Gericom LA750 Bedienungsanleitung

17” TFT

LCD TV / MONITOR

INSTRUCTION MANUAL

BEDIENUNGSLEITUNG

1INSTRUCTION MANUAL

CONTENTS

SAFETY INSTRUCTION 2

CAUTIONS 4

FCC RF INTERFERENCE STATEMENT 5

CONNECTING WITH EXTERNAL EQUIPMENT 6

RESOLUTION 8

CONTROLS AND FUNCTIONS 9

REMOTE FUNCTIONS 19

REAR VIEW 20

STAND SLOPE 21

D-SUB CONNECTOR PIN ASSIGNMENTS 22

POWER MANAGEMENT 23

SPECIFICATIONS 24

TROUBLESHOOTING GUIDE 25

WICHTIGE HINWEISE (GERMAN) 26

INSTRUCTION MANUAL 2

SAFETY INSTRUCTION

1. Read all of these instructions.

2. Save these instructions for later use.

3. Follow all warnings and instructions marked on the product.

4. Unplug this product from the wall outlet before cleaning.

Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

5. Do not use this product near water.

6. Do not place this product on an unstable cart, stand or table.

The product may fall, causing serious damage to the product.

7. Slots and openings in the cabinet and the back are provided for

ventilation: to ensure reliable operation of the product, these openings

must not be blocked by placing the product on a bed, sofa, rug or

other similar surface.

This product should never be placed near or over a heat register.

This product should not be placed in a built-in installation unless proper ventilation

is provided.

8. This product should be operated from the type of power source indicated on the

marking label. If you are not sure of the type of power available, consult your dealer

or local power company.

9. This product is equipped with a 3 wire grounding type plug having a third(grounding)

pin. This is a safety feature. If you are unable to insert the plug into the outlet,

contact your electrician to replace your obsolete outlet. Do not defeat the purpose of

the grounding-type plug.

10. Do not allow anything to rest on the power cord.

Do not locate this product where persons will walk on the cord.

11. If an extension cord is used with this product, make sure that the total of the

ampere ratings on the products plugged into the extension cord do not exceed the

extension cord ampere rating. Also, make sure that the total of all products

plugged into the wall outlet does not exceed 10 amperes.

12. Never push objects of any kind into this product through cabinet slots as they may

touch dangerous voltage points or short out parts that could result in a risk of fire

or electric shock. Never spill any kind of liquid on the product.

13. Do not attempt to service this product yourself, as opening or removing covers

may expose you to dangerous voltage points or other risks.

Refer all servicing to service personnel.

3INSTRUCTION MANUAL

SAFETY INSTRUCTION

14. Unplug this product from the wall outlet and refer servicing to qualified service

personnel under the following conditions.

A. When the power cord or plug is damaged or frayed.

B. If liquid has been spilled into the product.

C. If the product has been exposed to rain or water.

D. If the Product does not operate normally when the operating instructions are

followed. Adjust only those controls that are covered by the operating

instructions since improper adjustment of other controls may result in damage

and will often require extensive work by a qualified technician to restore normal

operation.

E. If the product has been dropped or the cabinet has been damaged.

F. If the product exhibits a distinct change in performance, indicating a need for

service.

The power supply cord is used as the main disconnect device, ensure that the

socket-outlet is located/installed near the equipment and is easily accessible.

Le cordon d`alimentation est utillsé comme interrupteur général. La prise de

courant doit être située ou installée à proximité du matériel et être facile

d`accès

CAUTION TO SERVICE PERSONNEL

POWER SUPPLY CORD IS USED AS MAIN POWER DISCONNECT DEVICE IN

THIS PRODUCT. UNPLUG THIS PRODUCT FROM THE WALL OUTLET

BEFORE REMOVING THE BACK COVER AND SERVICING

EMISSION CHARACTERISTICS TESTED BY SEMKO

THIS PRODUCT HAS BEEN TESTED AND HAS SHOWN COMPLIANCE WITH

THE NATIONAL SPECIFICATIONS SUCH AS SWEDISH MPR 1990.10.(MPR )

INSTRUCTION MANUAL 4

CAUTIONS

NEVER REMOVE THE BACK COVER

Removal of the back cover should be carried out only by qualified personnel.

DO NOT USE IN HOSTILE ENVIRONMENTS

To prevent shock or fire hazard, do not expose the unit to rain or moisture.

This unit is designed to be used in the office or home. Do not subject the unit to

vibrations, dust of corrosive gases.

KEEP IN A WELL VENTILATED PLACE

Ventilation holes are provided on the cabinet to prevent the temperature from

rising.

Do not cover the unit or place anything on the top of unit.

AVOID HEAT

Avoid placing the unit in direct sunshine or near a heating appliance.

TO ELIMINATE EYE FATIGUE

Do not use the unit against a bright back ground and where sunlight or other light

sources will shine directly on the monitor.

BE CAREFUL OF HEAVY OBJECT

Neither the monitor itself nor any other heavy object should rest on the power cord.

Damage to a power cord can cause fire or electrical shock.

5INSTRUCTION MANUAL

FCC RF

INTERFERENCE STATEMENT

This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a

residential installation.

This equipment generates, uses and can radiate radio frequency energy and,

if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee

that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television

reception which can be determined by turning the equipment off and on, the user

is encouraged to try to correct the interference by one or more of the following

measures.

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which

the receiver is connected.

- Consult the dealer or an experienced radio, TV technician for help.

- Only shielded interface cable should be used.

Finally, any changes or modifications to the equipment by the user not

expressly approved by the grantee or manufacturer could void the users

authority to operate such equipment.

DOC COMPLIANCE NOTICE

This digital apparatus does not exceed the Class B limits for radio noise emissions

from digital apparatus set out in the radio interference regulation of Canadian

Department of Communications.

AVIS DE CONFORMATION AU MDC(DOC)

Le presént appareil numérique n`émet pas de bruits radio-électriques dépassant les

limites appliqués aux appareils numériques de Class B d´arès les règlement sur le

brouillage radio-électrique conçuent par le ministère des communications du

Canada.

INSTRUCTION MANUAL 6

CONNECTING WITH EXTERNAL

EQUIPMENT

Be sure to turn off the power of your computer before connecting the monitor.

1. CONNECT THE VIDEO SIGNAL CABLE

A. Connect one end of the signal cable to the back panel of the monitor

and connect the other end to the graphic card on back of the computer.

B. Secure the connection with the screws on the plug.

2. CONNECT THE POWER CORD

Connect the female end of the power cord to the power input

receptacle on the LCD Monitor.

Then, plug the male end of the power cord to an AC outlet or computer.

3. CONNECT THE A/V CABLE

A. Connect the end of RCA(Yellow, White, Red) SCART or S-VHS cable to

the terminals on the back of the Monitor.

B. Connect an antenna or CATV cable to the terminal on the back of the Monitor.

(Optional TV Tuner can be purchased from the dealer)

C. Connect one end of stereo audio cable to the stereo jack on the back of the Monitor.

(Connect another end of stereo audio cable to the “Audio(Line) out” terminal of

the sound card on your computer or another audio equipment)

4. TURN THIS MONITOR ON AND START YOUR SYSTEM

7INSTRUCTION MANUAL

5. CONNECT THE TUNER(OPTION)

Be sure to turn off the power of your monitor before connecting the tuner.

A. Open the cover.

B. Insert the Tuner and close the cover.

A. Do not disassemble the tuner after proper Installation.

B. Do not pull the antenna terminal only. This terminal is easy to break.

CONNECTING WITH EXTERNAL

EQUIPMENT

9INSTRUCTION MANUAL

CONTROLS AND FUNCTIONS

B. SOURCE BUTTON

E. VOLUME BUTTONS

(LEFT & RIGHT)

D. CHANNEL BUTTONS

(DOWN & UP)

POWER INDICATOR(LED)

A. POWER SWITCH

A. POWER ON/OFF( )

Turns the power ON or OFF. There will be a few seconds delay before the

display appears.

The power LED(next to the power switch) lights with green when the power is turned ON.

The power is turned off by pressing the power switch again and the power

LED goes Red.

B. SOURCE ( )

Change input Source one by one

(PC, VIDEO, S-VIDEO, TV, SCART)

C. MENU ( )

Activates and exits the On Screen Display.

This button can also be used to move previous menu or status.

OSD MENU(MAIN) : Input Source, Screen, Audio, OSD, Color, Utility, Exit.

REMOCON SENSOR

C. MENU BUTTON

Inhaltsverzeichnis

Sprachen:

Andere Gericom Monitor Handbücher

Gericom

Gericom GTV3203 Bedienungsanleitung

Beliebte Monitor Handbücher anderer Marken

Linear Acoustic

Linear Acoustic LQ-1000 Bedienungsanleitung

AOC

AOC I2579V Bedienungsanleitung

Gateway

Gateway FPD1520 Bedienungsanleitung

Furuno

Furuno Mu 120c Bedienungsanleitung

Asus

Asus VB171D - 17" LCD Monitor Bedienungsanleitung

Dell

Dell S2230MX Gebrauchsanweisung

Philips

Philips 107C64 Bedienungsanleitung

Dell

Dell S2409WFP Bedienungsanleitung

EverFocus

EverFocus EN-7517E Bedienungsanleitung

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Bedienungsanleitung

Dell

Dell Precision 7680 Bedienungsanleitung

LG 50PM1M - - 50" Plasma Panel Bedienungsanleitung

Bosch

Bosch DDU 9 Bedienungsanleitung

Acer

Acer A231HL Bedienungsanleitung

Philips

Philips 86BDL4152T Bedienungsanleitung

NEC

NEC AccuSync LCD5V Bedienungsanleitung

Emay

Emay SleepO2 Bedienungsanleitung

IBM

IBM 6360 Montageanleitung