Gecko in.ye-3-ce Technisches Handbuch
3- Select spa configuration (if prompt on startup)
3
At first startup the keypad display
will show Lx or LLx, where « x »
representing the config. number. Some
spa packs come with a pre-selected
config. and you may skip this step if
your system automatically starts up1.
1 Note: To re-enter the low level
selection menu, hold the Pump 1
key for 30 seconds.
Note: For the Color keypad series,
select Settings menu, go into
Electrical config and choose the
appropriate Low level.
2Note: If the keypad does not have a
Program or Filter key, use the Light
key instead.
Use the Up/Down key to choose the
new low level configuration number.
Press the Program2key to confirm the
selection.
21
1 phase connection
Phase jumpers Position
PJ1 P7-P13
PJ2 P10-P74
2 phase connection
Phase jumpers Position
PJ1 P7-P10
PJ2 P13-P74
3 phase connection (default)
Phase jumpers Position
PJ1 P7-P10
PJ2 P11-P13
3 phase Delta connection
Phase jumpers Position
PJ1 P7-P10
PJ2 P13-P74
2- Connect the main power
N N N
L3
L1 L1 L1
L2 L2
PJ1 PJ1 PJ1
PJ2 PJ2 PJ2
G G G
L3
L1
L2 PJ1
PJ2
G
Correct wiring of the electrical service
box, RCD, and pack terminal block is
essential. Power must be off during
this step.
input voltage: 230 V, 50 Hz (line-to-Neutral) input voltage: 230 V, 50 Hz (line-to-line)
WARNING! All connections must be made by a qualified electrician in accordance with the national electrical code and any
state, provincial or local electrical code in effect at the time of the installation. This product must always be connected to circuit
protected by a residual-current device (RCD).
Determine jumper positions for number of phases
4- Select breaker current
98
Press and hold the Program key for
20 seconds until you access the
breaker setting menu.
Note: For the Color keypad series,
select Settings menu, go into Electri-
cal config and choose Input current.
The values displayed by the system
correspond to the maximum
amperage capacity of the RCD.
Use the Up/Down key to select the
desired value. Then press the Program
key to confirm the selection.
Note: If the keypad does not have the
Program or Filter key, use the Light
key instead.
Current setting for each phase setting
# of phases Current setting range
110 to 48 A
210 to 20 A
310 to 16 A
Choose the number of phases
supplying your spa (1-3). Use the
Up/Down key to select the desired
value. Then press the Program key to
confirm the selection.
Specify the current rating and the number of phases of the RCD used to ensure safe and efficient current mangement (and no RCD trippings).
2 3 4
1
1- Connect all outputs & keypads
For more information, see our
website: www.geckoalliance.com
For more information, see our
website: www.geckoalliance.com
Quick Start Card
in.ye-3-ce™& in.ye-5-ce™European version
Light outputs
(P34 always on, P35 relay controlled)
Main power
entry connection
Heater connections
Bonding lugs
A1
A2
A3
A4
Heater
A4 Optional
connector
AMP ports
(A0 to A4) for pumps
& accessories.
Functions varie
per configuration
(see next page).
Optional floating
connector
(Part #9920-401346)
A0
H
H
L
L
G
G
C
C
A4
A3
A2
A1
C1 - Main keypad connector
CO - Communication links (2 ports)
in.touch, in.stik, Aux keypad in.k112,
Swim Spa com. cable, etc.
Standard config. # Pump 1 Pump 2 Pump 3 Blower Circ. Pump (CP)
configuration
Ozone (O3)
configuration1
Filter cycle
daily Heater pump
1
2SP
(A3)
10A-4A
_ _ _ _
During filter cycle with P1
(A1)
2 * 2 hour
with P1
with P1
12A
2
2SP
(A3)
10A-4A
1SP
(A1)
6A
_ _ _ _
2 * 2 hour
with P1
with P1
12A
3
2SP
(A3)
10A-4A
_ _
X
(A1)
4A
_ _
2 * 2 hour
with P1
with P1
12A
4
2SP
(A3)
10A-4A
_ _ _
During filter cycle
(A1 )
3A
_
2 * 6 hour
with CP
with CP
12A
5
1SP
(A3)
10A
_ _ _
During filter cycle
(A1 )
3A
During filter cycle with CP
(A2)
2 * 6 hour
with CP
with CP
12A
6
1SP
(A3)
10A
1SP
(A2)
6A
_ _
During filter cycle
(A1 )
3A
_
2 * 6 hour
with CP
with CP
12A
7
1SP
(A3)
10A
_ _
X
(A2)
4A
During filter cycle
(A1 )
3A
_
2 * 6 hour
with CP
with CP
12A
8
1SP
(A3)
10A
1SP
(A2)
6A
1SP
(A1)
12A
_
Always on
(A0)²
1A
_
2 * purge
CP always on
with CP
12A
9
1SP
(A3)
10A
1SP
(A2)
6A
_
X
(A1)
4A
Always on
(A0)²
1A
_
2 * purge
CP always on
with CP
12A
10
2SP
(A3)
10A-4A
1SP
(A1)
6A
_ _
Always on
(A0)²
1A
_
2 * purge
CP always on
with CP
12A
11
2SP
(A3)
10A-4A
_ _
X
(A1)
4A
Always on
(A0)²
1A
_
2 * purge
CP always on
with CP
12A
12
2SP
(A3)
10A-4A
1SP
(A1)
12A
_ _ _
2 * 2 hour
with P1
with P1
12A
13
1SP
(A3)
10A
1SP
(A1)
12A
_ _
During filter cycle
(A2)
3A
_
2 * 6 hour
with CP
with CP
12A
14
1SP
(A3)
10A
1SP
(A1)
12A
_
X
(A2)
4A
Always on
(A0)²
1A
_
2 * purge
CP always on
with CP
12A
15
2SP
(A3)
12A-4A
1SP
(A1)
12A
_ _
Always on
(A0)²
1A
_
2 * purge
CP always on
with CP
12A
16
2SP
(A3)
10A-4A
_ _ _
During filter cycle
(A1)
3A
_
2 * 2 hour
with P1
with CP
12A
Configuration selection chart
Software #382, rev. 003
For complete TechBook or more information, see our website: www.geckoalliance.com
9919-101496-C Rev. 11-2017 www.geckoalliance.com
© Groupe Gecko Alliance Inc., 2017
All trademarks or registered trademarks are the property of their respective owners.
1When the Ozonator is not controlled by a relay, it can be tied to Pump 1 Low speed or Circ. Pump. Pump using cable splitter AMP PN: 9920-401369.
2 A0 floating connector use Black: P28, White: Any available N connector, Green: Any available G connector. Floating connector not supplied. Part #9920-401346.
Glossary
(P1L) Pump 1 Low speed
(CP) Circulation Pump
XInstalled
1SP High speed only
2SP High and Low speed
(OUT, AMP, Relay, Tab) Output connector
13A-4A Current High - Low speed
Dieses Handbuch passt für folgende Modelle
1
Andere Gecko Industrieanlagen Handbücher
