LG TV2516DV3B Bedienungsanleitung

LG TH2517DSAV Bedienungsanleitung

VESTEL

VESTEL CMH-XL 7510 TE Bedienungsanleitung

AEG

AEG 74335 Bedienungsanleitung

Johnson

Johnson JWF721A Bedienungsanleitung

Beko

Beko WTE7604XLW0 Bedienungsanleitung

Danby

Danby DTT100A1WDB Montageanleitung

Amica

Amica WA 14 Ex Bedienungsanleitung

Daewoo

Daewoo DWD-F1222 Bedienungsanleitung

Bosch

Bosch WAS28461AU Bedienungsanleitung

Miele

Miele PW 6080 Vario Bedienungsanleitung

Finlux

Finlux FLX108CF220 Bedienungsanleitung

Whirlpool

Whirlpool 3LBR5132AN0 Bedienungsanleitung

Beko

Beko WKB 51231 PTMA Bedienungsanleitung

Samsung

Samsung WF16J9800K Series Bedienungsanleitung