GEAppliances SIDE-BY-SIDE REFRIRATOR 22 Fehlerbehebungshandbuch

www.GEAppliances.com

Refrigerators

Top-Freezer

200D2463P007 49-60338 09-04 JR

Safety Instructions

Adapter Plugs . . . . . . . . . . . . . . . . . . . .3

Connect Electricity . . . . . . . . . . . . . . . .3

Extension Cords . . . . . . . . . . . . . . . . . .2

Proper Disposal . . . . . . . . . . . . . . . . . . .2

Safety Precautions . . . . . . . . . . . . . . . . .2

Operating Instructions

Additional Features . . . . . . . . . . . . . . . .9

Automatic Icemaker . . . . . . . . . . . . . .10

Controls . . . . . . . . . . . . . . . . . . . . . .4, 5

Crispers and Pans . . . . . . . . . . . . . .9, 10

Shelves and Bins . . . . . . . . . . . . . . . .7, 8

Water Dispenser . . . . . . . . . . . . . . . . .11

Water Filter . . . . . . . . . . . . . . . . . . . . . .6

Care and Cleaning . . . . . . . . . . . . . .11

Replacing the Light Bulbs . . . . . . . . .12

Installation Instructions

Preparing to Install

the Refrigerator . . . . . . . . . . . . . . . . . .13

Reversing the Door Swing . . . . . .18–22

Water Line Installation . . . . . . . . .14–18

Troubleshooting Tips . . . . . . . . .24–26

Normal Operating Sounds . . . . . . . . .23

Consumer Support

Consumer Support . . . . . . . .Back Cover

Performance Data Sheet . . . . . . . . . . .27

State of California Water

Treatment Device Certificate . . . . . . .28

Warranty for Canadian Customers . . .29

Warranty for U.S. Customers . . . . . . .30

Write the model and serial numbers here:

Model # __________________________

Serial # __________________________

Find these numbers on the gray label

on the left side, near the top of the

refrigerator compartment.

Réfrigérateurs

Congélateur supérieur

Manuel d’utilisation

et d’installation

La section française commence à la page 31

Refrigeradores

Congelador superior

Models 22, 25

Owner’s Manual &

Installation Instructions

Manual del propietario

e instalación

La sección en español empieza en la página 63

USE OF EXTENSION CORDS

Because of potential safety hazards under certain conditions, we strongly recommend against the

use of an extension cord.

However, if you must use an extension cord, it is absolutely necessary that it be a UL-listed (in the United

States) or a CSA-listed (in Canada), 3-wire grounding type appliance extension cord having a grounding

type plug and outlet and that the electrical rating of the cord be 15 amperes (minimum) and 120 volts.

DANGER! RISK OF CHILD ENTRAPMENT

Consumer Support Troubleshooting Tips Operating Instructions Safety InstructionsInstallation Instructions

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

WARNING!

Use this appliance only for its intended purpose as described in this Owner’s Manual.

SAFETY PRECAUTIONS

When using electrical appliances, basic safety precautions should be followed, including the following:

■

■This refrigerator must be properly installed

and located in accordance with the Installation

Instructions before it is used.

■

■Do not allow children to climb, stand or hang

on the shelves in the refrigerator. They could

damage the refrigerator and seriously injure

themselves.

■

■Do not touch the cold surfaces in the freezer

compartment when hands are damp or wet.

Skin may stick to these extremely cold surfaces.

■

■Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any

other appliance.

■

■In refrigerators with automatic icemakers,

avoid contact with the moving parts of the

ejector mechanism, or with the heating

element located on the bottom of the icemaker.

Do not place fingers or hands on the automatic

icemaking mechanism while the refrigerator

is plugged in.

■

■Keep fingers out of the “pinch point” areas;

clearances between the doors and between

the doors and cabinet are necessarily small.

Be careful closing doors when children are

in the area.

■

■Unplug the refrigerator before cleaning and

making repairs.

NOTE: We strongly recommend that any servicing be

performed by a qualified individual.

■

■Setting the controls to the O (off) position does

not remove power to the light circuit. On some

models, only the refrigerator control has a

O (off) setting.

■

■Do not refreeze frozen foods which have

thawed completely.

PROPER DISPOSAL OF THE REFRIGERATOR

Child entrapment and suffocation are not

problems of the past. Junked or abandoned

refrigerators are still dangerous…even if they

will sit for “just a few days.” If you are getting

rid of your old refrigerator, please follow the

instructions below to help prevent accidents.

Before You Throw Away Your Old

Refrigerator or Freezer:

■Take off the doors.

■Leave the shelves in place so that children

may not easily climb inside.

Refrigerants

All refrigeration products contain refrigerants,

which under federal law must be removed prior

to product disposal. If you are getting rid of an

old refrigeration product, check with the company

handling the disposal about what to do.

Consumer SupportTroubleshooting TipsOperating InstructionsSafety Instructions Installation Instructions

www.GEAppliances.com

WARNING!

HOW TO CONNECT ELECTRICITY

Do not, under any circumstances, cut or remove the third (ground) prong from the power cord. For

personal safety, this appliance must be properly grounded.

The power cord of this appliance is equipped

with a 3-prong (grounding) plug which mates

with a standard 3-prong (grounding) wall outlet

to minimize the possibility of electric shock hazard

from this appliance.

Have the wall outlet and circuit checked by

a qualified electrician to make sure the outlet

is properly grounded.

If the outlet is a standard 2-prong outlet,

it is your personal responsibility and obligation

to have it replaced with a properly grounded

3-prong wall outlet.

The refrigerator should always be plugged into

its own individual electrical outlet which has

a voltage rating that matches the rating plate.

This provides the best performance and also

prevents overloading house wiring circuits which

could cause a fire hazard from overheated wires.

Never unplug your refrigerator by pulling on the

power cord. Always grip plug firmly and pull

straight out from the outlet.

Repair or replace immediately all power cords

that have become frayed or otherwise damaged.

Do not use a cord that shows cracks or abrasion

damage along its length or at either end.

When moving the refrigerator away from the

wall, be careful not to roll over or damage the

power cord.

USE OF ADAPTER PLUGS (Adapter plugs not permitted in Canada)

Because of potential safety hazards under certain conditions, we strongly recommend against

the use of an adapter plug.

However, if you must use an adapter, where local

codes permit, a temporary connection may be made

to a properly grounded 2-prong wall outlet by use

of a UL-listed adapter available at most local

hardware stores.

The larger slot in the adapter must be aligned with

the larger slot in the wall outlet to provide proper

polarity in the connection of the power cord.

When disconnecting the power cord from the

adapter, always hold the adapter in place with one

hand while pulling the power cord plug with the

other hand. If this is not done, the adapter ground

terminal is very likely to break with repeated use.

If the adapter ground terminal breaks, DO NOT USE

the refrigerator until a proper ground has been

established.

Attaching the adapter ground terminal to a wall outlet

cover screw does not ground the appliance unless the

cover screw is metal, and not insulated, and the wall

outlet is grounded through the house wiring. You should

have the circuit checked by a qualified electrician to make

sure the outlet is properly grounded.

READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.

SAVE THESE INSTRUCTIONS

This feature allows you to lock the controls

so the settings cannot be changed.

To lock the controls:

Set the controls to the desired settings.

Press and hold the lock pad for

3 seconds.

When the controls are locked, the indicator

light will come on and the control settings

will not be displayed.

To unlock the controls:

Press and hold the lock pad for 3 seconds.

After unlocking the controls, the settings

will be displayed, the lock indicator light

will go out and the settings can be changed.

About the controls on the refrigerator.

The controls will look like one of the following:

Initially, set the refrigerator control at 5and the freezer control at 5

and allow 12–24 hours for the temperature to stabilize.

Several adjustments may be required. Adjust the controls one

increment at a time, and allow 12 hours after each adjustment for

the refrigerator to reach the temperature you have set.

Setting the controls to 0 stops cooling in both the refrigerator and

freezer compartments but does not shut off electrical power to

the refrigerator. On some models, only the refrigerator control has

a 0setting.

Touch pad controls

•Setting either control at 0will automatically set the other control at 0.

The zeros will blink until you set the controls.

•If both controls are set at 0and either COLDER pad is pressed, the

controls will automatically reset to 5.

Control settings will vary based on personal preferences, usage and

operating conditions and may require more than one adjustment.

Locking the Controls (on some models)

Troubleshooting Tips Operating Instructions Safety InstructionsInstallation Instructions

Troubleshooting Tips Installation Instructions Safety InstructionsOperating Instructions

Consumer Support

ADJUST REFRIGERATOR TEMP

ADJUST FREEZER TEMP ACTIVATE LOCK

IS COLDEST

9IS COLDEST

HOLD

3 SECS

COLDER WARMER COLDER WARMER

Consumer SupportTroubleshooting TipsOperating Instructions

Safety Instructions Installation Instructions

About the temperature controls. www.GEAppliances.com

The temperature controls are preset in the factory at 37°F for the

refrigerator compartment and 0°F for the freezer compartment.

Allow 24 hours for the temperature to stabilize to the preset

recommended settings.

The temperature controls can display both the SET temperature

as well as the actual temperature in the refrigerator and freezer.

The actual temperature may vary slightly from the SET

temperature based on usage and operating environment.

Setting either or both controls to OFF stops cooling in both the

freezer and refrigerator compartments, but does not shut off

electrical power to the refrigerator.

NOTE: The refrigerator is shipped with protective film covering

the temperature controls. If this film was not removed during

installation, remove it now.

To change the temperature, press and release the

WARMER or COLDER pad. The SET light will come

on and the display will show the set temperature.

To change the temperature, tap either the

WARMER or COLDER pad until the desired

temperature is displayed. Refrigerator temperatures

can be adjusted between 34°F and 44°F and the

freezer temperatures can be adjusted between

–6°F and +6°F.

Once the desired temperature has been set,

the temperature display will return to the actual

refrigerator and freezer temperatures after 5

seconds. Several adjustments may be required.

Each time you adjust controls, allow 24 hours for the

refrigerator to reach the temperature you have set.

To turn the cooling system off, tap the WARMER pad

for either the refrigerator or the freezer until the

display shows OFF. To turn the unit back on, press the

COLDER pad for either the refrigerator or freezer.

The SET light will illuminate on the side you

selected. Then press the COLDER pad again (on the

side where the SET light is illuminated) and it will

go to the preset points of 0°F for the freezer and

37°F for the refrigerator. Setting either or both

controls to OFF stops cooling in both the freezer

and refrigerator compartments, but does not shut

off electrical power to the refrigerator.

This feature allows you to lock the controls

so the settings cannot be changed.

To lock the controls:

Set the controls to the desired settings.

Press and hold the lock pad for

3 seconds.

When the controls are locked, the indicator

light will come on and the control settings

will not be displayed.

To unlock the controls:

Press and hold the lock pad for 3 seconds.

After unlocking the controls, the settings

will be displayed, the lock indicator light

will go out and the settings can be changed.

Locking the Controls (on some models)

Consumer Support Troubleshooting Tips Operating Instructions Safety InstructionsInstallation Instructions

Troubleshooting Tips Installation Instructions Safety InstructionsOperating Instructions

About the water filter. (on some models)

Water Filter Cartridge

The water filter cartridge is located inside

the cartridge holder in the back upper right

corner of the refrigerator compartment.

NOTE: Some models ship with the filter

bypass plug in place of the filter cartridge.

The filter bypass plug needs to be removed

before the filter cartridge is installed. Keep

the filter bypass plug for future use.

When to Replace the Filter

The filter cartridge should be replaced

every six months or earlier if the flow of

water to the icemaker and dispenser

decreases.

Installing the Filter Cartridge

If you are replacing the cartridge,

first remove the old one. To open the

cartridge cover, push in where indicated

and the cover will drop down.

Remove the cartridge by slowly rotating

it to the left. A small amount of water

may drip down.

CAUTION: If air has been

trapped in the system, the filter cartridge

may be ejected as it is removed. Use caution

when removing.

Mark your calendar to remind you to

replace the filter cartridge in six months.

Remove the protective foil from the end

of the cartridge.

Position the cartridge inside the

cartridge holder and slowly rotate the

cartridge to the right until it stops.

When the cartridge is properly installed,

you will feel it “click” as it locks into

place. The blade on the end of the

cartridge should be positioned

vertically. Do not overtighten.

Close the cartridge cover.

Run water from the dispenser for

3 minutes (about 11⁄2gallons) to clear

the system and prevent sputtering.

See To Use the Dispenser section.

NOTE: A newly-installed water filter cartridge

may cause water to spurt from the dispenser.

Filter Bypass Plug

You must use the filter bypass plug

when a replacement filter cartridge is not

available. The dispenser and the icemaker

will not operate without the filter or filter

bypass plug.

Replacement Filters

To order additional filter cartridges

in the United States, visit our Website,

www.GEAppliances.com, or call

GE Parts and Accessories, 800.626.2002.

Filter Model GSWF

Suggested Retail Price $34.95 USD

Customers in Canada should consult

the yellow pages for the nearest Camco

Service Center.

Consumer SupportTroubleshooting TipsOperating Instructions

Safety Instructions Installation Instructions

Rearranging the Shelves

To remove:

Tilt the shelf up at the front.

Lift the shelf up at the back and

bring the shelf out.

To replace:

While tilting the shelf up, insert the top

hook at the back of the shelf in a slot

on the track.

Lower the front of the shelf until the

bottom of the shelf locks into place.

Spillproof Shelves (on some models)

Spillproof shelves have special edges to

help prevent spills from dripping to lower

shelves. To remove or replace the shelves,

see Rearranging the Shelves.

About the shelves and bins. www.GEAppliances.com

Not all features are on all models.

Some models have wire shelves that

can be adjusted in the same manner.

To remove:

Lift up the left side of the shelf and

slide it left into the center of the shelf

supports.

Rotate the right side of the shelf up and

out of the shelf supports.

Shelves in the refrigerator and freezer compartments are adjustable.

Refrigerator Compartment

Freezer Compartment

To replace:

Holding the shelf diagonally, insert the

left end of the shelf into the center of

the shelf supports on the side wall at the

desired level.

Insert the right end of the shelf into the

shelf supports at the same level. Rest

each end of the shelf on the bottom of

the shelf supports.

NOTE: For models with an automatic icemaker,

the freezer shelf must be in the lower position

for the ice cube bucket to catch the cubes.

Consumer Support Troubleshooting Tips Operating Instructions Safety InstructionsInstallation Instructions

Troubleshooting Tips Installation Instructions Safety InstructionsOperating Instructions

About the shelves and bins (cont.).

Non-Adjustable Shelves on the Door

To remove: Lift the shelf straight up, then

pull out.

To replace: Engage the shelf in the molded

supports on the door and push down.

It will lock in place.

Adjustable Bins on the Door

Adjustable bins can easily be carried from

refrigerator to work area.

To remove: Lift bin straight up, then

pull out.

To replace or relocate: Engage the bin in the

molded supports of the door, and push in.

Bin will lock in place.

The snugger helps prevent tipping, spilling

or sliding of small items stored on the door

shelf. Grip the finger hold near the rear of

the snugger and move it to fit your needs.

Snugger

Freezer Tilt Out Bin (on some models)

Push the button as you tilt out the bin.

To remove: Hold the sides of the bin and

lift it straight up, then pull out.

To replace: Engage the ends of the bin in

the molded supports on the door and

push down. It will lock in place.

NOTE: Do not overload the bin.

Slide-Out Spillproof Shelf (on some models)

The slide-out spillproof shelf allows you

to reach items stored behind others. The

special edges are designed to help prevent

spills from dripping to lower shelves.

To remove:

Remove all items from shelf.

Slide the shelf out until it stops.

Lift the front edge of the shelf until the

central tabs are above the front bar.

Continue pulling the shelf forward

until it can be removed.

To replace:

Place the rear shelf tabs just in front of

the central notches on the shelf frame.

Slide the shelf in until the central tabs

are slightly behind the front bar.

Lower the shelf into place until it is

horizontal and slide the shelf in.

Make sure that the shelf sits flat after reinstallation

and doesn’t move freely from side to side.

Make sure you push the shelves all the way in

before you close the door.

Finger hold

Consumer SupportTroubleshooting TipsOperating Instructions

Safety Instructions Installation Instructions

About the crispers and pans.

Not all features are on all models.

About the additional features. www.GEAppliances.com

Not all features are on all models.

Fruit and Vegetable Crisper

Excess water that may accumulate in the

bottom of the drawers or under the drawers

should be wiped dry.

Adjustable Humidity Crisper (on some models)

Slide the control all the way to the

HIGH setting to provide high humidity

recommended for most vegetables.

Slide the control all the way to the LOW

setting to provide lower humidity levels

recommended for most fruits.

Shelf Saver Rack (on some models)

Slide-out beverage rack holds 12 cans of

soda or 2 wine/water bottles (lengthwise).

It can be removed for cleaning.

To remove, slide the rack out to the stop

position, lift the rack up and past the stop

position and lift it out.

Snack Pan (on some models)

This pan can be moved to the most useful

location for your family’s needs.

To remove, slide the pan out to the stop

position, lift the pan up and past the stop

position and lift it out.

Adjustable Temperature Deli Pan (on some models)

When the pan is placed in the top 6 slots

on the left side and the lever is set at

COLDEST, air from the freezer is forced

around the pan to keep it very cold.

You can move the pan to any location if

you don’t want the extra cold storage.

The settings can be adjusted anywhere

between cold and coldest .

When set at cold, the pan will stay at the

normal refrigerator temperature.

The coldest setting provides the coldest

storage area.

Consumer Support Troubleshooting Tips Operating Instructions Safety InstructionsInstallation Instructions

Troubleshooting Tips Installation Instructions Safety InstructionsOperating Instructions

About crisper removal.

Not all features are on all models.

About the automatic icemaker.

A newly-installed refrigerator may take 12–24 hours to begin making ice.

Crisper Removal

To Remove:

These drawers can be removed easily by

lifting up slightly while pulling the drawer

past the stop location.

When the door cannot be fully opened,

remove the drawer farthest from the door

first. Make sure the drawer closest to the

door is fully closed. There is a latch at the

front of the center slide rail. Push down on

the latch and slide the center slide rail, to

which the drawer is attached, away from the

door. Remove the drawer.

Icemaker Accessory Kit

If your refrigerator did not come already

equipped with an automatic icemaker,

an icemaker accessory kit is available at

extra cost.

Check the back of the refrigerator for

the specific icemaker kit needed for

your model.

Automatic Icemaker (on some models)

The icemaker will produce seven or eight

cubes (depending on model) per cycle—

approximately 100–130 cubes in a 24-hour

period, depending on freezer compartment

temperature, room temperature, number

of door openings and other use conditions.

There are two types of icemakers: power

switch models and feeler arm models.

If the refrigerator is operated before the

water connection is made to the icemaker,

set the power switch to O (off) or move the

feeler arm to the STOP (up) position.

When the refrigerator has been connected

to the water supply, set the power switch to

the I (on) position or move the feeler arm to

the ON (down) position. On power switch

models, the green light will come on.

You will hear a buzzing sound each time

the icemaker fills with water.

The icemaker will fill with water when it

cools to approximately 15°F. A newly-

installed refrigerator may take 12 to 24

hours to begin making ice cubes.

Throw away the first few batches of ice to

allow the water line to clear.

Be sure nothing interferes with the sweep

of the feeler arm.

When the bin fills to the level of the feeler

arm, the icemaker will stop producing ice.

It is normal for several cubes to be joined

together.

If ice is not used frequently, old ice cubes

will become cloudy, taste stale and shrink.

On power switch models, the green power

light will blink if ice cubes get stuck in the

icemaker. To correct this, set the power

switch to O (off) and remove the cubes. Set

the power switch to I (on) to restart the

icemaker. After the icemaker has been

turned on again, there will be a delay of

about 45 minutes before the icemaker

resumes operation.

NOTE: In homes with lower-than-average water

pressure, you may hear the icemaker cycle multiple

times when making one batch of ice.

Icemaker

Feeler Arm

Power

Switch

Green

Power Light

Power switch model

Feeler Arm in

the STOP

(up) position

Feeler Arm in

the ON (down)

position

Feeler arm model

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere GEAppliances Kühlschrank Handbücher

GEAppliances

GEAppliances PWE23 Betriebsanleitung

GEAppliances

GEAppliances PFE28P Betriebsanleitung

GEAppliances

GEAppliances Profile 20 Betriebsanleitung

GEAppliances

GEAppliances GMS10AAR Gebrauchsanweisung

GEAppliances

GEAppliances TFX22P Montageanleitung

GEAppliances

GEAppliances UseandCareGuide Bedienungsanleitung

GEAppliances

GEAppliances TCX22ZR Bedienungsanleitung

GEAppliances

GEAppliances GBS18HBP Gebrauchsanweisung

GEAppliances

GEAppliances GSH25SGP Gebrauchsanweisung

GEAppliances

GEAppliances GSE25HSHSS Sicherheitsleitfaden

GEAppliances

GEAppliances Profile 20 Betriebsanleitung

GEAppliances

GEAppliances GTH22SHR Gebrauchsanweisung

GEAppliances

GEAppliances Profile 20 Betriebsanleitung

GEAppliances

GEAppliances Spacemaker TAX4SNCWH–GE Gebrauchsanweisung

GEAppliances

GEAppliances PSB42 Betriebsanleitung

GEAppliances

GEAppliances TFX27N Montageanleitung

GEAppliances

GEAppliances TFX24RL Bedienungsanleitung

GEAppliances

GEAppliances GSS25LSM Gebrauchsanweisung

GEAppliances

GEAppliances GPE12 Betriebsanleitung

GEAppliances

GEAppliances GTE21 Betriebsanleitung

GEAppliances

GEAppliances GSS25SGM Gebrauchsanweisung

GEAppliances

GEAppliances MTR12 series Bedienungsanleitung

GEAppliances

GEAppliances GSS25JFM Gebrauchsanweisung

GEAppliances

GEAppliances GTL27 Betriebsanleitung

Beliebte Kühlschrank Handbücher anderer Marken

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Bedienungsanleitung

Sharp

Sharp SJ-BA31IEXW2-EU Bedienungsanleitung

CORBERO

CORBERO CC2300MCW Bedienungsanleitung

KitchenAid

KitchenAid 2205264 Bedienungsanleitung

Stengel

Stengel KU 1101 A++ Bedienungsanleitung

NEFF

NEFF KI181 Series Bedienungsanleitung

Hoshizaki

Hoshizaki Reach-In Bedienungsanleitung

Amana

Amana ASD2524VES00 Bedienungsanleitung

BOMANN

BOMANN KGC 213 Bedienungsanleitung

Danby

Danby DAR044A1SLDD Montageanleitung

Samsung

Samsung RF323TE Bedienungsanleitung

Beko

Beko CSA31022 Bedienungsanleitung

IKEA

IKEA FROSTIG C 185 E Bedienungsanleitung

Electrolux

Electrolux ER 6821 D Bedienungsanleitung

True

True TS-28 Bedienungsanleitung

Frigidaire

Frigidaire FSC23R5DW9 Bedienungsanleitung

Beko

Beko LSP4579W Bedienungsanleitung