GENI MOVING HEAD OBY-5 Bedienungsanleitung

WWW.BEGLEC.COM

Exclusive Distribution:

Description of the appearance

Inspection

Carefully unpack the carton, and make sure if any damage or loss

caused by transportation.

Contact your Geni dealer to assure your right by telephone or

facsimile immediately if damage has occurred or if something is

missing.

Packing List:

A. OBY-5 Moving Head

B.Operating Manual

D.GOBO

E. Lamps (Optional)

Bracket

Safety instructions

This appliance must be earthed (grounded).

Disconnect power before removing covers or servicing.

Keep case closed while operating.

OBY-5 contains no user serviceable parts. Refer servicing to

qualified technicians only.

Lamp and components become hot during operation. Allow time to

cool before handling.

Keep flammable material at least one meter away from unit.

Do not operate in wet conditions or near liquids.

Keep air vents clear to avoid overheating.

Lamp produces hazardous UV light. Do not look directly at lamp

when lit.

Replace any blown or damaged fuses only with those of identical

values.

Lamp Installation

When replacing the lamp, please wait 15 minutes after powering down to allow the

unit to cool down! Always disconnect from main power prior to lamp replacement.

Do not touch the envelope (glass area) of the bulb with bare hands. If this happens,

clean the lamp with alcohol and wipe it with a lint free cloth before installation.

Warning!

3,4

1.Keep projector-head upward .Unscrew

thumbscrews (S1) to detach the top

cover.

2. Unscrew screws (S2) to remove lamp

cover and expose lamp compartment.

3. If installing a new lamp, loosen both

screws on the double ended lamp to

allow for the lamp to slide into the

lamp socket slots. Lower lamp

evenly.

4. If replacing a lamp, loosen both lamp

screws (S3) to relieve tension from

lamp socket slots so you can slide the

lamp freely, upwards and out of lamp

socket. Raise lamp evenly to remove.

5. Before you tighten the lamp end

screws, rotate the bulb until the nipple

on the envelope (N) of the bulb is facing

upwards as illustrated.

6. If you are replacing the lamp, you may

want to log the fixture hours in order to

track the lamps use. Navigate to the

(LPti)on the menu display to obtain this

information.

a a

OBY-5 can be set on the flat stage floor directly or use clamp to mount on

any kinds of trusses for fitting the mobility of various venues.

Mount two attached brackets(a) on the bottom (See Figure ), and

collocate the appropriate clamps(b) to rig with trusses. Must use the

safety ropes that can hold the ten times as heavy as the fixture through

the eye bolts(c) on the bottom of the base and trusses; then join the

safety ropes with screw-on carabines(d).

Rigging:

Linking

Use 3-pin XLR data cables to link the controller to DMX lighting

equipment.

3-pin XLR connectors are follows:

Building a serial DMX-chain:

Connect the DMX output of the first fixture with the DMX input of the

next fixture. And execute all the setups following the above-

mentioned instruction.

Flip the DIP SWITCH #3 of last fixture to ON position for terminal

confirmation.

1 2

1:Ground

2:Signal(-)

3.Signal(+)

1:Ground

2:Signal(-)

3.Signal(+)

DMX-output

XLR mounting-socket:

DMX-input

XLR mounting-plug:

Connection with the mains

Connect the device to the mains with the power-plug.

The occupation of the connection-cables is as follows:

The earth has to be connected! In general, lighting effects should not

be connected to dimming-packs.

Instructions for gobo replacement

Plea se cho ose the sui table go bo dimen sion s of this fixtur e. (App endi x A)

3.Push GOBO & the spring ring out with the

fingers carefully. (*Caution: Avoid falling

the spring ring into the fixture.)

2.Turn the open (circle) of the GOBO wheel to

"U" shape gap in order to extract the rotating

GOBO easily.

Rotating GOBO wheel

1.Open the top cover (*Refer to the steps of lamp installation.), and

loosen the screws with appropriate tools then extract A . (See the

figures below.)

4.Insert the new GOBO and the spring ring (*Press the spring ring

tight with the appropriate tools in order to keep GOBO compact),

put A back and screw up the top cover.

Fixed GOBO wheel

The instructions are the same as changing the rotating GOBO; only

winkle the spring ring out with appropriate flat screw driver before

push GOBO out.

DANGER!

Install the gobos with the device switched

off only. Unplug from mains before!

Andere Handbücher für MOVING HEAD OBY-5

Andere GENI Beleuchtungsausrüstung Handbücher

GENI

GENI IRDW-7024156-00D-11 Bedienungsanleitung

GENI

GENI MOVING HEAD OBY-3 Bedienungsanleitung

GENI

GENI OBY-600 WASH Bedienungsanleitung

GENI

GENI Mojo Spin Master MJS-1 Technisches Datenblatt

GENI

GENI COLOR BLASTER CB-250 COLOR BLASTER CB-250B Bedienungsanleitung

GENI

GENI MOVING HEAD OBY-5 Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

Alien

Alien RG STAR Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Bedienungsanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung