Gefen ETH-2-PLC Bedienungsanleitung
Ethernet Over PLC
User Manual
www.gefentv.com
GTV-ETH-2-PLC
Technical Support:
Telephone (818) 772-9100
(800) 545-6900
Fax (818) 772-9120
Technical Support Hours:
8:00 AM to 5:00 PM Monday thru Friday.
Write To:
Gefen Inc.
c/o Customer Service
20600 Nordhoff St
Chatsworth, CA 91311
www.gefentv.com
support@gefentv.com
Notice
Gefen Inc. reserves the right to make changes in the hardware, packaging and
any accompanying documentation without prior written notice.
GefenTV Ethernet Over PLC is a trademark of Gefen Inc.
© 2008 Gefen Inc., All Rights Reserved
All trademarks are the property of their respective companies
ASKING FOR ASSISTANCE
CONTENTS
1 Introduction
2 Operation Notes
3 Features
4 Sender Panel Layout
5 Sender Panel Descriptions
6 Receiver Panel Layout
7 Receiver Panel Descriptions
8 GefenTV Ethernet Over PLC Software Installation
11 Connecting The GefenTV Ethernet Over PLC
17 Automatic Security Setup Feature
19 Advanced Configuration
24 Web Configuration
27 Firmware Update Procedure
28 Specifications
29 Warranty
Congratulations on your purchase of the GefenTV Ethernet Over PLC. Your
complete satisfaction is very important to us.
Gefen TV
Gefen TV is a unique product line catering to the growing needs for innovative
home theater solutions. We specialize in total integration for your home theater,
while also focusing on going above and beyond customer expectations to ensure
you get the most from your hardware. We invite you to explore our distinct
product line and hope you find your solutions. Don’t see what you are looking for
here? Please call us so we can better assist you with your particular needs.
The Gefen Ethernet Over PLC
Send RJ-45 Ethernet signals over power lines in the walls of your home with the
GefenTV Ethernet Over Power Line Bridge. The Bridge’s sender and receiver
units send Ethernet through the walls of a building at a distance of up to 1000
feet.
Ideal for tough installations where running CAT5/CAT6 cable is not possible,
these devices breathe new life into remote network extensions.
How It Works
Connect your Ethernet network cables to the GefenTV Ethernet Over Power Line
Bridge Sender unit, then plug the Bridge’s Sender into a nearby power outlet.
At the desired reception area in another room, plug the Bridge’s Receiver into
a power outlet. Power cycle your equipment and you will now receive network
signals at your remote destination as if you had cabled the run with Ethernet
cables.
1
INTRODUCTION
READ THESE NOTES BEFORE INSTALLING OR
OPERATING THE GEFENTV ETHERNET OVER PLC
This device passes all 10/100BASE-T Ethernet network protocols (TCP/• IP, NETBUEI, Microsoft Networking, etc.) at speeds of up to 200Mbps (Full
duplex fast Ethernet).
All devices connected to the sending and receiving nodes must be on the• same power phase to communicate properly.
Multiple receiving nodes can be used on the same in-house power line• system to extend the network to multiple locations.
Performance of• GefenTV Ethernet Over PLC can be affected by “noisy”
devices on the power lines. This can be alleviated by using a PLC filter
(Part# GTV-PLC-FUS for US and GTV-PLC-FEU for Europe). Offending
devices need to be connected to the PLC filter before being connected to the
wall outlet.
2
OPERATION NOTES
3
Features
Supports up to 200 Mbps data transmission rate•
Extension of up to 200 feet (60 meters)•
Web configuration for easy maintenance•
Features include IGMP multicast, VLAN, and QOS packet management•
3DES 168 bits encryption used for secure operation•
Four RJ-45 Ethernet ports•
Package Includes
(1) GefenTV Ethernet Over PLC sender
(1) GefenTV Ethernet Over PLC receiver
(1) 3 foot Ethernet Patch Cable
(2) Power Adapter Cables
FEATURES
4
Front Panel
Back Panel
Top Panel
1
4
23
Top Panel
p
5
6
7
SENDER PANEL LAYOUT
5
SENDER PANEL DESCRIPTIONS
Standby Button1.
Pressing this will put the sending unit in standby mode. The unit will not
transfer any information to the receiving unit in this mode. To release
standby mode, simply press the button again.
Ethernet Input Port2.
Connects to the Ethernet source (i.e a router, computer, or Internet
connection) via a standard network cable.
Security/Reset Button3.
Pressing this button for 2 seconds will activate the Automatic Security
Configuration (please see page 17). Pressing this button for more than 10
seconds will perform a factory reset.
AC Power Cable Input4.
Input for the supplied AC power cable.
LAN LED5.
This LED will activate when a connection to a valid Ethernet source is
established. It will blink when activity is detected to signify that data is
actively being trafficked to and from the receiver.
Link LED6.
This LED will activate once a link has been established between the sending
and receiving units. It will blink when activity is detected to signify that data is
actively being trafficked.
Power LED7.
This LED will activate once the included power supply is properly connected.
6
Front Panel
Back Panel
Top Panel
1
4
23
Top Panel
p
5
7
7
8
9
10
RECEIVER PANEL LAYOUT
7
RECEIVER PANEL DESCRIPTIONS
Standby Button1.
Pressing this will put the receiving unit in standby mode. The unit will not
transfer any information to the sending unit in this mode. To release standby
mode, simply press the button again.
Ethernet Input Port ( 1 through 4)2.
Connects to an Ethernet device (i.e a computer or gaming system) via a
standard network cable. 4 ports are available for 4 separate devices.
Security/Reset Button3.
Pressing this button for 2 seconds will activate the Automatic Security
Configuration (please see page 17). Pressing this button for more than 10
seconds will perform a factory reset.
AC Power Cable Input4.
Input for the supplied AC power cable.
LAN 1 LED5.
This LED will activate when a connection from a valid Ethernet device to
Ethernet port 1 is established. It will blink when activity is detected to signify
that data is actively being trafficked to and from this port.
LAN 2 LED6.
This LED will activate when a connection from a valid Ethernet device to
Ethernet port 2 is established. It will blink when activity is detected to signify
that data is actively being trafficked to and from this port.
LAN 3 LED7.
This LED will activate when a connection from a valid Ethernet device to
Ethernet port 3 is established. It will blink when activity is detected to signify
that data is actively being trafficked to and from this port.
LAN 4 LED8.
This LED will activate when a connection from a valid Ethernet device to
Ethernet port 4 is established. It will blink when activity is detected to signify
that data is actively being trafficked to and from this port.
Link LED9.
This LED will activate once a link has been established between the sending
and receiving units. It will blink when activity is detected to signify that data is
actively being trafficked to and from the sender.
Power LED10.
This LED will activate once the included power supply is properly connected.
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Gefen Extender Handbücher
Gefen
Gefen EXT-VGA-141LR Bedienungsanleitung
Gefen
Gefen ex-tend-it CAT5-1000 Bedienungsanleitung
Gefen
Gefen CAT5-7500 Bedienungsanleitung
Gefen
Gefen RS-232 Bedienungsanleitung
Gefen
Gefen HDTV-CAT5 Bedienungsanleitung
Gefen
Gefen GTV-WHD-60G Bedienungsanleitung
Gefen
Gefen DVI CAT-5 Extreme Bedienungsanleitung
Gefen
Gefen DVI-FMP Bedienungsanleitung
Gefen
Gefen RS-232 Bedienungsanleitung
Gefen
Gefen HDMI-1000HD Bedienungsanleitung
Gefen
Gefen ADC-141 Bedienungsanleitung
Gefen
Gefen EXT-DVI-CAT5-4X Bedienungsanleitung
Gefen
Gefen EXT-USB-MINI2N Bedienungsanleitung
Gefen
Gefen GTV-WVGA-LR Bedienungsanleitung
Gefen
Gefen DVIRS232-CAT5 Bedienungsanleitung
Gefen
Gefen Pro DVI FM 2000 Bedienungsanleitung
Gefen
Gefen EXT-COMPAUD-CAT5-142 Bedienungsanleitung
Gefen
Gefen EXT-UHDV-KA-LANS-TX Bedienungsanleitung
Gefen
Gefen HDMI-CAT5-4X Bedienungsanleitung
Gefen
Gefen DVI-1000HD Bedienungsanleitung
