GE AvantaPure Professional Series Bedienungsanleitung

Models: 268 Co-Current Conditioner

263 Three-Cycle Filter

AvantaPure®Professional Series

Water Treatment System by GE

Operations Manual

Writers Note: NEED NEW IMAGE

2 Table of Contents

Rev H

Table of Contents

How To Use This Manual 3

General Warnings And Safety Information 4

System Operation Cycle Functions 6

Equipment Installation 8

Valve Layout 8

Control Layout 9

Location Selection 11

Water Line Connection 17

Drain Line 20

Regenerant Line Connection 21

Overflow Line Connection 23

Electrical Connection 25

Valve Camshaft 28

Disinfection Of Water Conditioners 29

AvantaPure Controller 31

Display Icons 32

Keypad — Buttons 33

Things You Might Need to Know 34

Programming Overview 35

Level I Programming 35

Level II Programming 37

Level III Programming 43

Placing Conditioner Into Operation 44

AvantaPure Exploded View 47

AvantaPure Parts List 48

Troubleshooting 49

How To Use This Manual 3

Rev H

How To Use This Manual

series controllers.

This manual is a reference and will not include every system installation

situation. The person installing this equipment should have:

• Training in the AvantaPure series controllers and Autotrol brand valves

• Knowledge of water conditioning and how to determine proper control

settings

• Basic plumbing skills

• The directional instructions "left" and “right" are determined by looking

at the front of the unit.

Icons That Appear In This Manual

Introduction

Parts Included

Left Side Right Side

WARNING: Failure to follow this instruction can result in personal injury

or damage to the equipment.

NOTE:

4 General Warnings And Safety Information

General Warnings And Safety Information

Electrical

There are no user-serviceable parts in the AC adapter, motor, or controller.

In the event of a failure, these should be replaced.

• All electrical connections must be completed according to local codes.

• Use only the power AC adapter that is supplied.

• The power outlet must be grounded.

• To disconnect power, unplug the AC adapter from its power source.

• Do not use petroleum based lubricants such as vaseline, oils, or

hydrocarbon based lubricants. Use only 100% silicone lubricants.

• All plastic connections should be hand tightened. Teflon tape may be

used on connections that do not use an O-ring seal. Do not use pliers

or pipe wrenches.

The drain line must be a minimum of 1/2-inch diameter. Use

3/4-inch pipe if the backwash flow rate is greater than 7 GPM

(26.5 Lpm) or the pipe length is greater than 20 feet (6 m).

• Do not support the weight of the system on the control valve fittings,

plumbing, or the bypass.

• It is not recommended to use sealants on the threads. Use Teflon*

tape on the threads of the 1-inch NPT elbow, the drain line

connections, and other NPT threads.

*Teflon is a trademark of E.I. duPont de Nemours.

CAUTION:

Rev H

General

• Observe all warnings that appear in this manual.

• Keep the media tank in the upright position. Do not turn upside down

or drop. Turning the tank upside down will cause media to enter the

valve.

• Operating ambient temperature is between 34F (1C) and 120F

(49C).

• Operating water temperature is between 34F (1F) and 100F (38C).

• Working water pressure range is 20 to 120 psi (1.38 to 8.27 bar). In

Canada the acceptable working water pressure range is 20 to 100 psi

(1.38 to 6.89 bar).

• Use only regenerant salts designed for water softening. Do not use ice

melting, block, or rock salts.

• Follow state and local codes for water testing. Do not use water that is

microbiologically unsafe or of unknown quality.

• When filling media tank, do not open water valve completely. Fill tank

slowly to prevent media from exiting the tank.

• When installing the water connection (bypass or manifold) connect to

the plumbing system first. Allow heated parts to cool and cemented

parts to set before installing any plastic parts. Do not get primer or

solvent on O-rings, nuts, or the valve.

WARNING: The valve and tank components of this unit have been

assembled and tightened to the proper factory torque specifications.

Over tightening may result in improper valve, probe and tank alignment

and may damage the tank O-ring

(PN 1010154).

WARNING: Excessive Weight Hazard. Use two or more people to move

and install the conditioner. Failure to do so can result in injury (including

back injury).

6 System Operation Cycle Functions

System Operation Cycle Functions

1. Service (Downflow)

2. Backwash (Upflow)

3. Brine/Slow Rinse (Downflow)

4. Repressurized Cycle (Hard Water Bypass Flapper Open)

5. Fast Rinse (Downflow)

6. Brine Refill

Rev H

Cycle Water Flows

SERVICE BACKWASH BRINE/SLOW RINSE

FAST RINSE

From Regenerant

Tank

To Regenerant

Tank

BRINE REFILL

REPRESSURIZE

8 Equipment Installation

Equipment Installation

Valve Layout

Refill Controller

Regenerant Tube Connection

Injector and cap

Valve Discs

Outlet

Drain

Inlet

Backwash Injector Screen

Camshaft

Drain Control Filter

Control Module

Mount

One Piece Valve

Disc Spring

Motor

Optical Sensor

Control Layout 9

Rev H

AvantaPure Controller

LBS

MIN

x100

LCD Display

Manual Regen Button

Down Button

Set Button Up Button

For Future Use

Turbine Input or Dry Contact Signal Input

Main Motor &

Optical Sensor

Connection

AC Adapter

(low voltage)

Input

Chlorine Generator Outlet

Rev H

Model Number

Recharge Style

Media Tank Size

Resin Volume

Recharge (Salt) Tank Size

Salt Storage

Drain Water Rate

Service Connection Size

Drain Connection Size

Recharge (Brine) Connection Size

Installation Space Requirements

Shipping Weight

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere GE Wasserfiltersystem Handbücher

GE SmartWater FX12M Bedienungsanleitung

GE Replacement Filter Bedienungsanleitung

GE GXRV40TBN Bedienungsanleitung

GE Culligan FXRT12 Bedienungsanleitung

GE GNSV70RBL Betriebsanleitung

GE PXRQ400T Originalbetriebsanleitung

GE AFPWF Bedienungsanleitung

GE GNSV65RBL Bedienungsanleitung

GE Merlin Handbuch

GE Osmonics F-801 Bedienungsanleitung

GE SmartWater GX1S01C Bedienungsanleitung

GE Pro Elite 268-716-150-1248 Bedienungsanleitung

GE GXSV65F Betriebsanleitung

GE GXSL55F Betriebsanleitung

GE GXPL03D Bedienungsanleitung

GE SmartWater GNWH08C Bedienungsanleitung

GE GQ1S50F Originalbetriebsanleitung

GE Smart Water PNRV18ZWH01 Bedienungsanleitung

GE GQSL55F Betriebsanleitung

GE GXFM07HBL Bedienungsanleitung

GE SmartWater GXUT05Z Bedienungsanleitung

GE SmartWater GXWH35F Bedienungsanleitung

GE GN1S15CBL (REV. 2) Service-Handbuch

GE GXK185KBL Originalbetriebsanleitung

Beliebte Wasserfiltersystem Handbücher anderer Marken

Wisy

Wisy LineAir 100 Bedienungsanleitung

Schaffner

Schaffner Ecosine FN3446 Series Betriebsanleitung

Pentair

Pentair FLECK 4600 SXT Benutzerhandbuch

H2O International

H2O International H20-500 Bedienungsanleitung

Renkforce

Renkforce 2306241 Bedienungsanleitung

Neo-Pure

Neo-Pure TL3-A502 Bedienungsanleitung

FLTR

FLTR OBF Bedienungsanleitung

STA-RITE

STA-RITE VERTICAL GRID DE FILTERS S7D75 Bedienungsanleitung

Applied Membranes

Applied Membranes W-G844EM Bedienungsanleitung

BEGA

BEGA 116 Bedienungsanleitung

WATA

WATA Standard Bedienungsanleitung

Price

Price FFU series Handbuch

Gaggenau

Gaggenau BRITA INTENZA 467873 Bedienungsanleitung

Brita

Brita SAFF-100 Bedienungsanleitung

HEISSNER

HEISSNER FPU24000-00 Bedienungsanleitung

BGS technic

BGS technic 1518 Bedienungsanleitung

Reverse Osmosis

Reverse Osmosis RF Series Bedienungsanleitung

ubbink

ubbink Filtramax Series Bedienungsanleitung