GEA ECOVENT Bedienungsanleitung

Operating Instructions

Hygienic valves

GEA ECOVENT® Valve Type W_/ECO

2023-05

430BAL014953

Original instructions

ted for damage resulting from non-observance of this document. If you have any ques-

tions or require clarication concerning the use of this document, contact the

Customer

service

Table of Contents

1 General

1.1 Information about the document 7

1.1.1 Purpose and structure of the document 7

1.1.2 Design elements 7

1.1.3 Reading obligation and storage 8

1.2 Manufacturer address 8

1.3 Customer service 8

1.4 Declarations of conformity 9

2 Safety

2.1 Intended use 13

2.1.1 Requirements for the operation 13

2.1.2 Pressure equipment directive 13

2.1.3 ATEX directive 13

2.1.4 Improper operating conditions 14

2.2 Modication 14

2.3 Structure of warning notices 14

2.3.1 Preceding warning notices 14

2.3.2 Integrated warning notices 14

2.3.3 Signal words 14

2.4 Personnel qualication 15

2.5 General safety instructions 15

2.5.1 General hazard16

2.5.2 Mechanical hazard16

2.5.3 Electrical hazard16

2.5.4 Thermal hazard16

2.6 Personal protective equipment 17

2.7 Safety devices 17

2.8 Residual hazards 17

2.9 Safety signs 19

2.10 Emergency measures 19

Table of Contents - 3 / 128

3 Description

3.1 Set-up and function 21

3.1.1 Design 21

3.1.2 Functional description 22

Spring-to-close actuator function (NC) 22

Spring-To-Open actuator function (NO) 23

Modifying the actuator closing direction 23

3.1.3 Signs 26

3.1.4 Protective devices 26

3.2 Technical data 27

3.2.1 Type plate 27

3.2.2 Technical data 27

3.2.3 Resistance and permitted operating temperature of the sealing mate-

rials 30

3.2.4 Pipe ends - General table of measurements 31

3.2.5 Lubricants 32

4 Storage and transport

4.1 Scope of supply 33

4.2 Storage 33

4.3 Transport 34

5 Assembly and installation

5.1 Notes on installation 35

5.2 Control top 35

5.3 Install the valve with detachable pipe connection elements 35

5.4 Install valve with welding ends 35

5.5 Checking the pneumatic connection 37

5.5.1 Air requirement 37

5.5.2 Establishing hose connections 37

5.5.3 Electrical connection with T.VIS control top 39

6 Commissioning

6.1 Preparing commissioning 41

6.2 Restarting 42

7 Operation and control

7.1 Start-up 43

7.2 Monitoring operation 43

7.3 Shutdown 43

8 Cleaning

8.1 General points 45

8.1.1 Cleaning process examples 45

8.1.2 Cleaning results 46

8.2 Passivation 46

4 / 128 - Table of Contents

0000000607 - 002 - EN-GB

9 Maintenance

9.1 Carrying out inspections 47

9.1.1 Checking seals that come into contact with the product 47

9.1.2 Checking the pneumatic connection 47

9.1.3 Checking the electrical connection 48

9.1.4 Checking the signs on the valve 48

9.2 Servicing intervals 48

9.3 List of tools 49

9.4 Prior to removal 50

9.5 Removing the valve 50

9.5.1 Removing the clamp connection between the upper and middle

housing 50

9.5.2 Disconnecting the valve insert from the housing 66

9.5.3 Dismantling the valve insert into individual parts 73

9.5.4 Dismantling of the housing combination 75

9.6 Installing the valve 75

9.6.1 Tightening torques 75

9.6.2 Assembling the valve insert from individual parts 76

9.6.3 Assembly of the housing combination 84

9.6.4 Placing the valve insert in the housing 84

9.6.5 Removing the clamp connection between the upper and middle

housing 88

9.6.6 Checking the function 99

9.7 Maintenance 100

9.7.1 Cleaning the valve 100

9.7.2 Replacing the V-ring 101

9.7.3 Lubricating seals and threads 104

10 Faults

11 Decommissioning, dismantling and disposal

11.1 Decommissioning 107

11.2 Dismantling 107

11.3 Disposal 107

12 Spare parts

12.1 Order information 109

12.2 Spare parts list 110

13 Annex

13.1 Dimension sheets 121

13.2 List of abbreviations 125

Table of Contents - 5 / 128

6 / 128 - Table of Contents

0000000607 - 002 - EN-GB

1 General

This chapter contains basic instructions for using the valve and explanations of illustra-

tion conventions. It also contains information about the design and structure.

The term valve in these Operating Instructions refers to GEA ECOVENT® Valve Type W_/

ECO.

1.1 Information about the document

1.1.1 Purpose and structure of the document

The objective of these Operating Instructions is to provide information on how to oper-

ate the valve. To achieve this, it is divided into several chapters which are oriented on

the various life phases of the valve. Compliance with the instructions will enhance the

valve's longevity and reliability, and reduce the likelihood of harm to individuals or dam-

age to property. The Operating Instructions also acts as the basis for creating operating

instructions.

1.1.2 Design elements

In this document, the following design elements are used as orientation aids.

General orientation aids

●Figure numbers

●Table numbers

●Chapter numbers

●Page numbers

●Headers and footers

●References

●Lists

Lists

Bullet points are shown in lists and do not prescribe a specic sequence.

●Bullet point

•Sub-point

●Bullet point

Numbered lists

In a sequence of actions, the order of the action steps is specied by a numbered list.

Partial results and the result of a sequence of actions are marked by arrows.

1. Action step one

2. Action step two

2.1 First sub-step two

2.2 Second sub-step two

®Partial result

3. Action step three

®Partial result

4. Action step four

ÞResult

1.1 Information about the document - 7 / 128

INFO

Info texts contain additional information about a description or action step.

1.1.3 Reading obligation and storage

Every person who works on or with the valve must have read these Operating Instruc-

tions. They must be available to these persons at all times.

1.2 Manufacturer address

GEA Tuchenhagen GmbH

Am Industriepark 2-10

Germany

21514 Büchen

1.3 Customer service

Phone: +49 4155 49-0

Fax: +49 4155 49-2035

[email protected]

www.gea.com

8 / 128 - 1.2 Manufacturer address

0000000607 - 002 - EN-GB

1.4 Declarations of conformity

1.4 Declarations of conformity - 9 / 128

Translated copy of the EU - Declaration of conformity in accordance with the

Pressure Equipment Directive 2006/42/EU

Manufacturer: GEA Tuchenhagen GmbH

Am Industriepark 2-10

21514 Büchen

We hereby declare that the machine named below

Designation: Valve with actuator

Type: ECOVENT®

on the basis of its design and construction, as well

as the version that we have put into circulation,

corresponds with the relevant fundamental health

and safety requirements of the following guide-

line:

Relevant EC directives: 2006/42/EC EC Machinery Directive

Applicable harmonized standards, in particular: EN ISO 12100: 2010

Remarks: ●This declaration will become invalid if any alter-

ations are made to the machine which have

not been agreed with us

●We also declare that the relevant technical

documentation for this machine has been pre-

pared in accordance with Annex VII, Part A,

and agree to submit the documentation on

justied request of national authorities on a

data carrier

Person authorised for compilation and handover

of technical documentation:

GEA Tuchenhagen GmbH

CE Documentation Ofcer

Am Industriepark 2-10

21514 Büchen, Germany

Büchen, 06 January 2021

Franz Bürmann

Managing Director

i.V

. Matthias Südel

Head of Engineering

10 / 128 - 1.4 Declarations of conformity

0000000607 - 002 - EN-GB

Inhaltsverzeichnis

Andere GEA Steuereinheit Handbücher

GEA

GEA VESTA XL Bedienungsanleitung

GEA

GEA VARIVENT A Kurzanleitung

GEA

GEA VARIVENT 24/7 PMO Bedienungsanleitung

GEA

GEA VARIVENT 24/7 PMO Bedienungsanleitung

GEA

GEA SVU 442 Bedienungsanleitung

GEA

GEA VESTA Bedienungsanleitung

GEA

GEA VARIVENT D Series Bedienungsanleitung

GEA

GEA VARIVENT N Bedienungsanleitung

GEA

GEA DHV Bedienungsanleitung

GEA

GEA Aseptomag ADV Bedienungsanleitung

GEA

GEA SIMATIC C7-623 Bedienungsanleitung

GEA

GEA HRAB Bedienungsanleitung

GEA

GEA VARIVENT T 09 Bedienungsanleitung

GEA

GEA VARIVENT T R Series Bedienungsanleitung

GEA

GEA 283 Bedienungsanleitung

GEA

GEA VARIVENT DN 25 Bedienungsanleitung

GEA

GEA DHV Bedienungsanleitung

GEA

GEA VARIVENT T R Series Bedienungsanleitung

GEA

GEA VARIVENT X R Series Bedienungsanleitung

GEA

GEA VARIVENT C Bedienungsanleitung

GEA

GEA VARIVENT T R Series Bedienungsanleitung

GEA

GEA VARIVENT FRS Bedienungsanleitung

GEA

GEA ECOspace Bedienungsanleitung

GEA

GEA H A/T Series Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung

Flyron

Flyron FN-BC04 Bedienungsanleitung