Geeetech Me Creator Bedienungsanleitung

www.geeetech.com

Shenzhen Getech Technology CO.LTD

User Manual for Me Creator

www.geeetech.com

Shenzhen Getech Technology CO.LTD

1. Power Supply Wiring

1. Take out the power supply, there is a 110V/220V switch on it. Please make sure that the switch

is at the correct position according to the residential electricity standard of your country.

2. Loosen the screws, and connect power lines to corresponding ports in turn under the instructions

of the colors of power lines and the marks on DC power supply.

3. take note of the colors and their corresponding connection as a mistake can cause you harm or

damage the printer. If you are unsure of your skills and abilities here, please consult a

professional.

BROWN Live (L)

BLUE Neutral (N)

GREEN / Ground (GND)

YELLOW

RED Positive (+)

BLACK Common (COM)

www.geeetech.com

Shenzhen Getech Technology CO.LTD

Note: Both of the power supply and LCD of Me Creator are external, and there are no installation

holes set on the body of machine. Please find a flat place for the placement of your printer, LCD

and power supply.

2. Software Resources

2.1Repetier host V 1.6.0

http://www.repetier.com/download-now/

2.2Arduino IDE

http://www.geeetech.com/wiki/images/a/a2/Arduino-1.0.1-windows.zip

2.3Me Creator firmware（for Sanguinololu）

http://www.geeetech.com/forum/download/file.php?id=1563

3. Install USB Driver

Connect the printer to computer with USB cable, and the computer will start installing the

device driver software. After the successful installation of driver, please go to the Device

manager to find the USB Serial Port. This port is the printer's communications port.

If the driver can not be automatically installed, please download the USB driver and manually

install it.

http://www.ftdichip.com/Drivers/CDM/CDM%20v2.12.00%20WHQL%20Certified.exe

www.geeetech.com

Shenzhen Getech Technology CO.LTD

www.geeetech.com

Shenzhen Getech Technology CO.LTD

4. Connect the Printer to Repetier Host

After installing Repetier Host, plug USB cable into computer and open Repetier Host.

When you start Repetier Host for the first time, you need to configure the printer parameters,

and then do the connection. Click the Printer Settings in the top right corner,

following window will appear.

www.geeetech.com

Shenzhen Getech Technology CO.LTD

4.1 Create New Printer

In the pull-down menu at the top, it shows current selected printer. When it starts for the first

time, it only has the default printer. Change the name of the printer and click Apply can create a

new printer.

www.geeetech.com

Shenzhen Getech Technology CO.LTD

There are six tags in total here. Configure relevant parameters of the printer here.

4.2Connection

Choose right Port and Baud Rate. For other parameters please leave them as default, and click

Apply.

Port ：Get the printer connected to the port of computer, which is corresponding to the USB

Serial Port in the Device manager.

Baud Rate: Corresponding to the Baud Rate in firmware. Generally it is set as 250000.

www.geeetech.com

Shenzhen Getech Technology CO.LTD

Note: If the operating system is Mac OS, please set the baud rate as 115200. Meanwhile, you need

to do debugging for the motor direction of the printer again after re-uploading the firmware.

Open the firmware in Arduino 1.0.1, change the baud rate of firmware to 115200 in

Configuration.h file.

After modification, re-upload the firmware. About how to burn the firmware, please refer to the

FAQ.

www.geeetech.com

Shenzhen Getech Technology CO.LTD

After successfully modifying the baud rate in firmware, modify the baud rate in Repetier-Host

to 115200 as well.

www.geeetech.com

Shenzhen Getech Technology CO.LTD

4.3Printer

Set the extruder’s moving speed both in horizontal direction and Z-axis direction in the Printer tab,

and click Apply.

Travel Feed Rate: 4800mm/min

Z-Axis Feed Rate: 100mm/min

This is the default printing speed of Repetier-Host. You can adjust these two speeds if you need. But

please note that too fast print speed will lower the print quality.

Inhaltsverzeichnis

Andere Geeetech 3D-Drucker Handbücher

Geeetech

Geeetech A30 Bedienungsanleitung

Geeetech

Geeetech I3 Pro C Bedienungsanleitung

Geeetech

Geeetech Delta Rostock mini G2 Bedienungsanleitung

Geeetech

Geeetech GiantArm D200 Bedienungsanleitung

Geeetech

Geeetech Acrylic I3 Pro Betriebsanleitung

Geeetech

Geeetech A10 Bedienungsanleitung

Geeetech

Geeetech Mizar S Bedienungsanleitung

Geeetech

Geeetech A20M Bedienungsanleitung

Geeetech

Geeetech acrylic Prusa I3 Bedienungsanleitung

Geeetech

Geeetech Prusa I3 A pro Bedienungsanleitung

Geeetech

Geeetech A30 Pro Bedienungsanleitung

Geeetech

Geeetech Acrylic I3 Pro Betriebsanleitung

Geeetech

Geeetech Acrylic I3 Pro Bedienungsanleitung

Geeetech

Geeetech Duplicator 5 Bedienungsanleitung

Geeetech

Geeetech Acrylic I3 Pro Betriebsanleitung

Geeetech

Geeetech Prusa I3 X Bedienungsanleitung

Geeetech

Geeetech Rostock 301 Bedienungsanleitung

Geeetech

Geeetech A10M Bedienungsanleitung

Geeetech

Geeetech acrylic Prusa I3 Betriebsanleitung

Geeetech

Geeetech Aluminum Prusa I3 Bedienungsanleitung

Geeetech

Geeetech DP200 Bedienungsanleitung

Geeetech

Geeetech Rostock 301 Bedienungsanleitung

Geeetech

Geeetech Delta Rostock mini G2 Bedienungsanleitung

Geeetech

Geeetech Prusa I3 A pro Bedienungsanleitung

Beliebte 3D-Drucker Handbücher anderer Marken

Ultimaker

Ultimaker S5 Material Station Bedienungsanleitung

EcubMaker

EcubMaker TOYDIY Bedienungsanleitung

AnyCubic

AnyCubic Kossel Plus Bedienungsanleitung

ReDeTec

ReDeTec ProtoCycler Bedienungsanleitung

Kywoo3D

Kywoo3D Tycoon IDEX Bedienungsanleitung

CraftBot

CraftBot PLUS PRO Bedienungsanleitung

3DGence

3DGence INDUSTRY F340 Bedienungsanleitung

HP

HP Jet Fusion 4200 Betriebsanleitung

Rokit

Rokit AEP Series Bedienungsanleitung

AnkerMake

AnkerMake M5 Bedienungsanleitung

DIYElectronics

DIYElectronics PRUSA I3 Montageanleitung

Ackuretta

Ackuretta FreeShape 120 Bedienungsanleitung

LONGER

LONGER LK5Pro Bedienungsanleitung

Stratasys

Stratasys J850 Bedienungsanleitung

MakerBot

MakerBot Replicator Bedienungsanleitung

Stratasys

Stratasys FDM Vantage Series Bedienungsanleitung

ZYYX

ZYYX Pro II Bedienungsanleitung

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Benutzerhandbuch