Generac Power Systems 00784-2, 09290-4 Service-Handbuch

POWER SYSTEMS, INC.

Owner’s Manual and

Installation Instructions

Air-cooled Recreational

Vehicle Generators

• Model Nos: 00784-2 and 09290-4

Generac®Power Systems, Inc.

INTRODUCTION

READ THIS MANUAL THOROUGHLY

If you do not understand any portion of this manual,

contact Generac or your nearest Generac Authorized

Service Dealer for starting, operating and servicing pro-

cedures.

Throughout this publication, and on tags and

decals affixed to the generator, DANGER, WARNING,

CAUTION and NOTE blocks are used to alert you to

special instruction about a particular operation that

may be hazardous if performed incorrectly or care-

lessly. Observe them carefully. Their definitions are

as follows:

After this heading, you can read instructions that,

if not strictly complied with, will result in personal

injury or property damage.

After this heading, you can read instructions that,

if not strictly complied with, may result in personal

injury or property damage.

After this heading, you can read instructions that, if

not strictly complied with, could result in damage to

equipment and/or property.

NOTE:

After this heading, you can read explanatory

statements that require special emphasis.

These safety warnings cannot eliminate the hazards

that they indicate. Common sense and strict compli-

ance with the special instructions while performing the

service are essential to preventing accidents.

Four commonly used safety symbols accompany the

DANGER, WARNING and CAUTION blocks. The type

of information each indicates follows:

This symbol points out important safety informa-

tion that, if not followed, could endanger personal

safety and/or property of you and others.

This symbol points out potential explosion hazard.

This symbol points out potential fire hazard.

This symbol points out potential electrical shock

hazard.

The operator (driver) is responsible for proper and

safe use of the vehicle and its equipment, and the safe-

ty of all vehicle occupants. We strongly recommend

that the operator read this manual and thoroughly

understand all instructions before using this equip-

ment. We also strongly recommend instructing other

occupants in the vehicle to properly start and operate

the generator. This prepares them if they need to oper-

ate the equipment in an emergency.

CONTENTS

This manual contains pertinent owner’s information,

including warranty, electrical diagrams, exploded

views and lists of repair parts for generator model

numbers 009290-4 and 00784-2. In addition, the lat-

ter portion of this manual contains information nec-

essary for the proper installation of these generators.

OPERATION AND MAINTENANCE

It is the operator's responsibility to perform all safe-

ty checks, to make sure that all maintenance for safe

operation is performed promptly, and to have the

equipment checked periodically by a Generac

Authorized Service Dealer. Normal maintenance ser-

vice and replacement of parts are the responsibility of

the owner/operator and, as such, are not considered

defects in materials or workmanship within the

terms of the warranty. Individual operating habits

and usage contribute to the need for maintenance

service.

Proper maintenance and care of your generator

ensure a minimum number of problems and keep

operating expenses at a minimum. See your Generac

Authorized Service Dealer for service aids and acces-

sories.

HOW TO OBTAIN SERVICE

When your generator requires servicing or repairs,

simply contact a Generac Authorized Service Dealer

for assistance. Service technicians are factory-trained

and are capable of handling all of your

service needs.

When contacting a Generac Authorized Service Dealer

or the factory about parts and service, always supply

the complete model number and serial number of your

unit as given on its data decal, which is located on your

generator.

Model No. ____________ Serial No. ______________

◆

AUTHORIZED SERVICE

DEALER LOCATION

To locate the GENERAC AUTHORIZED SERVICE

DEALER nearest you, please call this number:

1-800-333-1322

ONLY DEALER LOCATION INFORMATION

CAN BE OBTAINED AT THIS NUMBER.

Table of Contents

PRIMEPACT 50 and 70 (50Hz) Recreational Vehicle Generatorss

Generac®Power Systems, Inc. 1

Part I — Owner’s Manual

Introduction ........................................Inside Front Cover

Read This Manual Thoroughly..................................IFC

Contents ..................................................................IFC

Operation and Maintenance......................................IFC

How to Obtain Service ..............................................IFC

Authorized Service Dealer Locator Number ................IFC

Safety Rules ........................................................................2

Section 1 – General Information....................................4

1.1 Generator Identification ........................................4

1.2 Generator Applicability..........................................5

1.3 Installation ............................................................5

1.4 Safety ....................................................................5

1.5 Generator AC Connection System..........................5

1.6 Specifications ........................................................6

Section 2 – Operation ......................................................7

2.1 Generator Control Panel ........................................7

2.2 Optional Remote Start/Stop Panel ........................7

2.3 Automatic Choke ..................................................7

2.4 Before Starting the Engine ....................................8

2.5 Starting the Generator ..........................................8

2.6 Stopping the Generator ........................................9

2.7 Applying Loads to Generator ................................9

2.8 Protection Systems ................................................9

2.9 Additional Information ........................................10

Section 3 – Maintenance ..............................................11

3.1 Checking the Engine Oil Level ............................11

3.2 Changing the Engine Oil and/or Oil Filter............11

3.3 Maintaining the Engine Air Cleaner ....................12

3.4 Clean Air Intake Screen ......................................12

3.5 Checking the Engine Spark Plug..........................12

3.6 Fuel Filter (Gasoline Only) ..................................13

3.7 Spark Arrestor Muffler ........................................13

3.8 Cleaning the Generator........................................13

3.9 Battery Maintenance ............................................13

3.10 Major Service Manual ..........................................14

3.11 Drive Belt ............................................................14

3.12 Exercising the Generator ....................................14

3.13 Out of Service Procedure ....................................14

3.14 Wattage Reference Guide......................................15

Notes ..................................................................................16

PartII — Installation Instructions

Safety Rules ......................................................................18

Section 1 – General Information ................................20

1.1 Purpose and Scope of the Manual ......................20

1.2 Safety ..................................................................20

1.3 Standards Booklets ............................................20

1.4 Equipment Description........................................20

1.5 Generator Engine Operating Speed ....................20

1.6 Generator AC Connection System........................20

Section 2 – Installation ..................................................22

2.1 Location and Support..........................................22

2.2 Generator Compartments ....................................23

2.3 Cooling and Ventilating Air ..................................26

2.4 Gasoline Fuel System ..........................................27

2.5 Exhaust System ..................................................28

2.6 Electrical connections..........................................29

2.7 Battery Installation ..............................................32

2.8 Optional Accessories............................................32

Section 3 – Post Installation Start-up and

Adjustments ................................................33

3.1 Post Installation Tests..........................................33

3.2 Before Initial Start-up ..........................................33

3.3 Initial Start-up ....................................................33

3.4 Testing Under Load ............................................33

3.5 Installation Checklist ..........................................34

Section4–Troubleshooting ........................................35

4.1 Troubleshooting Guide ........................................35

Section 5 – Electrical Data ............................................36

Section 6 – Exploded Views and Parts Lists ............38

Section7–Warranty......................................................48

2 Generac®Power Systems, Inc.

Study these SAFETY RULES carefully before

installing, operating or servicing this equipment.

Become familiar with this manual and with the unit.

The generator can operate safely, efficiently and reli-

ably only if it is properly installed, operated and main-

tained. Many accidents are caused by failing to follow

simple and fundamental rules or precautions.

Generac cannot possibly anticipate every possible

circumstance that might involve a hazard. The warn-

ings in this manual, and on tags and decals

affixed to the unit, are, therefore, not all-inclusive. If

you use a procedure, work method or operating tech-

nique Generac does not specifically recommend, you

must satisfy yourself that it is safe for you and others.

You also must make sure the procedure, work

method or operating technique that you choose does

not render the generator unsafe.

Despite the safe design of this generator,

operating this equipment imprudently, neglecting

its maintenance or being careless can cause

possible injury or death. Permit only responsible

and capable persons to operate or maintain this

equipment.

Potentially lethal voltages are generated by

these machines. Ensure all steps are taken to

render the machine safe before attempting to

work on the generator.

Parts of the generator are rotating and/or hot

during operation. Exercise care near running

generators.

GENERAL HAZARDS

• For safety reasons, Generac recommends

that the installation, initial start-up and mainte-

nance of this equipment is carried out by a

Generac Authorized Service Dealer.

• The engine exhaust fumes contain carbon monox-

ide, which can be DEADLY. This dangerous gas, if

breathed in sufficient concentrations, can cause

unconsciousness or even death. This exhaust sys-

tem must be installed properly, in strict compli-

ance with applicable codes and standards.

Following installation, you must do nothing that

might render the system unsafe or in noncompli-

ance with such codes and standards. The genera-

tor compartment must be completely vapor sealed

from the vehicle interior. There must be no possi-

bility of exhaust fumes entering the vehicle interi-

or. Never operate this equipment with a leaking or

defective exhaust system.

• Keep hands, feet, clothing, etc., away from drive

belts, fans, and other moving or hot parts. Never

remove any drive belt or fan guard while the unit is

operating.

• Adequate, unobstructed flow of cooling and venti-

lating air is critical to correct generator operation

and is required to expel toxic fumes and fuel

vapors from the generator compartment. Without

sufficient cooling airflow, the engine/generator

quickly overheats, which causes serious damage to

the generator. Do not alter the installation or per-

mit even partial blockage of ventilation provisions,

as this can seriously affect safe operation of the

generator.

• When working on this equipment, remain alert at

all times. Never work on the equipment when you

are physically or mentally fatigued.

• Inspect the generator regularly, and contact your

nearest Generac Authorized Service Dealer immedi-

ately for parts needing repair or replacement.

• Before performing any maintenance on the genera-

tor, disconnect its battery cables to prevent acci-

dental start up. Disconnect the cable from the bat-

tery post indicated by a NEGATIVE, NEG or (–)

first. Reconnect that cable last.

• Never use the generator or any of its parts as a

step. Stepping on the unit can stress and break

parts, and may result in dangerous operating con-

ditions from leaking exhaust gases, fuel leakage,

oil leakage, etc.

Safety Rules

PRIMEPACT 50 and 70 (50Hz) Recreational Vehicle Generators

SAVE THESE INSTRUCTIONS – The manufacturer suggests that these rules for safe

operation be copied and posted in potential hazard areas of the recreational vehicle.

Safety should be stressed to all operators and potential operators of this equipment.

The engine exhaust from this product

contains chemicals known to the state

of California to cause cancer, birth

defects or other reproductive harm.

WARNING:

This product contains or emits chemicals

known to the state of California to cause

cancer, birth defects or other reproductive harm.

WARNING:

Generac®Power Systems, Inc. 3

ELECTRICAL HAZARDS

• The generator covered by this manual produces

dangerous electrical voltages and can cause fatal

electrical shock. Avoid contact with bare wires, ter-

minals, connections, etc., while the unit is running.

Ensure all appropriate covers, guards and barriers

are in place before operating the generator. If you

must work around an operating unit, stand on an

insulated, dry surface to reduce shock hazard.

• Do not handle any kind of electrical device while

standing in water, while barefoot, or while hands

or feet are wet. DANGEROUS ELECTRICAL

SHOCK MAY RESULT.

• During installation onto the vehicle, have the genera-

tor properly grounded (bonded) either by solid

mounting to the vehicle frame or chassis, or by

means of an approved bonding conductor. DO NOT

disconnect the bonding conductor, if so equipped.

DO NOT reconnect the bonding conductor to any

generator part that might be removed or disassem-

bled during routine maintenance. If the grounding

conductor must be replaced, use only a flexible con-

ductor that is of No. 8 American Wire Gauge (AWG)

copper wire minimum.

• In case of accident caused by electric shock, imme-

diately shut down the source of electrical power. If

this is not possible, attempt to free the victim from

the live conductor. AVOID DIRECT CONTACT

WITH THE VICTIM. Use a nonconducting imple-

ment, such as a rope or board, to free the victim

from the live conductor. If the victim is uncon-

scious, apply first aid and get immediate medical

help.

• Never wear jewelry when working on this equip-

ment. Jewelry can conduct electricity resulting in

electric shock, or may get caught in moving com-

ponents causing injury.

FIREHAZARDS

• For fire safety, the generator must be installed and

maintained properly. Installation always must

comply with applicable codes, standards, laws and

regulations. Adhere strictly to local, state and

national electrical and building codes. Comply

with regulations the Occupational Safety and

Health Administration (OSHA) has established.

Also, ensure that the generator is installed in

accordance with the manufacturer’s instructions

and recommendations. Following proper installa-

tion, do nothing that might alter a safe installation

and render the unit in noncompliance with the

aforementioned codes, standards, laws and regu-

lations.

• Keep a fire extinguisher in the vehicle at all times.

Extinguishers rated “ABC” by the National Fire

Protection Association are appropriate for use on

the recreational vehicle generator electrical system.

Keep the extinguisher properly charged and be

familiar with its use. If you have any question per-

taining to fire extinguishers, consult your local fire

department.

EXPLOSION HAZARDS

• Do not smoke around the generator. Wipe up any

fuel or oil spills immediately. Ensure that no com-

bustible materials are left in the generator com-

partment, or on or near the generator, as FIRE or

EXPLOSION may result. Keep the area surround-

ing the generator clean and free from debris.

• Gasoline is extremely FLAMMABLE and its vapors

are EXPLOSIVE. Do not permit smoking, open

flame, sparks or any source of heat in the vicinity

while handling gasoline. Comply with all laws gov-

erning the storage and handling of gasoline.

Safety Rules

PRIMEPACT 50 and 70 (50Hz) Recreational Vehicle Generators

4 Generac®Power Systems, Inc.

Section 1 – General Information

PRIMEPACT 50 and 70 (50Hz) Recreational Vehicle Generators

Please record the following information from the generator DATA DECAL or information decal.

1. Model Number ____________________ 2. Serial Number __________________

3. kW Rating__________________________ 4. Rated Voltage __________________

5. Phase ______________________________ 6. Hertz __________________________

1.1 GENERATOR IDENTIFICATION

REFERENCE NUMBER IDENTIFICATION

1. Generator Air Intake Screen

2. Data Plate

3. Engine Start/Stop Switch

4. 15 amp Fuse

5. 25 or 30 Amp (2 Pole) Circuit Breaker

6. Optional Remote Panel Receptacle

7. Generator AC Output Leads

8. Fuel Inlet

9. Fuel Primer Switch

10. Fuel Pump

11. Oil Filter

12. Starter Contactor

13. Oil Drain Plug

14. Oil Dipstick and Filler Tube

11 10 9

Generac®Power Systems, Inc. 5

Section 1 – General Information

PRIMEPACT 50 and 70 (50Hz) Recreational Vehicle Generators

1.2 GENERATOR APPLICABILITY

These generators have been designed and manufac-

tured for supplying electrical power for recreational

vehicles. You should not modify the generator or use

it for any application other than for what it was

designed. If there are any questions pertaining to its

application, write or call the factory. Do not use the

unit until you have been advised by a competent

authority.

For fire safety, the generator must have been

properly installed in compliance with ANSI

119.2-1975/NFPA 501C-1974, “Standard for

Recreational Vehicles, Part III – Installation of

Electrical Systems.” The generator also must

have been installed in strict compliance with

the manufacturer’s detailed installation instruc-

tions. After installation, do nothing that might

render the unit in noncompliance with such

codes, standards and instructions.

1.2.1 PRIMEPACT 70

Use this generator to supply electrical power for

operating 230-volt, single-phase, 50 Hertz, AC elec-

trical loads. These loads can require up to 7,000

watts (7.0 kW) of power, but cannot exceed 30.4 AC

amperes of current at 230 volts.

1.2.2 PRIMEPACT 50

Use this generator to supply electrical power for

operating 230 volt, single phase, 50 Hertz AC electri-

cal loads. These loads can require up to 5,000 watts

(5.0 kW) of power, but cannot exceed 20.8 amperes of

current at 230 volts.

Do not overload the generator. Some installa-

tions may require that electrical loads be alter-

nated to avoid overloading. Applying exces-

sively high electrical loads may damage the

generator and may shorten its life. Add up the

rated watts of all electrical lighting, appliance,

tool and motor loads the generator will power

at one time. This total should not be greater

than the wattage capacity of the generator. If

an electrical device nameplate gives only volts

and amps, multiply volts times amps to obtain

watts (volts x amps = watts). Some electric

motors require more watts of power (or amps

of current) for starting than for continuous

operation.

1.3 INSTALLATION

This manual has been prepared under the assump-

tion that a competent, qualified technician installed

the generator into a recreational vehicle. We also

assume the installer complied with all applicable

codes, standards and regulations pertaining to instal-

lation.

Owners/Operators should make sure nothing is done

during installation that might render the unit unsafe

or in noncompliance with applicable codes standards

and instructions. They should be sure the unit has

been installed to allow adequate ventilation for cool-

ing and exhaust air.

1.4 SAFETY

Before attempting to use the generator set, carefully

read the “Safety Rules” section of this manual.

Comply strictly with these rules to prevent accidents

and damage to equipment and/or property. We sug-

gest copying and posting the “Safety Rules” in poten-

tial hazard areas of the vehicle. Stress safety to all

operators and potential operators of this equipment.

1.5 GENERATOR AC

CONNECTION SYSTEM

This generator set is equipped with dual stator AC

power windings. These two-stator windings supply

electrical power to customer electrical loads.

NOTE:

One side of the winding is grounded.

Figure 1.1 – Connections for 230 Volts Only

◆

6 Generac®Power Systems, Inc.

Section 1 – General Information

PRIMEPACT 50 and 70 (50Hz) Recreational Vehicle Generators

1.6 SPECIFICATIONS

1.6.1 FUEL REQUIREMENTS

These generators are equipped with a gasoline fuel sys-

tem. Depending on the installation, the generator may

have either a separate fuel tank, or it may “share” the

vehicle engine’s fuel tank.

NOTE:

Some installations using a “shared” fuel tank may

have a generator fuel pickup tube that is shorter

than the vehicle engine’s pickup tube. Such an

arrangement causes the generator engine to “run

out of gas” while adequate fuel for the vehicle

remains in the tank.

To reduce lead and carbon deposits use high quality

UNLEADED gasoline with the generator. Leaded REG-

ULAR grade gasoline is an acceptable substitute.

NOTE:

Using unleaded gasoline contributes to longer

engine valve life by reducing lead and carbon

deposits.

Generac does not recommend using any

gasoline containing alcohol (such as “gasohol”).

If you use any gasoline containing alcohol, it

must not contain more than 10 percent ethanol,

and it must be removed from the generator

during storage. Do NOT use any gasoline

containing methanol. If you use gasoline with

alcohol, inspect more frequently for fuel leaks

and other abnormalities.

1.6.2 ENGINE OIL REQUIREMENTS

Use only high quality detergent oil classified “For

Service SF” and with an oil viscosity rating of SAE

10W-30 oil. Do not pour in any additives to the rec-

ommended oil. Engine crankcase capacity is 1.4

liters. See Section 3.2 on page 11 for oil level check

and filing procedures.

1.6.3 ENGINE

Type of Engine ......................................GN-480, Twin-cylinder

Cooling Method..........................................................Air-cooled

Rated Horsepower ..........................................16 @ 3,600 rpm

Displacement ....................................................................480cc

Compression Ratio........................................................8.6 to 1

Cylinder Block ..........................Aluminum w/Cast Iron Sleeve

Type of Governor ..............................Mechanical, Fixed Speed

Engine Governor Speed ............................................3000 rpm

Air Cleaner..........................Paper Element w/Foam Precleaner

Starter..........................................................12-volt DC Electric

Ignition System........................Solid-state w/Flywheel Magneto

Recommended Spark Plug

Champion ..................................................................RC12YC

AC....................................................................................R45S

Fram Autolite ......................................................................65

Spark Plug Gap........................................0.030 inch (0.8 mm)

1.6.4 GENERATOR PP50G/PP70G

Rated Maximum Continuous

AC Output ....................5,000 (5.0 kW)/7,000 Watts (7.0 kW)

Rated Voltage ..............................................................230 Volts

Rated Maximum Continuous

AC Current ................................21.8 Amperes/30.4 Amperes

Phase ................................................................................Single

Rotor RPM ........................................................................3,000

Number of Rotor Poles ............................................................2

Engine RPM............................................................2,900/3,000

Rated AC Frequency ........................................................50 Hz

Weight......................................................................222 Pounds

Length........................................................25 inches (635 mm)

Width ..................................................18.5 inches (469.9 mm)

Height..............................................16.75 inches (425.45 mm)

◆

Generac®Power Systems, Inc. 7

Section 2 – Operation

PRIMEPACT 50 and 70 (50Hz) Recreational Vehicle Generators

2.1 GENERATOR CONTROL PANEL

The following features are mounted on the generator

control panel (Figure 2.1):

Figure 2.1 – Generator Control Panel

2.1.1 FUEL PRIMER

Before starting a cold engine (if it has not been start-

ed in more than two weeks), you must press this

switch for approximately five seconds to bring fuel

from the tank to the fuel pump. This rocker type

switch springs back into its original position when

you release it.

2.1.2 START/STOP SWITCH

To crank and start the engine, hold this switch in the

START position. Release the switch when the engine

starts. To stop an operating engine, press and hold

the switch in the STOP position until the engine shuts

off. The switch center position is the RUN position.

2.1.3 FUSE

The fuse protects the engine’s DC control circuit

against electrical overload. If the fuse element has

melted open due to overloading, the engine cannot be

cranked. If you must replace the fuse, use only an

identical replacement.

2.1.4 MAIN BREAKER

The main breaker protects the generator’s AC output

circuit against overload and provides a method of

turning OFF the generator’s 230-volt AC output to the

vehicle circuits. These generators have either a 25

Amp, 2-Pole circuit breaker (PP50) or a 30 Amp

2-Pole circuit breaker (PP70).

2.2 OPTIONAL REMOTE

START/STOP PANEL

A remote mounted Start/Stop Panel (Figure 2.2) is

available that allows you to start and stop the gener-

ator engine conveniently from inside the vehicle. The

remote panel includes a Start/Stop switch, hour

meter, generator run lamp and a wire harness.

Figure 2.2 — Optional Remote Panel

(Models 004057 and 004184)

2.3 AUTOMATIC CHOKE

This engine is equipped with an automatic choke that

consists of two main components: a choke solenoid

and prechoke.

2.3.1 CHOKE SOLENOID

During engine cranking (Start/Stop switch at

START), a solid-state choke module signals the

choke solenoid to activate and cycle (choke on/choke

off) until the engine starts. The choke solenoid thus

opens and closes the carburetor choke valve only

when the engine is cranking. When the engine starts,

the choke stops cycling.

2.3.2 PRECHOKE

The choke system also has a temperature-sensitive

metal strip that adjusts choke valve angle according

to ambient temperatures (i.e., in cold ambient tem-

peratures, choke valve closes more). Once the engine

starts, an element heats the temperature-sensitive

strip to a normal operating condition, opening the

choke valve. This may take about three minutes in

cooler weather.

◆

8 Generac®Power Systems, Inc.

Section 2 – Operation

PRIMEPACT 50 and 70 (50Hz) Recreational Vehicle Generators

2.4 BEFORE STARTING THE ENGINE

NOTE:

Instructions and information in this manual

assume the generator has been properly installed,

connected, serviced, tested and adjusted by a

qualified installation technician or installation

contractor.

2.4.1 INSTALLATION

Generator installation must have been properly com-

pleted so it complies with all applicable codes, stan-

dards and regulations and with the manufacturer's

recommendations.

2.4.2 ENGINE LUBRICATION

Have the engine crankcase properly serviced with the

recommended oil before starting. Refer to Section 1.6.3

(Page 6) and Sections 3.1 and 3.2 (Page 11) for oil ser-

vicing procedures and recommendations.

Any attempt to crank or start the engine before

you have properly serviced it with the recom-

mended oil may result in an engine failure.

2.4.3 FUEL SUPPLY

The engine must have an adequate supply of proper

fuel to operate. Before starting it, check that sufficient

fuel is available.

NOTE:

Depending on the installation, the generator may

have either a separate fuel tank, or it may “share”

the vehicle engine’s fuel tank.

2.4.4 COOLING AND VENTILATING AIR

Air inlet and outlet openings in the generator com-

partment must be open and unobstructed for contin-

ued proper operation. Without sufficient cooling and

ventilating airflow, the engine/generator quickly over-

heats, which causes it to shut down and may damage

the generator.

2.4.5 ENGINE EXHAUST GAS

Before starting the generator engine, you should be

sure there is no way for exhaust gases to enter the

vehicle interior and endanger people or animals.

Close windows, doors and other openings in the vehi-

cle that, if open, might permit exhaust gases to enter

the vehicle.

The generator engine gives off DEADLY carbon

monoxide gas through its exhaust system. This

dangerous gas, if breathed in sufficient concen-

trations, can cause unconsciousness or even

death. Never operate the generator set with

the vehicle inside any garage or other enclosed

area. DO NOT OPERATE THE GENERATOR IF THE

EXHAUST SYSTEM IS LEAKING OR HAS BEEN

DAMAGED. SYMPTOMS OF CARBON MONOX-

IDE POISONING ARE (a) inability to think coher-

ently; (b) vomiting; (c) twitching muscles; (d)

throbbing temples; (e) dizziness; (f) headaches;

(g) weakness; and (h) sleepiness. IF YOU FEEL

ANY OF THESE SYMPTOMS, MOVE INTO FRESH

AIR IMMEDIATELY. IF SYMPTOMS PERSIST, GET

MEDICAL HELP.

2.5 STARTING THE GENERATOR

To start the generator from either the generator con-

trol panel or from the optional remote panel, proceed

as follows:

1. Turn OFF electrical loads using the means pro-

vided in your vehicle (such as a main line circuit

breaker or transfer switch).

NOTE:

If starting from the generator control panel, turn

OFF loads by setting the generator’s main circuit

breaker to the OFF (or open) position. If starting

from a remote panel, turn OFF loads using the

means provided in the vehicle (such as a main cir-

cuit breaker). Electrical load circuits will be

turned ON after the generator has started, stabi-

lized and warmed up.

2. If you have not started the engine in more than

two weeks, press the Fuel Pump Primer switch

and hold it for about five seconds to prime the

fuel system. However, if the engine is warm, skip

Step 2.

3. Hold the engine Start/Stop switch in the START

position to crank the engine. Release the switch

when the engine starts.

If the engine does not start after it has been

cranking for 15 seconds, release the Start/Stop

switch and try again. Holding the switch for

longer than 15 seconds can damage the

starter motor.

4. Let the engine run at no-load for a few minutes to

stabilize and warm up.

5. Turn ON electrical loads using the means

provided (such as a main circuit breaker or

transfer switch).

◆

Inhaltsverzeichnis

Andere Generac Power Systems Wechselrichter Handbücher

Generac Power Systems

Generac Power Systems MMG35FH Bedienungsanleitung

Generac Power Systems

Generac Power Systems Quietsource 005220-0 Bedienungsanleitung

Generac Power Systems

Generac Power Systems PV Link Bedienungsanleitung

Generac Power Systems

Generac Power Systems QuietSource 005028-0 Bedienungsanleitung

Generac Power Systems

Generac Power Systems A-2624 Bedienungsanleitung

Generac Power Systems

Generac Power Systems 8 kW LP Bedienungsanleitung

Generac Power Systems

Generac Power Systems 004700-0 Montageanleitung

Generac Power Systems

Generac Power Systems 6103 EcoGen Merkblatt

Generac Power Systems

Generac Power Systems Transfer Switches and Accessories Bedienungsanleitung

Generac Power Systems

Generac Power Systems GP1200I Bedienungsanleitung

Generac Power Systems

Generac Power Systems Whisper - Test UL 2200 Bedienungsanleitung

Generac Power Systems

Generac Power Systems 00941-3 Service-Handbuch

Generac Power Systems

Generac Power Systems QuietSource 004917-5 Montageanleitung

Generac Power Systems

Generac Power Systems Guardian 004188-1 Bedienungsanleitung

Generac Power Systems

Generac Power Systems 15 kW EcoGen Merkblatt

Generac Power Systems

Generac Power Systems 04673-2 Montageanleitung

Generac Power Systems

Generac Power Systems Guardian Elite Whisper Test 5261 Bedienungsanleitung

Generac Power Systems

Generac Power Systems Magnum MGG100M Bedienungsanleitung

Generac Power Systems

Generac Power Systems Guardian 04389-2 Montageanleitung

Generac Power Systems

Generac Power Systems 004090-2, 004091-2, 004092-2, 004093-2, 004094-2, 004095-2, 004096-2, 004097-2, 004474-0, 004124-1, 004125-1, 004126-1... Bedienungsanleitung

Generac Power Systems

Generac Power Systems ECOGEN SERIES Bedienungsanleitung

Generac Power Systems

Generac Power Systems 004270-2 Montageanleitung

Generac Power Systems

Generac Power Systems MD1000GEM Installationsanleitung

Generac Power Systems

Generac Power Systems 10 kW LP Betriebsanleitung

Beliebte Wechselrichter Handbücher anderer Marken

Fourgroup

Fourgroup Easy Bedienungsanleitung

Velleman

Velleman PI300M Bedienungsanleitung

Sungrow

Sungrow SG350HX-US Bedienungsanleitung

WilTec

WilTec 61897 Bedienungsanleitung

SMA

SMA SUNNY BOY STORAGE 2.5 Bedienungsanleitung

Simplicity

Simplicity LANDLORD 316 Bedienungsanleitung

Santak

Santak SMAX 3000 Bedienungsanleitung

ATON

ATON RA.Store-3 Bedienungsanleitung

ZIEHL-ABEGG

ZIEHL-ABEGG FXET4AMQ Bedienungsanleitung

Tektronix

Tektronix CFG250 Bedienungsanleitung

Champion

Champion 200989 Bedienungsanleitung

Vanner

Vanner 20-500 Series Bedienungsanleitung

GE GEP Bedienungsanleitung

MULTIQUIP

MULTIQUIP GDP-5H Leitfaden

Astrel Group

Astrel Group Power Reducer Kurzanleitung

GoWISE

GoWISE PS1007 Bedienungsanleitung

Promate

Promate PM13500D ES Bedienungsanleitung

Mastervolt

Mastervolt WHISPER 3.5M3000 RPM Bedienungsanleitung