Genie GEB Bedienungsanleitung
User Manual
Please read these instructions carefully before operating the unit
and keep for further reference.
2MP 4-in-1 IR Eyeball Camera
with 2.8mm Lens
GEB | GEBG
ii
Intro Section
CAUTION:
• To reduce the risk of electric shock, do not open the camera, please consult a
professional or contact your distributor.
• To prevent fire or shock hazards, the power, input voltage, current, voltage
polarity and operating temperature of this camera must meet the requirements
stated.
• Please note the operating temperature and environmental requirements of
the camera and avoid too low or too high temperatures. General operating
temperature range of -10°C+50°C (Fahrenheit temperature is 14°F~122°F). Avoid
anywhere where there is flooding, rain, dust and moisture erosion that will
cause the camaera to be damaged.
• When installing the camera, you should avoid direct sunlight and glare which
can cause damage to the sensor.
• Do not touch the sensors surface, if you see any marks or small particles use
a cotton swab or lens paper to wipe away. If it is difficult to remove, a neutral
detergent diluted with water would be useful. Do not use any solutions that are
corrosive.
• In order to make the camera work smoothly and obtain a satisfactory image,
the power cord and video connection can not be too long, otherwise this will
increase line loss which will lead to the inadequate magnitude of the operating
voltage or video signal of the camera.
• In order to prevent the camera from falling, please do not place the camera
on an unstable bracket, base or other objects. It will lead to the camera being
damaged, at the same time, a possible injury.
• The camera cannot be placed near a radiator or any heat resistor.
Contents
iii
1.0 Introduction..........................................................................................................4
1.1 Product Features...........................................................................................4
1.2 Product Dimensions.....................................................................................4
1.3 Specification.................................................................................................5
2.0 OSD Menu Tree ....................................................................................................6
3.0 Product Installation..............................................................................................7
3.1 Note ..............................................................................................................7
3.2 Installation Method......................................................................................7
3.3 Product Connection ....................................................................................8
4.0 FAQ’s ....................................................................................................................9
4
The Genie GEB is a high definition discreet eyeball design camera with the
latest 4-in-1 AHD, TVI, CVI and CVBS technologies (fully selectable). The camera
utilises a 2.8mm fixed lens and with a 2MP 1080p resolution, providing a superb
quality image suitable for most general applications both indoors and outdoors.
The camera OSD menu enables many options to be chosen including different
languages, with the camera housing being available in a white or grey finish.
1.1 Product Features
• 1/2.7” 2MP CMOS
• AGC, AWB, AES
• 2D-DNR, 3D-DNR, D-WDR
• Multi-language OSD control from recorder
• Multi-technology (AHD, TVI, CVI and CVBS) output
• DC12V
• NDAA compliant
1.2 Product Dimensions
1.0 Introduction
81.7mm
105.9mm 93.2mm
User Manual 2MP 4-in-1 IR Eyeball Camera with 2.8mm Lens
5
1.3 Specification
Camera
Image Sensor 1/2.7” 2MP CMOS
Image Size 1958 × 1105
Image System PAL / NTSC
Resolution 2MP
Electronic Shutter Auto
Synchronisation Internal synchronisation
Minimum Illumination 0 Lux (IR On)
Lens 2.8 mm
S / N Ratio ≥41dB (AGC Off)
Video Output AHD, TVI, CVI (1080p @ 25fps, 1080p @ 30fps) / CVBS (1280 x
576, 1280 × 480)
Functions
IR Distance Up to 30m
IR LED 2 Pcs
Functional Control OSD (Multi-language)
Day & Night True day / night, Smart, Colour, B&W
DNR 2D-DNR, 3D-DNR
AGC Auto
White Balance Auto / Manual
Others
Ingress Protection IP66
Power Supply DC12V (± 10%)
Power Consumption <4W
Working Environment
Storage: -20°C ~ 60°C,
Working: -10°C ~ 60°C,
Humidity: 90% or less
(Non-condensing)
Dimensions 93.2 × 81.7 mm
Weight 320g
6
2.0 OSD Menu Tree
7
3.1 Note
1. Make sure the unit is powered off before installation.
2. Check that the power supply voltage is consistent with the electric voltage to
prevent damage to the device.
3. Do not use in an environment beyond the boundaries of the temperature, and
maintain good ventilation to prevent the risk of fire or electric shock.
4. The installation and maintenance of this product should be professional, please
do not in any way remove or modify the equipment and only use the required
accessories from the manufacturers. Problems caused by unauthorised repair
are at your own risk
5. Before installation, please prepare the following tools:
• A straight or a Phillips-head screwdriver
• Multi-meter
• Scissors
• Needle nose pliers
• Tape measure
• Pencil
3.2 Installation Method
1. Check the equipment and make sure you have everything you need.
2. Mount the bracket or base. If it’s a cement wall you will need to install using the
expansion screws that need a stand or base hole, and then mount the bracket
or base. If it’s a wooden wall, use self-tapping screws to mount.
3. When mounting the camera, adjust the lens position and make sure it’s aimed
at the monitoring points with a clear picture. Manually fix the lens location and
adjust the hemisphere cover. Re-examine the screen to see whether the camera
meets the requirement. Tighten the hemisphere cover.
Note: The wall needs to bear at least 3x the weight of bracket (base) and camera.
3.0 Product Installation
User Manual 2MP 4-in-1 IR Eyeball Camera with 2.8mm Lens
8
3.3 Product Connection
9
Q: No picture with power on
A: It may result from abnormal power supply. Please check if the power supply
voltage and its polarity are correct. Also you will need to confirm if the wire
connections and monitors are normal.
Q: Unclear image output
A: It is caused by incomplete adjustment of the lens back focus. Loosen the fixed
screw of the lens until it turns clear. If not, please check if the lens is in good
condition, or the lens surface and sensor surface is clear. If not, please wipe with a
degreasing cotton swab or lens paper.
Q: Horizontal interference fringes on image
A: This is generally caused by too strong of a hum bar of power supply which
needs to be filtered out. It may also be related to the used monitor or peripheral
devices.
Q: Constantly change of the ground color of image
A: This is caused by colour scrolling, which is mainly due to alternating
electromagnetic field of fluorescent lamp, and the inherent phenomenon of
camera. It can be weakened with two methods: one is to reduce the usage
of fluorescent lamp. The other is to enlarge the distance with the camera. To
overcome it thoroughly, please select LL synchronisation camera.
4.0 FAQ’s
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Genie Digitalkamera Handbücher
Genie
Genie SSAHD2B Bedienungsanleitung
Genie
Genie WIPX8EBVAF5 Bedienungsanleitung
Genie
Genie GEBV Bedienungsanleitung
Genie
Genie WHD5EBVAF Bedienungsanleitung
Genie
Genie WHD8EB Bedienungsanleitung
Genie
Genie GHDPIR Bedienungsanleitung
Genie
Genie WHD5EB Bedienungsanleitung
Genie
Genie GHD190DV Bedienungsanleitung
Genie
Genie MSC Series Bedienungsanleitung
Genie
Genie WIP2FRTMTP Bedienungsanleitung
Genie
Genie WHD8BVAF Bedienungsanleitung
Genie
Genie WAHD2EBVAF Bedienungsanleitung
Genie
Genie WHD8EBVAF Bedienungsanleitung
Genie
Genie GAHDB650IR Bedienungsanleitung
Genie
Genie GIPPIR Bedienungsanleitung
Genie
Genie HDMC221V2 Bedienungsanleitung
Genie
Genie WAHD8162 Bedienungsanleitung
Genie
Genie WIPX4EB Bedienungsanleitung
Genie
Genie PWIP4EB Bedienungsanleitung
Genie
Genie WAHD2BVAF Bedienungsanleitung
