Gemotech RemoDAQ-8000 Series Bedienungsanleitung
V1.1 2010.2.2
RemoDAQ-8054
User’s Manual
Beijing Gemotech Intelligent Technology Co.，Ltd
RemoDAQ-8054 User’s Manual
Copyright Notice
This document is copyrighted, 2005, by Beijing
Gemotech Intelligent Technology Co.，Ltd
All rights are reserved. Beijing Gemotech Intelligent
Technology Co. ，Ltd reserves the right to make
improvements to the products described in this manual at any
time without notice.
No part of this manual may be reproduced, copied,
translated or transmitted in any form or by any means without
the prior written permission of Beijing Gemotech Intelligent
Technology Co.，Ltd. Information provided in this manual is
intended to be accurate and reliable. However, Beijing
Gemotech Intelligent Technology Co.，Ltd assumes no
responsibility for its use, or for any infringements upon the
rights of third parties, which may result from its use.
Acknowledgments
RemoDAQ is a trademark of Beijing Gemotech
Intelligent Technology Co.，Ltd.
Edition 1.1
Feb. 2009
1
RemoDAQ-8054 User’s Manual
Additional Information and Assistance
1. Visit the gemotech websites at www. gemotech. cn
where you can find the latest information about the product.
2. Contact your distributor, sales representative, or
gemotech 's customer service center for technical support if
you need additional assistance. Please have the following
information ready before you call：
zProduct name and serial number
zDescription of your peripheral attachments
zDescription of your software (operating system,
version，application software, etc.)
zA complete description of the problem
zThe exact wording of any error messages
2
RemoDAQ-8054 User’s Manual
Table of Contents
..............................................................................................41 Introduction
..............................................41.1 PinAssignment & Specifications
...........................................................................51.2 Block Diagram
....................................................................51.3 Application Wiring
...........................................................................61.4 Default Setting
1.5 Jumper Setting............................................................................6
..................................................................................61.6 Install List
......................................................................72 Initialization & Installation
.................................................................72.1 Installation Guideline
..................................................................72.2 Software Installation
...............................................82.3 Basic configuration and hook-up
..........................................................102.4 Baudrate and Checksum
.........................................................................................123 Command Set
....................................................................153.1 %AANNTTCCFF
........................................................................................173.2 $AA2
........................................................................................183.3 $AA6
........................................................................................193.4 $AAF
......................................................................................203.5 $AAM
........................................................................................213.6 @AA
3.7 ~AAO(Data).............................................................................22
3
RemoDAQ-8054 User’s Manual
1 Introduction
The RemoDAQ-8000 Series is a set of intelligent sensor to
computer interface modules containing built in microproces-
sor. They are remotely controlled through a simple set of
commands issued in ASCII format and transmitted in RS-485
protocol. They provide signal conditioning, isolation, ranging,
A/D and D/A conversion, data comparison, digital commun-
ication, timer/counter, wireless communication, collection
AC and other functions.
RemoDAQ-8054 is the 8-channel cable ON/OFF detecti-
on module that are used in telecommunications profession
specially, LED shows the ON/OFF state of 8-channel cable,
each channel has a LED state of instructing this road. When
cable shorts , LED OFF;When cable broken road, LED ON.
Its power supply also with other module is difference, for
44~58Vdc.
1.1 Pin Assignment & Specifications
Channel：8
Power：44V~58VDC
Power consumption：1.6W
Operating Temperature：-20 ~ 70° C
Humidity：5 ~ 95%, non-condensing
4
RemoDAQ-8054 User’s Manual
1.2 Block Diagram
1.3 Application Wiring
Dry Contact Input
5
RemoDAQ-8054 User’s Manual
1.4 Default Setting
zAddress：01
zBaudrate：9600 bps
zType：40
zChecksum disable
zJP1 disconnection：disconnection INIT* pin with the
GND pin，natural work mode
1.5 Jumper Setting
JP1：Select INIT* pin with the GND pin whether connect
Disconnection：Don’t connect INIT* pin with the GND pin
Connection：Connect INIT* pin with the GND pin
1.6 Install List
Baudrate Setting (CC)
Code 03 04 05 06 07 08
Baudrate 1200 2400 4800 9600 19200 38400
Type Setting (TT)
Type=40
Data format setting（FF）
7 6 5 4 3 2 1 0
0 *1 0
*
1：Checksum：0=Disabled 1=Enable
Read DIO data format
$AA6：（Data1）（Data2）
@AA Data：（Data1）（Data2）
Data1 Data2
RemoDAQ-8054 DI(0-7) 00 ~ FF 00 00
6
RemoDAQ-8054 User’s Manual
2 Initialization & Installation
2.1 Installation Guideline
Figure 2-1 Power Supply Connections
We advise that the following standard colors (as indicated
on the modules) be used for power lines：
+Vs (R) Red
GND (B) Black
We advice that the following standard colors (as indicated
on the modules) be used for the communication lines：
DATA+ (Y) Yellow
DATA- (G) Green
2.2 Software Installation
1. If you have already installed “RemoDAQ-8000 Utility”
then skip other steps.
2. Backup your software diskette.
3. Insert “RemoDAQ-8000 Utility” disc into CD-ROM：
4. Change drive to the path of CD-ROM. For example,
7
RemoDAQ-8054 User’s Manual
your drive of CD-ROM is F：then change the drive to F：
5. Find the setup of “RemoDAQ-8000 Utility” and run it.
6. Please follow the steps of setup program then you can
successfully install the RemoDAQ-8000 Utility
2.3 Basic configuration and hook-up
Before placing a module in an existing network, the
module should be configured. Though all modules are
initially configured at the factory, it is recommended to check
that the baud rate is set correctly.
Default Factory Settings
Baud rate：9600 Bit/sec.
Address：01 (hexadecimal)
Checksum：disable
The basic hook-up for module configuration is shown below.
Figure 2-2 Layout for Initialization the RemoDAQ module
The following items are required to configure a module：a
8
RemoDAQ-8054 User’s Manual
RemoDAQ
converter module, a personal computer with
RS-
232 port (baudrate set to 9600) and theRemoDAQ utility software.
Configuration with the RemoDAQ Utility Software
The easiest way to configure the RemoDAQ module is by
using the RemoDAQ utility software：an easy-to-use menu-
structured program will guide you through every step of the
configuration.
Configuration with the RemoDAQ command set
RemoDAQ modules can also be configured by issuing
direct commands from within a terminal emulation program
that is part of the RemoDAQ utility software.
The following example guides you through the setup of an
analog input module. Assume that RemoDAQ-8054 still has
its default settings (baud rate 9600 and address 01h). Before
the module is reconfigured, it is first requested to send its
default settings.
To change the configuration setting of the analog input
module, the following command is issued：
%0107400600(cr)
% = change configuration
01 = target module at address 00 to：
07 = change address to 07 hexadecimal
40 = set input range to Type 40
06 = set baud rate to 9600
00 = set integration time to 50 ms (60 Hz)
disable checksum
set data format to engineering units
9
Inhaltsverzeichnis
Beliebte Computerhardware Handbücher anderer Marken
EMC2
EMC2 VNX Series Betriebsanleitung
Panasonic
Panasonic DV0PM20105 Bedienungsanleitung
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Bedienungsanleitung
Gigabyte
Gigabyte B660M DS3H AX DDR4 Bedienungsanleitung
Raidon
Raidon iT2300 Bedienungsanleitung
National Instruments
National Instruments PXI-8186 Bedienungsanleitung
