Gentner ET10 Bedienungsanleitung
E
T10
Teleconferencer
User’s Manual
Copyright 1996 by Gentner Communications Corporation. All rights reserved. No part of
this manual may be reproduced in any form or by any means without written permission from
Gentner Communications Corporation. Printed in the United States of America. Original
version, 1/96. Gentner Communications Corporation reserves specification privileges.
Information in this manual is subject to change without notice.
Copyright
Information
The ET10 is designed for workstations and small conference
rooms. For medium and large conference rooms, contact
Gentner Communications Corporation for assistance.
ForSetupAssistanceDial: 800-945-7730or801-975-7200
ET10 User’s Manual Page 1
Congratulations on purchasing the teleconferencing
industry’s first full-duplex audioconferencer
designed for analog or digital telephones. The ET10
teleconferencer allows you to hold a completely
interactive teleconferencing meeting at your work
station, as long as the keypad is not in the handset
itself. With the ET10, you can directly connect to
your existing telephone to maintain all of your
telephone functions.
This manual explains how to install, set up and
operate the ET10 and the optional ET10ex extension
microphone step by step. It also provides instruc-
tions on how to improve room acoustics and resolve
minor technical problems, should any arise.
If you need additional information on how to install,
set up or operate your system, please contact us at
Gentner Communications Corporation at the
location noted below. We welcome and encourage
your comments so we can continue to improve our
products and serve your teleconferencing needs.
Gentner Communications Corporation
1825 Research Way
Salt Lake City, UT 84119
TEL: Worldwide (801) 975-7200 In U.S.A. (800) 945-7730
FAX: Worldwide (801) 977-0087 In U.S.A. (800) 933-5107
Introduction
ForSetupAssistanceDial: 800-945-7730or801-975-7200
Page 2 ET10 User’s Manual
Ensure that the following equipment was received
with your shipment:
SHIPPING NOTE:
Gentner Communications is not responsible for
product damage incurred during shipment. You
must make claims directly with the carrier. Inspect
your shipment carefully for obvious signs of
damage. If the shipment appears to be damaged,
retain the original boxes and packing material for
inspection by the carrier. Contact your carrier
immediately.
Unpacking
15’ Ex Cable Assembly *
DirectPlug-InPower
Module
ET10exMicrophone*
Optional accessories
* Additional accessories available
(back cover). Contact Gentner
Communications Corporation for
more information.
ET10 Manual
13" Flat Handset Cable
ET10
ForSetupAssistanceDial: 800-945-7730or801-975-7200
ET10 User’s Manual Page 3
Turns your existing telephone into a full-duplex
audioconferencer
Provides telephone compatibility to use your current
telephone capabilities (i.e. hold, transfer, confer-
ence, speed-dial, last-number redial, etc.)
Operates with digital and analog telephones
Functions without installation of a dedicated
telephone line
Allows full-duplex operation for participants to talk
and listen without speakerphone cutoffs
Maximizes isolation between speaker and
microphones for enhanced audio quality
Utilizes unsurpassed digital technology for audio
quality
Provides 120opick-up pattern with built-in profes-
sional microphone
Uses simple mute and volume controls
Records audioconference through tape recorder jack
Installs and operates easily
Provides access to professional technical support for
reliable assistance with setup and operation
Expands capabilities with the optional ET10ex
extension microphone
Allows optional headset port for private, hands-free
communication
Indicates when unit is properly adjusted with
assisted setup
Features and
Benefits
ForSetupAssistanceDial: 800-945-7730or801-975-7200
Page 4 ET10 User’s Manual
The ET10 is designed to work in almost any
acoustic environment with digital and analog
telephones. This unique design is a first in the
audioconferencing industry. To maximize your
teleconference audio quality, we recommend that
you prepare your teleconferencing site by taking the
following factors into consideration:
Acoustic Room Treatment
Rooms that have large areas of windows, white
boards, hard floors, etc., are acoustically “live.”
These areas increase the amount of audio
reverberation in the room which, in turn,
reduces the audio quality of your
teleconference. You should minimize the
amount of audio reverberation where possible.
You can improve room acoustics by installing
acoustic panels, drapes and other wall fabrics.
Another way to improve overall room acoustics
is to keep room noise, such as computers and
fans, to a minimum.
Power Requirements
The ET10 will accommodate voltage
requirements in accordance with the supplied
direct plug-in power module.
Telephone Line Requirements
Unlike other portable full-duplex
audioconferencing units, the ET10 connects
directly to digital and analog telephones. A
dedicated analog telephone line is NOT needed
to operate your ET10.
Before You
Install
ForSetupAssistanceDial: 800-945-7730or801-975-7200
ET10 User’s Manual Page 5
Telephone Set Requirements
The ET10 will operate with telephone sets that
have a detachable handset cord at the telephone
base. The ET10 will not work with “Princess”
or “Trimline” style telephones that have the dial
pad built into the handset. The dial pad must be
located on the telephone base, not on the
telephone handset.
Equipment Placement
Place the ET10 next to the telephone set.
ForSetupAssistanceDial: 800-945-7730or801-975-7200
Page 6 ET10 User’s Manual
The ET10 connects directly to your existing
telephone set so that you can maintain all your
standard telephone functions. Follow these step-by-
step instructions to install your ET10:
Completed Installation
The following drawing diagrams the ET10
system when installation is complete.
Step 1
Unplug the handset cord from the base of
your telephone set. Plug the handset cord
into the ET10 module jack labeled .
Installation
HandsetModuleJack
ForSetupAssistanceDial: 800-945-7730or801-975-7200
ET10 User’s Manual Page 7
Step 2
Plug one end of the supplied 13-inch handset
cable into the telephone handset jack. Plug the
other end of the flat handset cable into the ET10
jack labeled . Note: If you need a longer
handset cable, please contact Gentner
Communications at the number listed below.
Step 3 (ET10ex Option)
If using the ET10ex, plug the external
microphone into the port labeled EXT MIC.
Both internal and external mics will operate at
the same time. Note: If the external
microphone is not in use, unplug it to prevent
possible reverb distortion
TelephoneModuleJack
ExternalMicrophonePort
ForSetupAssistanceDial: 800-945-7730or801-975-7200
Page 8 ET10 User’s Manual
Step 4
Plug in the direct plug-in power adaptor barrel
connector into the ET10 power connector
labeled 12 VDC.
Step 5 (Record Option)
To record your audioconference, connect a tape
recorder (not provided) to the ET10 jack labeled
REC. A standard phono cable is typically
supplied with most tape recorders, or may be
purchased at most electronic supply stores.
PowerConnector
TapeRecorderJack
Inhaltsverzeichnis
Andere Gentner Konferenzsystem Handbücher
Gentner
Gentner ET100 Bedienungsanleitung
Gentner
Gentner XAP 800 Kurzanleitung
Gentner
Gentner XAP 800 Bedienungsanleitung
Gentner
Gentner TI7200 Bedienungsanleitung
Gentner
Gentner Audio Perfect 800 Bedienungsanleitung
Gentner
Gentner GT300 Bedienungsanleitung
Gentner
Gentner Audio Perfect Video 200 Bedienungsanleitung
Gentner
Gentner Audio Perfect 400 Bedienungsanleitung
Gentner
Gentner XAP 800 Bedienungsanleitung
Beliebte Konferenzsystem Handbücher anderer Marken
Kramer
Kramer VIA GO Bedienungsanleitung
AVT
AVT MAGIC AC1 Go Bedienungsanleitung
ProSoft Technology
ProSoft Technology AN-X4-AB-DHRIO Bedienungsanleitung
Sony
Sony PCS-I150 Bedienungsanleitung
Middle Atlantic Products
Middle Atlantic Products VTC Series Bedienungsanleitung
Prentke Romich Company
Prentke Romich Company Vanguard Plus Leitfaden
