Gendex ORTHORALIX 9200 Bedienungsanleitung

Gendex Dental Systems

901 West Oakton Street

Des Plaines, IL 60018 U.S.A.

Tel 1-888-275-5286

Fax 1-847-550-1322

www.gendex.com

Authorized Representative:

KaVo Dental GmbH

Bismarckring 39

88400 Biberach, Germany

www.gendex-dental.com

www.kavo.com

Ceph Installation Manual

Installation Manual

Gendex Dental Systems

901 West Oakton Street

Des Plaines, IL 60018 U.S.A.

Customer Service 1-888-275-5286

Fax 1-847-550-1322

Technical Support 1-888-275-5286

Fax 1-847-718-0716

www.gendex.com

Ceph Installation

Gendex Dental Systems

901 West Oakton Street

Des Plaines, IL 60018 U.S.A.

Tel 1-888-275-5286

Fax 1-847-550-1322

www.gendex.com

Authorized Representative:

KaVo Dental GmbH

Bismarckring 39

88400 Biberach, Germany

www.gendex-dental.com

www.kavo.com

Installation Manual

-iii032-0296-EN Rev 0

Chapter 1 - Ceph Upgrade

Prerequisites ...................................................................................................... 1-1

Installation ......................................................................................................... 1-1

Ceph Wiring ........................................................................................................ 1-4

Ceph Collimator Alignment ................................................................................. 1-5

Secondary Collimator Alignment ......................................................................... 1-7

String Alignment .........................................................................................................1-7

Vertical Alignment of the Secondary Collimator ..........................................................1-9

Install Primary Collimator ................................................................................. 1-10

Check X-ray Alignment with Static Exposure ..................................................... 1-12

Ear Post Alignment ........................................................................................... 1-13

Table of Contents

032-0296-EN Rev 0-iv

1-11-1

032-0296-EN Rev 0

Chapter

1Ceph Upgrade

Prerequisites

Before starting the installation, make sure the Pan primary collimator alignment is correct.

Installation

The following instructions are for the installation of the Ceph onto a 9200 DDE. The same

procedure is followed for both the new installation of a 9212 DDE and the addition of a

Cephalostat to an existing 9200 DDE. The 9200 DDE can be upgraded to a 9212 DDE with a

Cephalostat at any time.

The Cephalostat requires the installation of a Ceph sensor if the 9200 DDE was originally

ordered without one.

WARNING

High voltage is present in the system. Covers on the equipment should only

be removed by qualified and authorized service personnel. Remove power

from device prior to starting this procedure.

1. Remove the top cover of the overhead assembly.

2 3

Remove the control panel cover (three screws on

top, two on the bottom).

3. Remove the knockout for the mounting of the

ceph arm.

9200 Ceph Installation Manual

032-0296-EN Rev 01-2

Remove control panel cover and carefully

unplug the two touch pad control

connections.

NOTE: Do not disconnect ground wire.

5. Place the cover on top of the overhead.

WARNING

The Ceph requires a two person lift. Failure to comply may cause bodily injury.

Two adults are required to position and assemble this unit.

Carefully feed all five Ceph cables into the overhead.

The cables go through the access hole and up

over the front of the board for connection.

Ceph Upgrade

1-3032-0296-EN Rev 0

Level the Ceph arm front to back while

bolting in place (four screws).

NOTE: To facilitate leveling and minimize

later alignment, have an assistant

support the Ceph assembly up and

towards the rear of the Pan while

tightening the mounting bolts.

Load all Ceph weights into same place in

column, one large then both taped packets.

10.

Remove the shipping bolts and

carriage stop bolt after all components

are mounted and the weights are

inserted into place.

9200 Ceph Installation Manual

032-0296-EN Rev 01-4

Ceph Wiring

1. In the overhead, unplug the

existing connections for X37

and pigtail connections and

replace these connections

with the new arm cable X37

and pigtail.

2. Connect X8 Ethernet cable.

3. Connect X14 arm cable.

Install ferrite filter on X-37

and X-8 cables which are

provided in the accessory

box.

Connect X15 arm cable.

6. Connect X29 arm cable.

1 2

Ceph Upgrade

1-5032-0296-EN Rev 0

Ceph Collimator Alignment

NOTE: The ceph plates are NOT installed.

1. Move the collimator lever to the first

ceph position, LL Max (H-22).

2. Remove the front tubehead cover to

uncover the collimator assembly.

NOTE: The brass plate into the Ceph

collimator location is not yet

installed.

3. Remove Ceph cover plate where

collimator is to be installed.

4. Restore power to the device.

5. Move the DMU to the ceph bay.

6. Press the Reset button.

The Reset Light should illuminate.

7. Remove top cover of ceph.

9200 Ceph Installation Manual

032-0296-EN Rev 01-6

8 9

Loosen 4 screws on secondary collimator

plate and adjust plate to the center of the

screws in the slotted mounting holes.

Secure two screws.

9. Loosen 2 screws on the Opto switch flag

and position flag to center screws to center

screws in the slotted mounting holes.

Secure both screws.

10.

Loosen the belt tension.

11. Manually move the entire secondary

collimator assembly until the opto switch

flag lines up with the center of the opto

switch.

NOTE: Take notice of the small forward

movement of the assembly as the

belt is tightened and adjust

accordingly.

12. Take care not to put undue tension on the

belt.

13. Press Reset to ensure that the device is

able find the Home position.

14. Power down the device.

15.

Put the unit into service mode:

a. Press and hold both Patient

Size and Demo Mode buttons

while simultaneously turning

on the power switch. Hold

both buttons until the service

program shows in the window.

b. Use the cuspid directional

buttons to advance through

the service programs to “X-ray

alignment dummy run to go”.

c. Press the Demo Mode button.

d. Press the Reset button.

5. Proceed to the Secondary

Collimator Alignment.

Andere Handbücher für ORTHORALIX 9200

Inhaltsverzeichnis

Andere Gendex Dentalgeräte Handbücher

Gendex

Gendex Expert DC Bedienungsanleitung

Gendex

Gendex AcuCam Concept IV FWT Bedienungsanleitung

Gendex

Gendex DenOptix QST Bedienungsanleitung

Gendex

Gendex Expert DC Bedienungsanleitung

Gendex

Gendex VisualiX eHD Fehlerbehebungshandbuch

Gendex

Gendex GXP Bedienungsanleitung

Gendex

Gendex GXDP-700 Bedienungsanleitung

Gendex

Gendex ORALIX AC Bedienungsanleitung

Gendex

Gendex ORTHORALIX 8500DDE Bedienungsanleitung

Gendex

Gendex GXS-700 Bedienungsanleitung

Gendex

Gendex eZ1 Montage- und Bedienungsanleitung

Gendex

Gendex ORTHORALIX 8500DDE Bedienungsanleitung

Gendex

Gendex GXS-700 Bedienungsanleitung

Gendex

Gendex ORTHORALIX 8500 Bedienungsanleitung

Beliebte Dentalgeräte Handbücher anderer Marken

Vatech

Vatech EzRay Air VEX-P300 Bedienungsanleitung

KaVo

KaVo GENTLEpower LUX Contra-angle 25 LP Bedienungsanleitung

DENTSPLY

DENTSPLY SmartLite Focus Bedienungsanleitung

LM ProPower CombiLED Bedienungsanleitung

Owandy Radiology

Owandy Radiology RX-AC Bedienungsanleitung

mectron

mectron Piezosurgery Bedienungsanleitung

Belmont

Belmont CREDIA G1 Bedienungsanleitung

Planmeca

Planmeca Sovereign Classic Bedienungsanleitung

Bego

Bego Fornax T Bedienungsanleitung

Renfert

Renfert SYMPRO Kurzanleitung

Ateco

Ateco AT-301 Bedienungsanleitung

Nevadent

Nevadent NZPS 3 A1 Bedienungsanleitung

Dentatus

Dentatus Nyström Bedienungsanleitung

OMS

OMS DUKE EASY Handbuch

OMS

OMS LINEA PATAVIUM Handbuch

BRYANT DENTAL

BRYANT DENTAL Ignis Gesture A-494322 Bedienungsanleitung

Dekema

Dekema AUSTROMAT 664 iSiC Bedienungsanleitung

NSK

NSK Primado2 Bedienungsanleitung