Genie Universal 4-Button Bedienungsanleitung

Page 1

ALTERNATE INSTRUCTIONS

UNIVERSAL 4-BUTTON REMOTE

General Notes - This document contains alternate instructions for:

•Fixed Code/Dip Switch programming in remotes with software REVs v1.1.4 and higher

oAnother way to tell if you have software REV v1.1.4 or higher –Press and hold down

button #1. While still holding down button #1, press button #4 on the remote four

times, then release both buttons. If the white LED flashes then your software is v1.1.4

or higher.

•The Quick Start Method of programming for any software REV

•TEACH & PAIR programming method in software REVs v1.1.8 and lower. The software REV

of your remote can be found on etched on the back

oAnother way to tell if you have software REV v1.1.8 or lower –if you hold press and

hold down button #1 –while still holding down button #1, press button #2 on the

remote four times, then release both buttons. If the white LED flashes slowly, then

your software is v1.1.8 or lower.

•Information on programming to Marantec openers with the TEACH & PAIR method

Page 1: General Notes

Page 2-3: Fixed Code/Dip Switch Programming

Page 4: Quick Start Method –Using the Pre-Programmed Remote Settings

Page 5-6: TEACH & PAIR Programming Method

Page 7: TEACH & PAIR Programming Method with Marantec® openers

Page 2

ALTERNATE INSTRUCTIONS

DIP SWITCH / FIXED CODE PROGRAMMING

Step 1: Record Switch Positions

▪Each shaded box below represents a switch position. In these boxes, write in the number 1,

2 or 4 as it corresponds to the +, 0, or –switch position shown on the remote, opener or

receiver. If you have less than 12 switches, only fill in what you have. You will reference this

section in STEP 3.4 below.

Step 2: Determine Specifications

▪Find your specification from CHART B below and record the number here:

This box should have one number between 1-8. You will reference this in STEP 3.9 below.

Available in remotes with software REVs v1.1.4 and higher

If the opener has a group of switches with 3 positions per switch (TRINARY):

▪Switch in the UP (+) position = press button 1

▪Switch in the MIDDLE (0) position = press button 2

▪Switch in the DOWN (-) position = press button 4

In this example, the code would be:

If the opener has a group of switches with 2 positions per switch (BINARY):

▪Switch in the UP (+) position = press button 1

▪Switch in the DOWN (-) position = press button 4

In this example, the code would be:

Page 3

Step 3: Programming

ENTER LEARN MODE:

1. On the universal remote, press and hold down button #1.

2. While still holding down button #1, press button #4 on the universal remote four

times.

3. Release both buttons - The WHITE LED on the remote will quickly flash 4 times.

ENTER DIP SWITCHES:

4. On the universal remote, enter in order the numbers 1, 2 or 4 as you have written in

STEP 1. The LED lights with each button press.

5. After the last DIP switch position entry, simply wait for the BLUE LED to quickly flash

4 times and go out.

ENTER BUTTON SELECTION MODE:

6. On the universal remote, press and hold down button #2.

7. While still holding down button #2, press button #3 on the universal remote four

times.

8. Release both buttons - the BLUE LED on the remote will begin flashing.

9. Press the button of your choice on the universal remote the required number of

times indicated from Chart B in STEP 2 above. You will have 10 seconds to complete

your entry.

10.After your press(es), simply wait the remainder of the 10 seconds - the BLUE LED will

give a long blink and then go out.

Page 4

The Quick Start Method uses the pre-programmed manufacturer specifications on the universal

remote.

ALTERNATE INSTRUCTIONS

QUICK START METHOD

Reference FIG 1 to use any of these four manufacturer pre-sets to quickly program a button

Button 1: Genie Intellicode 1 or Overhead Door CodeDodger I

Button 2: Chamberlain® with a PURPLE LEARN Button

Button 3: Chamberlain® with an ORANGE/RED LEARN Button

Button 4: Chamberlain® with a YELLOW LEARN Button*

If using Button 1, 2 or 3:

1. On the garage door opener, press the LEARN button for 2-3 seconds and then release.

2. On the universal remote, press and release the pre-set button that corresponds with your

opener once every 2 seconds until the garage door opener operates. Programming is

complete.

TIP: Allow the LED light on the universal transmitter to stop flashing before your next button

press.

*If using Button 4 for a YELLOW LEARN Button from Chamberlain, LiftMaster or Craftsman:

1. Press and hold down the button #4 for 5 seconds - release button after white LED blinks 3

times and goes out.

1a. ONLY IF you had to manually change your Yellow Learn Button opener to a

390MHz due to interference issues - simply press and hold the button in the step

above for 10 seconds - after the white LEDs blink for the second time - all LEDs will

go out completely - then release the button. If you did not have to manually change

the opener to 390MHz, ignore this line 1a.

2. On opener, press LEARN/PROGRAM button for 2-3 seconds and then release.

3. On remote, press button you chose ONE time. Opener will click.

4. On opener, press LEARN/PROGRAM button again for 2-3 seconds and then release.

5. On remote, press button you chose again ONE time. Opener will click again.

The next button press should operate the opener.

TIP: Allow the LED light on the universal transmitter to stop flashing before your next button

press.

Available in remotes with any software REV.

Page 5

IMPORTANT: For ID#4 Chamberlain®/LiftMaster®/Craftsman® Yellow Learn Button - move

immediately to instructions on pg 6. For all other ID#s, proceed. For a brief explanation on

Marantec® openers, see pg 7.

ALTERNATE INSTRUCTIONS

TEACH & PAIR PROGRAMMING METHOD

for all openers EXCEPT ID#4 Yellow Learn Button

1. On universal remote, press and hold down button #1

2. While still holding down button #1, press button #2 on universal remote four times

3. Release both buttons - WHITE LED flashes slowly.

4. Place the existing, operational remote and universal remote within 4” of each other

5. Hold down the operational button from the original remote. Do not release until the

new universal remote blinks change from slow WHITE blinks to rapid BLUE blinks. You

will have 20 seconds to complete.

TIP: If the universal remote does not recognize the transmission, try different distances between 0”-4”

away from the side of the universal remote closest to button numbers 1 and 3.

6. Once the universal remote BLUE LED is blinking rapidly, press the button of choice on

the universal

remote ONE TIME. The BLUE LED turns solid and goes out.

7. On opener, press LEARN/PROGRAM button for 2-3 seconds and then release.

8. Press and release button you just programmed once every 2 seconds until the garage

door opener

operates.

9. Test the button - programming is complete.

TIP: Allow the LED light on the universal transmitter to stop flashing before your next button press.

Available in remotes with software REVs v1.1.8 and lower (also allows FAAC receiver compatibility)

Page 6

1. On universal remote, press and hold down button #1.

2. While still holding down button #1, press button #2 on universal remote four times.

3. Release both buttons - WHITE LED flashes slowly.

4. Place the existing, operational remote and universal remote within 4” of each other.

5. Hold down the operational button from the original remote. Do not release until the

new universal

remote blinks change from slow WHITE blinks to rapid BLUE blinks. You will have 20

seconds to complete.

TIP: If the universal remote does not recognize the transmission, try different distances between 0”-

4”away from the side of the universal remote closest to button numbers 1 and 3.

6. Once the universal remote BLUE LED is blinking rapidly, press the button of choice on

the universal

remote ONE TIME. The BLUE LED turns solid and goes out.

7. Press and hold down the button you just chose on the universal remote until the white

LED blinks 3 times and goes out (@5 seconds)

7a. ONLY IF you had to manually change your Yellow Learn Button opener to a

390MHz due to interference issues - simply press and hold the button in the step

above for 10 seconds - after the white LEDs blink for the second time - all LEDs

will go out completely - then release the button. If you did not have to manually

change the opener to 390MHz, ignore this line 7a.

8. On opener, press LEARN/PROGRAM button for 2-3 seconds and then release.

9. On remote, press button you chose ONE time. Opener will click.

10.Repeat STEPs 8 & 9.

11.Test the button - programming is complete.

TIP: Allow the LED light on the universal transmitter to stop flashing before your next button press.

TEACH & PAIR PROGRAMMING METHOD

for ID#4 Chamberlain®/LiftMaster®/Craftsman®Yellow Learn Button ONLY

Page 7

ALTERNATE INSTRUCTIONS

MARANTEC® and TEACH & PAIR PROGRAMMING

METHOD

General Information:

Marantec openers only allow ‘one’ set of code inside the operator. The transmitter(s) and/or keypad that came

with the opener are set to this single code.

When adding the universal transmitter to the existing Marantec family, the TEACH & PAIR programming method

should be used. This programming method allows the universal transmitter to listen and then repeat back that

existing transmission, becoming part of that single code family. If you use the LEARN method of programming with a

Marantec opener instead of the TEACH & PAIR method, it will generate a NEW code and WILL WORK with the

opener… BUT the existing transmitter/keypad family will no longer work.

How to program a Marantec opener using the TEACH & PAIR method:

1. Follow the TEACH & PAIR instructions on the previous page for all ID#s EXCEPT #4 –STOP after you have

completed STEP 6. Continue at STEP 7 in the instruction below.

On the Marantec opener:

7. To start the system setup, press and hold the button on the control panel for approximately 5

seconds. Once the display timer counter reaches the count of 5, release the button.

8. The blinking open door icon is displayed first on the control panel screen. Press the button to

move through different options.

When the transmission icon shows on the display, stop pressing the button - the transmission

icon will begin blinking. This indicates the opener is ready to recognize the universal remote.

9. Press the button you prepared on the universal remote one time –the transmission icon will stop

blinking and change to a solid icon. This indicates the remote has been successfully recognized by the

opener.

10. Press the button to save the entry and end the system setup. Press and release the remote

button one time. The opener should run. The display will look like this after setup is completed:

transmission icon

Available in remotes with software REVs v1.1.8 and lower (also allows FAAC receiver compatibility)

Inhaltsverzeichnis

Andere Genie Fernbedienung Handbücher

Genie

Genie 3 Button Remote Bedienungsanleitung

Genie

Genie Confirm Betriebsanleitung

Genie

Genie UNIVERSAL REMOTE Bedienungsanleitung

Genie

Genie GT912-BX Bedienungsanleitung

Genie

Genie INTELLICODE GITR-3BX Bedienungsanleitung

Genie

Genie UNIVERSAL REMOTE Bedienungsanleitung

Genie

Genie Confirm Betriebsanleitung

Genie

Genie Series III Bedienungsanleitung

Genie

Genie Remote Control Bedienungsanleitung

Genie

Genie ACSCTG-UNIV2 Bedienungsanleitung

Genie

Genie QN-RS283 Fehlerbehebungshandbuch

Genie

Genie 3 Button Remote Bedienungsanleitung

Genie

Genie GIT-1 Bedienungsanleitung

Genie

Genie G3T-BX Installationshandbuch

Beliebte Fernbedienung Handbücher anderer Marken

Panasonic

Panasonic EUR7622KB0 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen Beo4 Bedienungsanleitung

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung

Multiplex

Multiplex PROFI TX 9 Bedienungsanleitung

One Remote

One Remote RMB4 Bedienungsanleitung

FUTABA

FUTABA 9ZAP - PART2 Bedienungsanleitung

HR Matic

HR Matic HR MULTI 3 Bedienungsanleitung

Yamaha

Yamaha ACC-GNRST-30-20 Bedienungsanleitung

EisSound

EisSound KBSOUND Bedienungsanleitung

Marantz

Marantz RC101 Bedienungsanleitung

Conrad

Conrad FS20 TC6 Bedienungsanleitung

Anritsu

Anritsu MP1777A Bedienungsanleitung

Niles

Niles WVC100 Fehlerbehebungshandbuch

RCA

RCA RCU1300 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BEO6 Bedienungsanleitung

GE 94901 Bedienungsanleitung

Onbon

Onbon YQ1-75 Bedienungsanleitung

FUTABA

FUTABA R7108SB Montageanleitung