GE Osmonics E4H-CE Series Gebrauchs- und Wartungshandbuch

E4H-CE AND E8-CE SERIES

WATER PURIFICATION

MACHINES

3 m3/hr to 45 m3/hr

18,000 gpd to 288,000 gpd

Control Narrative

Manual

GE OSMONICS E4H-CE AND E8-CE WATER

TREATMENT SYSTEMS

CONTROL NARRATIVE

MANUAL

TABLE OF CONTENTS

Page

1.0 OVERVIEW 1

1.1 Hardware 1

1.2 Software 1

1.3 Operator Interface Terminal (OIT) 2

2.0 START-UP 3

2.1 Operation Screen 4

2.2 Alarm History Screen 6

2.3 Machine Status Screen 8

2.4 Utilities Screen 10

2.5 Set-Up Screen 11

LIST OF FIGURES

Figure Title

2.1 Start-Up Screen 3

2.2 Operation Screen 4

2.3 Alarm History Screen 6

2.4 Machine Status Screen 8

2.5 Utilities Screen 10

2.6 Set-Up Screen 11

LIST OF TABLES

Table Title

2.1 Alarm Messages 7

2.2 Status Screen System Message 9

1.0 OVERVIEW

The GE Osmonics E4H-CE and E8-CE water treatment systems consist of modular equipment that

is designed to work together with the reverse osmosis (RO) machine at the heart of the system.

The Programmable Logic Controller (PLC) and Operator Interface Terminal (OIT) are pro-

grammed to control a complete, integrated system. A water purification system may consist of the

following modular equipment:

· Media Filter(s)

· Chemical Injection System

· Clean-In-Place (CIP) System

· Permeate Storage Tank

Your system may or may not contain all of the modular equipment listed above. To accommodate

the variations possible, the control system is designed to allow the user to operate with any of the

components list above.

1.1 Hardware

A SIEMENS S7-222 PLC, located in the control enclosure, controls the system. Operator

interface is done with a SIEMENS TP070 OIT mounted on the enclosure door. A Hanna

Instrument 983320 Conductivity Meter and a 981411 pH Meter provide display of oper-

ating conditions as well as alarm and control set points.

Electrical enclosure door mounted lights and switches are as follows:

POWER ON: A clear light which indicates that the control voltage is applied to the

enclosure panel.

E-STOP: A latching push-button switch that will interrupt power to the PLC

outputs and inputs causing the system equipment to immediately

shut down. In case of an emergency, using this push button will

bypass the normal shutdown procedure required to safeguard the

equipment. The E-STOP switch must be pulled out and the E-STOP

RESET button and the alarm reset button on the OIT pushed to

restore power to PLC inputs and outputs and restart the machine.

The E-STOP is lit when it is engaged and the control relay is not

powered.

E-STOP RESET: A momentary push-button switch that will restore power after the E-

STOP switch has been pushed (latched) and pulled out (unlatched).

1.2 Software

The SIEMENS S7222 PLC is programmed with SIEMENS Step 7-Micro Programming

Software. The SIEMENS TP070 OIT is programmed with SIEMENS STEP 7-Toolbox

Programming Software.

1.3 Operator Interface Terminal (OIT) Screen

The available screens for the PanelView are as listed:

START-UP: Contact information for customer.

OPERATION: Gives run options for machine, alarm, and status messages.

ALARM HISTORY:Displays last five alarms conditions.

STATUS: Displays last five operating conditions.

UTILITIES: Adjusts contrast, screen center, and allows user to clean dis-

play.

SET-UP: Allows user to clear alarm history, run time, and status.

Allows user to download new program information.

2.0 START-UP

The START-UP Screen is displayed upon start-up of the E-CE Series RO machine. This touch

screen gives customer contact information.

Figure 2.1

Start-Up Screen

To get to the next screen, press anywhere on the screen or wait twenty (20) seconds.

2.1 Operation Screen

The Operation Screen displays the control function for the E-CE Series RO machine.

Figure 2.2

Operation Screen

NO. FUNCTION OPERATION

1 RO Switches machine to run

2 AUTO/HAND Switches machine to Auto

or Hand

3 CIP Switches machine to CIP mode

4 FILL Energizes the inlet solenoid valve

to fill machine

5 PURGE Manually puts RO machine into

Permeate Purge

6 AUTO/HAND Switches the Permeate Purge to

Auto or Hand

NO. FUNCTION OPERATION

7 INFORMATION Takes User to Information Screen

8 ALARM Takes User to Alarm Screen

9 ALARM RESET Resets current Alarm

10 UTILITIES Takes User to Utilities Screen

11 ALARM Displays current Alarm condition

MESSAGE

12 SYSTEM Displays current Operating

conditions

The RO machine is controlled using the Operation Screen. The FILL button energizes the

inlet solenoid valve allowing the RO machine to fill water. The machine will run for ten

(10) minutes filling the machine. This needs to be done before the RO machine can oper-

ate. Once the machine has been filled the RO, CIP, and PURGE buttons will operate.

The RO button controls the RO machine when it is in Run Mode. If the RO machine is

not in Run Mode, the RO button switches the RO machine from its current condition to

Run Mode. In the AUTO position the RO machine will shut down without going into

Permeate Purge.

The CIP button controls the RO machine when it is in CIP Mode. If the machine is not in

CIP Mode, pressing this button (CIP) will switch the machine from its current mode to CIP

Mode. See the Operation and Maintenance Manual (P/N 1161875) for details on running

CIP. If the machine is in CIP Mode, pressing the button shuts the RO machine down.

The PURGE Button controls the Permeate Purge Cycle of the RO machine. If the RO

machine is not in Purge Mode, pressing this button will switch the RO machine to

Permeate Purge for ten (10) minutes and then turn the machine OFF. If the RO machine

is in Purge Mode, pressing this button will shut down the machine.

The AUTO/HAND Button, located under the Purge Button, controls Permeate Purge oper-

ation. In the HAND position the RO machine will only go into Permeate Purge by man-

ually pressing the Purge Button. In the AUTO position, the RO machine will go into

Permeate Purge when the RO machine gets a signal from an external device, like a level

switch.

The ALARM Button takes the user to the ALARM HISTORY Screen, described later

(Section 2.3).

The INFORMATION Button takes the user to the MACHINE STATUS Screen, described

later (Section 2.4).

The UTILITIES Button takes the user to the UTILITIES Screen, described later

(Section 2.5).

The ALARM RESET Button is used to clear any alarm conditions, such as low inlet pres-

sure, high permeate pressure, or motor overload. This button needs to be pressed before

the RO machine will operate. The ALARM RESET Button on the Control Enclosure may

need to be pressed as well.

The SYSTEM message, located under the Control Buttons, shows the user the current sta-

tus of the machine. During shutdown, this message will display reason for shutdown.

2.2 Alarm History Screen

The ALARM Message, located above the Control Buttons, shows the user current Alarm

Conditions.

Figure 2.3

Alarm History Screen

NUMBER FUNCTION OPERATION

1 BACK Takes user back to OPERATION Screen

2 ALARM Takes user to ALARM Screen

3 ALARM RESET Resets current ALARM conditions

4 UTILITIES Takes users to UTILITIES Screen

5 ALARM HISTORY Displays the last 5 Alarm Conditions

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere GE Wasserfiltersystem Handbücher

GE SmartWater FX12P Bedienungsanleitung

GE SmartWater GXWH04F Bedienungsanleitung

GE Profile PNRQ15FBL Sicherheitsleitfaden

GE GXRV10ABL01 Sicherheitsleitfaden

GE Replacement Filter Bedienungsanleitung

GE Homespring UFC 100 Bedienungsanleitung

GE GXWH40L Bedienungsanleitung

GE GNUT03A Bedienungsanleitung

GE GXSL03B Sicherheitsleitfaden

GE SmartWater GXUT05Z Bedienungsanleitung

GE Smart Water PNRV18ZBB01 Bedienungsanleitung

GE GX1S01R Bedienungsanleitung

GE Profile PNRQ15FBL Gebrauchsanweisung

GE SmartWater GNSV75FWW Service-Handbuch

GE RPWF Bedienungsanleitung

GE Culligan FXRT12 Bedienungsanleitung

GE GXWH20S Bedienungsanleitung

GE PXRQ15F Sicherheitsleitfaden

GE Whatman Mini-UniPrep G2 Betriebsanleitung

GE GXSL55F Bedienungsanleitung

GE GXRV10ABL01 Sicherheitsleitfaden

GE PNRQ20RBL Originalbetriebsanleitung

GE PXRQ400T Originalbetriebsanleitung

GE PNRV12ZBL01 Bedienungsanleitung

Beliebte Wasserfiltersystem Handbücher anderer Marken

Wisy

Wisy LineAir 100 Bedienungsanleitung

Schaffner

Schaffner Ecosine FN3446 Series Betriebsanleitung

Pentair

Pentair FLECK 4600 SXT Benutzerhandbuch

H2O International

H2O International H20-500 Bedienungsanleitung

Renkforce

Renkforce 2306241 Bedienungsanleitung

Neo-Pure

Neo-Pure TL3-A502 Bedienungsanleitung

FLTR

FLTR OBF Bedienungsanleitung

STA-RITE

STA-RITE VERTICAL GRID DE FILTERS S7D75 Bedienungsanleitung

Applied Membranes

Applied Membranes W-G844EM Bedienungsanleitung

BEGA

BEGA 116 Bedienungsanleitung

WATA

WATA Standard Bedienungsanleitung

Price

Price FFU series Handbuch

Gaggenau

Gaggenau BRITA INTENZA 467873 Bedienungsanleitung

Brita

Brita SAFF-100 Bedienungsanleitung

HEISSNER

HEISSNER FPU24000-00 Bedienungsanleitung

BGS technic

BGS technic 1518 Bedienungsanleitung

Reverse Osmosis

Reverse Osmosis RF Series Bedienungsanleitung

ubbink

ubbink Filtramax Series Bedienungsanleitung