GeoVision GV-POE0410-E Bedienungsanleitung
GV-POE0410-E User's Manual
GV-PoE Switch
POE0410E-B
Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use.
© 2016 GeoVision, Inc. All rights reserved.
Under the copyright laws, this manual may not be copied, in whole or in part,
without the written consent of GeoVision.
Every effort has been made to ensure that the information in this manual is
accurate. GeoVision, Inc. makes no expressed or implied warranty of any kind
and assumes no responsibility for errors or omissions. No liability is assumed
for incidental or consequential damages arising from the use of the information
or products contained herein. Features and specifications are subject to
change without notice.
GeoVision, Inc.
9F, No. 246, Sec. 1, Neihu Rd.,
Neihu District, Taipei, Taiwan
Tel: +886-2-8797-8377
Fax: +886-2-8797-8335
http://www.geovision.com.tw
Trademarks used in this manual: GeoVision, the GeoVision logo and GV
series products are trademarks of GeoVision, Inc. Windows is the registered
trademark of Microsoft Corporation.
July 2016
2
3
Contents
Contents.................................................................................................................... 2
1. Safety Precautions ................................................................................................ 1
2. Introduction ...........................................................................................................
2.1. Key Features ......................................................................................
2.2. Packing List ........................................................................................ 3
3
4
7
8
8
9
10
11
12
2.3. Option .................................................................................................
3. Hardware Description............................................................................................
4. DIN-Rail Mounting .................................................................................................
5. Hardware Installation.............................................................................................
5.1. Wiring the DC Power Inputs ................................................................
5.2. Wiring the Alarm Relay........................................................................
5.3. Wiring the Earth Grounding...............................................................
5.4. Enable the Event Alarm Function .......................................................
5.5. Cabling .............................................................................................
1. Safety Precautions
FCC Warning
This Equipment has been tested and found to comply with the limits for a Class-A
digital device, pursuant to Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy. It may cause harmful interference to radio communications if the equipment
is not installed and used in accordance with the instructions. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
yReorient or relocate the receiving antenna.
yIncrease the separation between the equipment and receiver.
yConnect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
yConsult the dealer or an experienced radio/TV technician for help.
1
2. Introduction
Figure 2-1
Product Overview
The GV-POE0410-E is a 4-port PoE Switch with 4 PoE+ 10/100/1000BaseT(X) port
and 1 Gigabit SFP. The switch supports IEEE 802.3at Power over Ethernet standard
with up to 30 W per port and maximum 130 W power consumption per system. No
special network cable is required for connecting your powered devices (PD), such as
IP cameras. The GV-POE0410-E is featured with a redundant power supply for
automatic power backup and supports alarms alerting for power and link failure.
The switch is designed for small network environment to strengthen its network
connection and efficiency.
Redundant Power Inputs
This switch provides two power inputs that can be connected simultaneously as
power supply. One of the power supplies provides backup power immediately if the
other fails.
Auto-Negotiation
Every port can automatically detect and adjust if the connected network devices are
running at 10Mbps, 100M, 1000Mbps and Half/Full-Duplex mode.
Auto-MDI/MDI-X
Every port can automatically detect your type of cable. There is no need for
crossover cables whether you are connecting this switch to another switch or to a
computer.
Rugged Design
This switch is designed for harsh environmental conditions. With its rigid aluminum
enclosure and 6kV surge protection design, the switch not only protects the surge
from the DC in port, but also the RJ-45 ports. By using this switch, it will make your
network more reliable regardless of the bad weather outside.
2
2.1. Key Features
•4-port PoE+ 10/100/1000BaseT(X), 1 Gigabit SFP
•IEEE 802.3at Compliant (4 Ports at Full 30W)
•Max. 130 W power consumption
•Extreme temperature support (40°C ~ 70°C /40°F ~ 158°F)
•Auto-MDI/MDI-X
•Auto-Negotiation
•Alarm control
•DIN-Rail Installation
•Redundant DC power
•6 kV surge protection
•Up to 4 GV-IP Cameras support
2.2. Packing List
1. GV-POE0410-E x 1
2. GV-POE0410-E Quick Start Guide x 1
2.3. Option
Optional devices can expand your GV-POE0410-E’s capabilities and versatility.
Contact your dealer for more information.
GV-LC and GV-LC10
The SFP Transceiver is designed to plug into the SFP
port of the GV-POE Switch and is the interface between
the switch and optical fiber cables. This product complies
with IEEE 802.3z 1000BaseSX/LX standards. The SFP
Transceiver is a hot swappable device; you can add or
remove the device without powering down.
3
3. Hardware Description
This section mainly describes the hardware of this switch and gives a physical and
functional overview on the switch.
Dimensions
The dimensions of this switch are 120 x 55 x 108 mm (4.72” x 2.16” x 4.25”).
Figure 3-1
4
Front Panel
4 PoE ports / LED
Gigabit SFP port / LED
Alarm Control / LED
Power 1 ~ 2
Figure 3-2
LED Status Description
Green on Power onPWR1
Off Power off
Green on Power onPWR2
Off Power off
Red on Port link down or power failureAlm
Off No event
Green On A network device is detected and links upPort 1~4
Yellow On A powered device is detected and links up
Port 5 (SFP) Green on The gigabit SFP port links up
Note: If the power LEDs go off when the power cord is plugged in, a power failure
might have occurred. Check the power output connection to see if there is any error
at the power source. If you still cannot solve the problem, contact your local dealer
for assistance.
5
Bottom Panel
Dip Switch for
Alarm Control
Removable
Terminal Block
Earth Ground Screw
Figure 3-3
The GV-POE0410-E is featured with a redundant power supply for automatic power
backup and supports alarms alerting for power and link failure.
Power Supply
With DC power cables wired to both PW1 and PW2 on the terminal block, one of the
power supplies provides backup power immediately if the other fails.
Alarm Control
With an alarm device wired to Alm on the terminal block, when any of the power
supplies fails or any of the port links fails, the alarm will be triggered. Use the dip
switch to enable or disable the alarm function.
Power 1 Connect to DC power input
Power 2 Connect to DC power input
Terminal
Block
Alarm control Connect to an alarm output
Switch 1 ~ 5 Switch up/down to turn on/off the alarm of
corresponding port links on the front panel.
Dip switch 1 ~ 4 corresponds to Port 1 ~ 4, and dip
switch 5 corresponds to Port 5 (SFP) on the front
panel.
Dip Switch
Switch 6 Switch up/down to enable/disable the alarm for
power failure.
6
4. DIN-Rail Mounting
A DIN-Rail clip is built in the rear body of the switch supporting EN 50022 standard
DIN Rail. The dimensions of EN 50022 DIN Rail are included in the following
diagram. Follow the steps below to mount the switch on a DIN-Rail track.
1. Insert the upper end of the DIN-Rail clip into the back of the DIN-Rail track
from its upper side
2. Lightly push the bottom of the DIN-Rail clip into the track.
3. Check if the DIN-Rail clip is tightly attached to the track.
4. To remove the switch from the track, reverse the steps above.
Figure 4-1
7
Inhaltsverzeichnis
Andere GeoVision Schalten Handbücher
GeoVision
GeoVision GV-APOE0810 Bedienungsanleitung
GeoVision
GeoVision GV-POE2411-V2 Bedienungsanleitung
GeoVision
GeoVision GV-APOE0410-E Bedienungsanleitung
GeoVision
GeoVision GV-POE0811-V2 Bedienungsanleitung
GeoVision
GeoVision GV-APOE0400 Bedienungsanleitung
GeoVision
GeoVision GV-APOE0400 Bedienungsanleitung
GeoVision
GeoVision GV-POE0801 Bedienungsanleitung
GeoVision
GeoVision GV-APOE4813 Bedienungsanleitung
GeoVision
GeoVision GV-POE2411 Bedienungsanleitung
GeoVision
GeoVision GV-POE0800 Bedienungsanleitung
GeoVision
GeoVision GV-APOE4813 Bedienungsanleitung
GeoVision
GeoVision GV-POE2401-V2 Bedienungsanleitung
GeoVision
GeoVision GV-POE0410-E-V2 Bedienungsanleitung
GeoVision
GeoVision GV-POE1611 Bedienungsanleitung
GeoVision
GeoVision GV-POE2411 Bedienungsanleitung
GeoVision
GeoVision GV-APOE0811 Bedienungsanleitung
GeoVision
GeoVision GV-PoE Bedienungsanleitung
GeoVision
GeoVision GV-POE1611-V2 Bedienungsanleitung
GeoVision
GeoVision GV-POE0812 Bedienungsanleitung
GeoVision
GeoVision GV-APOE4813 Bedienungsanleitung
