Gemini 972AR Leitfaden

Made in Italy AC 2791/UK Rev. 01 - 11/10

972AR

GEMINI Technologies S.p.A.

Via Luigi Galvani 12 - 21020 Bodio Lomnago (VA) - Italia

Tel. +39 0332 943211 - Fax +39 0332 948080

Web site: www.gemini-alarm.com

Reg. n.532-A

UNI EN ISO 9001:2008

INSTALLATION CERTIFICATE

The undersigned qualified installer attests having personally fitted the alarm system on the vehicle

specified below, following the manufacturer’s instructions.

................................................

..........................................................................................................................

By :

Sold on : :Type of device

Vehicle :

972

INSTALLATION AND USE

MANUAL

1.0

2.0

3.0

4.0

5.0

6.0

7.0

8.0

9.0

10.0

- PRELIMINARY ADVICE.............................................................................................

- TECHNICAL DATA...................................................................................................

- OPERATING DESCRIPTION.....................................................................................

3.1 - System arming..........................................................................................................

3.2 - Arming inhibit time....................................................................................................

3.3 - System armed..........................................................................................................

3.4 - Alarm, inhibit time between alarms and alarm cycles..............................................

3.5 - System disarming.....................................................................................................

- GARAGE FUNCTION................................................................................................

- ANTI-HIJACK FEATURE............................................................................................

.........................................................................

......................................................................

5.3 - ......................................................................

5.4 - Deactivation of anti-hijack feature............................................................................

- TAG CARD ACTIVATION AND BATTERY REPLACEMENT.......................................

- WARRANTY CONDITIONS........................................................................................

- CONNECTOR TABLE.................................................................................................

- COMPLETE ELECTRIC DIAGRAM...........................................................................

- .........................................................

..............................................................

WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT (WEE) DIRECTIVE........

USER MANUAL

INSTALLER MANUAL

5.1 - Vehicle running: normal functioning

5.2 - Vehicle running: agression and hijack

Vehicle running: anti-hijack activation

ADDING NEW DEVICES.................................

- DELETING OF PROGRAMMED DEVICES

11.0

12.0

PAGE 02

1.0 - PRELIMINARY ADVICE

Dear customer,

The following signs are intended to draw user and installer attention to particular functions or

connections as follows:

USER MANUAL - PAGE 03

PAGE 02

PAGE 03

PAGE 04

PAGE 05

PAGE 06

PAGE 07

PAGE 08

PAGE 09

PAGE 05

Indications useful for the user.

This icon provides the user with indications for a diversificated use of the system or it

simply provides indications useful for the use.

Indications useful for the installer.

This icon indicates to the installer a diversificated operating, according to the connection

and the programming of the system or it simply provides indications useful for the

installation.

TABLE OF CONTENTS

2.0 - TECHNICAL DATA

Operating power

Current absorption @ 12Vdc with system armed and LED flashing

Operating temperature range

Turn signals relay contact capabilty

Engine immobilisation relay contact capability

Alarm cycle

Horn output current capacity

12 Vdc

Less than 15 mA

From -30°C to +70°C

8 A to 20°C

30 sec.

USER MANUAL

3.1 - SYSTEM ARMING

3.2 - ARMING INHIBIT TIME

3.3 - SYSTEM ARMED

3.4 - ALARM, INHIBIT TIME BETWEEN ALARMS AND ALARM CYCLES

3.5 - SYSTEM DISARMING

The system arms automatically 30” after turning off the engine (lack of ignition key contact) as long as

no TAG transmission is detected.

Opening a door 30” before the system is armed temporarily interrupts the procedure which will resume

once the door is closed.

The inhibit arming time lasts for approxiately 8” and is indicated by the status LED turning ON steady;

during this period it’s possible to exit the vehicle without triggering any alarm.

After the inhibit time the system is “armed” and it is ready to detect any theft attempt.

When the system fully armed, the LED flashes.

Before any audio/visual signalling of the alarm occurs there is a 16” pre-alarm neutral time (LED

steady ON).

The system indicates theft attempts by visual/audio signals (flashing of the turn indicators and

intermittent sounding of the vehicle horn).

After the alarm event, but before another alarm is triggered, there is a 5” neutral time.

The alarm signalling has 5 cycles of 30” each for each input and for each arming cycle.

If the system is armed, it will start disarming upon detecting your TAG; the disarming procedure will

then be completed when the driver door is opened.

4.0 - GARAGE FUNCTION

This garage feature “deactivates” the system and is useful wnen the vehicle is in a

workshop for maintenance or repais or if the TAG CARD is not working

When the “garage feature” is ON, the status LED blinks twice followed by a 2 seconds

pause.

The garage feature can be activated with system armed or disarmed

System deactivation is indicated by three acoustic signals of the buzzer.

System activation is indicated by an acoustic signal of the buzzer.

by inserting the electronic key in

its receptacle while the driver door is opened

To reactivate the system simply introduce the electronic key in its receptacle

To activate the garage feature during an alarm condition or during a hijack attempt (vehicle running)

simply introduce the electronic key in its receptacle (door either opened or closed).

3.0 - OPERATING DESCRIPTION

PAGE 04 - USER MANUAL USER MANUAL - PAGE 05

6.0 - TAG CARD ACTIVATION AND BATTERY REPLACEMENT

To activate the TAG CARD simply press the button and keep it pressed for at least 4 seconds.

The LED turns on steady when the TAG is activated and it will flash each time the TAG transmits.

If not moved for 10 min., the TAG will automatically go into standby to save battery life; to’ wake it up’ for

another transmission cycle (10 min.), move it or press the button

Another short button press will send a radio signal to the alarm system.

To turn the TAG off, press the button and keep it pressed for at least 8 seconds.

The LED stays on steady and after 8 seconds it will flash briefly to indicate the TAG is switched off.

To replace battery proceed as follows

7.0 - WARRANTY CONDITIONS

This product is garanteed to be free from defects in workmanship for a period of 24 months from the

date of installation reported on this warranty, in compliance with the 1999/44/CE Warranty Directive

(L.D. N° 24 of the 02/02/2002).

Please fill-in entirely the guarantee certificate included in this booklet and DO NOT REMOVE the

guarantee label from the device.

The warranty will become void if labels are misssing or torn, if the installation certificate is not fully

compiled or if the enclosed sale document is missing.

The warranty is valid exclusively atAuthorized Gemini Centers.

The manufactuer declines any responsability for eventual malfunctions of the device or any damage

to the vehicle electrical system due to improper installation, use or tampering.

This alarm is solely intended to be a theft-deterrent device.

Separate the plastic

covers and remove the

circuit with care.

Slide out dead battery

and insert new one.

Pay attention not to

invert polarity.

Reassemble the covers, turn

on the TAG and make sure it

works.

For security reasons, we recommend you keep your electronic key and TAG separate

from your ignition key so that, if your vehicle is robbed, you have your electronic key

and TAG with you.

Arming the anti-hijack feature means that only TAG reception and identification is

activated and not vehicle immobilization.

5.0 - ANTI-HIJACK FEATURE

The 972AR module has an anti-hijack feature for protection against aggression or vehicle theft.

It operates by means of an automatic transmitter (TAG), which comunicates with the 972AR module

via a codified radio signal.

the alarm system activates the anti-

hijack procedure, .

When ignition is turned OFF, the module arms and works as an alarm and the TAG as a remote control.

When the vehicle is running and there is no TAG transmission,

as described further on

This feature can be activated even if the vehicle is turned OFF;

Under this condition, the system only detects .

As already mentioned, in case of car theft, the user should still have his TAG with him.

To deactivate the anti-hijack feature all the driver has to do is walk up to his vehicle with the TAG.

The module, on intercepting the signal, will deactivate the anti-hijack feature and stop the optic and

acousic alarm signals.

Deactivation of the anti-hijack feature with electronic key will arm the “garage function” (see par. 4.0).

5.1 - VEHICLE : NORMAL OPERATION

5.2 - VEHICLE RUNNING: AGGRESSION AND HIJACKING

5.3 - VEHICLE RUNNING: ANTI-HIJACK ACTIVATION

5.4 - DEACTIVATION OF ANTI-HIJACK FEATURE

if it is turned ON and the system does

not detect the TAG, the anti-hijack feature arms

TAG transmission and the LED does not blink

If the door is

opened and the driver walks away with theTAG, the module no longer detects radio contact and

enters, after 60”, in pre-arm mode

The turn indicators and the buzzer, siren or the horn (if connected) will activate for 2 minutes

20” after the audio/visual signals, the vehicle immobilizer will activate (20” ON/OFF up to a complete

stop)

If the driver doesn’t turn them off, the turn indicators will keep flashing for 3 hours while the siren or

horn will sound for two minutes

RUNNING

Figure 1 Figure 2

Figure 3

Use ONLY CR2032 type battery; do not discard used batteries in trash but safely

dispose in appropriate containers.

8.0 - CONNECTOR TABLE

Negative input for new devices programming

Doors push-button negative input

Positive under key

-------

Ground

Horn negative output

Buzzer negative output

Ground for LED and receptacle for electronic key

LED positive output

Positive

Antenna

Input receptacle for electronic key

Engine Immobilization

urn indicators output

Turn indicators output

Turn indicators output common

-------

-1-

-2-

-3-

-4-

-5-

-6-

-7-

-8-

-9-

-10-

-11-

-12-

-13-

-14-

-15-

-16-

-17-

-18-

-19-

-20-

-21-

-22-

-23-

-24-

GREEN

GREEN-BROWN

BLACK marked “G”

-------

BLACK marked “M”

YELLOW-BLACK

GREEN-RED

BLACK and BROWN

RED

BLACK marked “R”

BLACK

GREEN

BLACK marked “H”

ORANGE

WHITE-RED

-------

WIRE FUNCTIONPOSITION WIRE COLOR

15A +

Battery

10A

MAX !

BLACK marked “M”

GROUND

POSITIVE

BLACK marked “R”

It is reccomended to use a 10A fuse

YELLOW-BLACK

WHITE-RED

Horn

(negative output in alarm)

ORANGE

Turn signals relay common

Turn signals output

BLACK marked “G”

+30

Positive under key

BLACK marked “H”

GREEN-REDRED

BLACK

Engine immobilizer

Buzzer

Antenna, do not tamper

Doors push-button input

Negative input for

new devices programming

Buzzer positive

output

BLACK

GREEN-BROWN

GREEN

9.0 - COMPLETE ELECTRIC DIAGRAM

Before carrying out all

electrical connections,

disconnect the negative

battery terminal and re-

connect again after

completion.

PAGE 06 - INSTALLER MANUAL INSTALLER MANUAL - PAGE 07

INSTALLER MANUAL

ELECTRONIC KEY

To activate the anti-carjack feature, the positive under key (BLACK wire marked “G”)

and the GREEN-BROWN) MUST be connected.door push-button (

We recommend you ALWAYS make these connections.

Red

Black

Green

Brown

PAGE 08 - INSTALLER MANUAL INSTALLER MANUAL - PAGE 09

11.0 - DELETING PROGRAMMED DEVICES

The system has a delete mode to remove a programmed electronic key or TAG CARD.

o activate the procedure follow the indications reported belowT.

With the alarm system disarmed, open and keep opened the driver door and connect to ground the

GREEN wire.

Close the door; the LED turns on steady.

Turn ignition key over 4 times: “ON-OFF”-“ON-OFF”-“ON-OFF”-“ON”

At the fourth rotation, keep ignition key “ON”

The buzzer will chirp twice and the turn indicators will flash twice to indicate that the delete

procedure has been initiated.

Keep the bonnet closed for at least 8 seconds until all the devices are cancelled

The following operations must be carried out within four seconds otherwise the

procedure is invalidated.

!When this procedure is completed, the LED turns off, the buzzer chirps once and the turn indicators

flash once.

Turn ignition key to “OFF” and disconnect from gronud the GREEN wire!.

10.0 - ADDING NEW DEVICES

To carry out this operation successfully, you must first make the required electrical

connections (door switch, GREEN wire to ground and and positive under key).

To carry out this operation successfully, you must first make the required electrical

connections (door switch, GREEN wire to ground and and positive under key).

! !

The system can

With the alarm system disarmed, open and keep opened the driver door and connect to ground the

GREEN wire.

record a maximum of 11 devices, either electronic keys or TAG CARDS.

To activate the procedure follow the indications reported below.

Turn ignition key over 4 times: “ON-OFF”-“ON-OFF”-“ON-OFF”-“ON”.

At the fourth rotation, keep ignition key “ON”

The buzzer will chirp twice and the turn indicators will flash twice to indicate the learning procedure

of new devices has started

The following operations must be carried out within four seconds otherwise the

procedure is invalidated.

Do not close the driver door otherwise the devices already saved will be deleted as

described in the next paragraph

Storing memory is for 11 devices. If you store an extra one it will automatically delete

the first device recorded in the system memory.

Repeat other devices.

Turn ignition key to “OFF”, close the door and remove from ground the GREEN wire

The system is now ready to receive the device codes

Depending on the device to be recorded, either insert the electronic key into its receptacle or let the

system pick up the TAG signal

To indicate the new device is learned, the buzzer chirps once and the status LED blinks once

the above steps to record

When the procedure is completed, the siren buzzer once

The devices will not be deleted if the door is opened before 8 seconds.

APPROPRIATE

CONTAINER ONLY

12.0 - WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT

(WEEE) DIRECTIVE

In the European Union, this lable indicated that this product should not be disposed of with household

waste. It should be deposited at an appropriate facility to enable recovery and recycling (directive

2002/95/CE, 2002/96/CE and 2003/108/CE).

For information on how to recycle this product responsibly in your Country, please visit the web-site:

www.eur-lex.europa.eu

Andere Gemini Steuereinheit Handbücher

Gemini

Gemini 4100 Bedienungsanleitung

Beliebte Steuereinheit Handbücher anderer Marken

Festo

Festo Compact Performance CP-FB6-E Stücklistenhandbuch

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung

JS Automation

JS Automation MPC3034A Bedienungsanleitung

JAUDT

JAUDT SW GII 6406 Series Kurzanleitung

Spektrum

Spektrum Air Module System Bedienungsanleitung

BOC Edwards

BOC Edwards Q Series Bedienungsanleitung

KHADAS

KHADAS BT Magic Bedienungsanleitung

Etherma

Etherma eNEXHO-IL Bedienungsanleitung

PMFoundations

PMFoundations Attenuverter Bedienungsanleitung

GEA

GEA VARIVENT Bedienungsanleitung

Walther Systemtechnik

Walther Systemtechnik VMS-05 Bedienungsanleitung

Altronix

Altronix LINQ8PD Montageanleitung

Eaton

Eaton Powerware Series Bedienungsanleitung

WAGO

WAGO 750-407/040-000 Bedienungsanleitung

Sony

Sony CCU-590 Bedienungsanleitung

Graco

Graco 25D614 Bedienungsanleitung

Task Force Tips

Task Force Tips YE-RF-900 Programmierhandbuch

Shini

Shini SPV-U Series Bedienungsanleitung