Geokon GeoNet 8000 Series Bedienungsanleitung

Installing Model 8920

Cellular Loggers

GEOKON Provided

►Mini to standard USB cable

►#3 Philips head screwdriver

►Small flat head screwdriver

►Desiccant packs

Customer Provided

►Mounting hardware

►Materials to create a suitable earth ground

Items Required for Installation

1. Remove the rubber cap from

the antenna mount

2. Thread the antenna onto the

mount by rotating it clockwise

until finger tight

Attach the Antenna

Do not cross thread the antenna.

The O-ring on the antenna must

be flush against the enclosure.

C D

Cellular Loggers can be mounted

using bolts (A), screws (B),

hose clamps (C), U-bolts (D), etc.

(Mounting hardware not included)

Always mount Loggers vertically,

with the antenna pointing up

The space around the antenna

should be free of obstructions

A minimum mounting height of

two meters (six-feet) is

recommended

Logger Mounting

The direction of tilt for the A and

B axes is shown on the cover of

the unit

The two axes of the tiltmeter

have a calibrated range of ±30°,

based on a starting position of 0°

(antenna pointing up)

Tiltmeter Logger Orientation

Properly grounding Loggers

protects against lightning and

other large transient voltages

A 6-foot copper rod and 12

AWG or larger copper wire

are recommended

All Cellular Loggers can be

grounded via the mounting

bracket (A)

Multi-channel Loggers can

also be grounded via the

copper ground lug on the

bottom of the enclosure (B)

Grounding the Logger

A B

1. Using a Phillips head screwdriver,

loosen the cover screws by turning

them counterclockwise

2. Remove the cover

Remove the Cover

1. Record the serial number of the

sensor and the logger

(For Multi-channel loggers, note

the channel each sensor has

been wired into)

2. Loosen the cable gland nut and

remove white plastic dowel

3. Slide the cable of the sensor

through the cable gland (and

gland nut) and into the Logger

Connecting the Sensor

4. Wire each conductor by

pressing down on an orange

tab, inserting the bare end of

the conductor into the terminal

block, then releasing the tab

Conductors are wired as

follows:

Connect the Sensor (Continued)

Addressable Loggers

GREEN = 485–

RED = 12V

BLACK = GND

VW Loggers

RED =

BLACK = VW–

GREEN = TH–

5. Gently pull on each conductor to make sure it is secure

6. Tighten the nut onto the cable gland until the gland firmly grips

the outer jacket of the cable

The cable gland must be properly tightened to prevent water

entry (Do not over-tighten, which may strip the plastic threads)

7. Gently pull on the sensor cable to make sure it is held in place

by the cable gland

Connect the Sensor (Continued)

To prevent possible short circuits, do not allow bare leads to

touch each other during or after wiring

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Geokon Datenlogger Handbücher

Geokon

Geokon 8800 Bedienungsanleitung

Geokon

Geokon GeoNet 8900 Series Bedienungsanleitung

Geokon

Geokon LC-2 Bedienungsanleitung

Geokon

Geokon GeoNet 8900 Series Bedienungsanleitung

Geokon

Geokon GeoNet 8900 Series Bedienungsanleitung

Geokon

Geokon 8800 Bedienungsanleitung

Geokon

Geokon GK-404 Bedienungsanleitung

Beliebte Datenlogger Handbücher anderer Marken

TESTO

TESTO 176 Bedienungsanleitung

HBM

HBM SOMAT XR CX22B-R Bedienungsanleitung

Agtrix

Agtrix 380i Bedienungsanleitung

Hobo

Hobo H8 Pro Bedienungsanleitung

Beijing ART Tech

Beijing ART Tech PCI2320 Bedienungsanleitung

Athena

Athena GET SL1 Bedienungsanleitung

Motec Systems

Motec Systems C185 Bedienungsanleitung

Beijing ART Tech

Beijing ART Tech USB2832 Bedienungsanleitung

HT Italia

HT Italia XL421 Bedienungsanleitung

Rotronic

Rotronic HygroLog HL20 Bedienungsanleitung

MRC

MRC DW-6092 Bedienungsanleitung

Racelogic

Racelogic VBOX LapTimer Bedienungsanleitung

Edu-Logger

Edu-Logger 900-240 Bedienungsanleitung

Elma

Elma DT173 Bedienungsanleitung

MadgeTech

MadgeTech PRTemp140 Technisches Datenblatt

Comet

Comet U0121M Bedienungsanleitung

pico Technology

pico Technology PT-104 Bedienungsanleitung

Soil Instruments

Soil Instruments GTecLink Bedienungsanleitung