Gestetner P7675 Bedienungsanleitung

DataOverwriteSecurity Unit Type E

DataOverwriteSecurity Unit Type G

Operating Instructions

For security, please read this manual carefully before you use this product and keep it handy for future reference.

Introduction

This manual contains detailed instructions and notes on the operation and use of this product. For your

safety and benefit, read this manual carefully before using the product. Keep this manual in a handy

place for quick reference.

Important

Contents of this manual are subject to change without prior notice. In no event will the company be li-

able for direct, indirect, special, incidental, or consequential damages as a result of handling or oper-

ating the machine.

Some illustrations in this manual might be slightly different from the machine.

Depending on your machine, the panel display may differ slightly.

Conditions for Use

To function effectively, this option requires the following conditions.

Operating Environment

• The machine is operating normally and is not damaged, modified, or lacking

components.

• The machine is managed by a administrator who has carefully read and un-

derstood the manual for this option, and can ensure its safe and effective us-

age by general users.

Note

❒Customer engineers dispatched from the supplier or its affiliated companies

are trained in the maintenance of this option.

Precautions When Using the DataOverwriteSecurity Unit

The procedures in this manual should be performed by the machine administra-

tor. For details, see Security Guide or Note to Administrator.

*1 For details on the Data Erase Status, see p.10 “Data Erase Status”.

• If the printer enters Energy Saver mode when overwriting is in progress,

press the any key to revive the display in order to check the [Memory Erase Sta-

tus]or [Mem. Erase Info]menu.

•IfDataEraseStatusshows“

Data to erase remaining.”even after you

have checked there is no temporary data, turn off the machine’s main power

switch. Wait a few moments, turn it back on, and then check if Data Erase Sta-

tus shows “Currently no data to erase.”. If it does not, contact your sales

or service representative.

•If Data Erase Status is not displayed, first check the optional DataOverwriteSecurity

Unit is installed. If the optional DataOverwriteSecurity Unit is installed but Data Erase

Status still does not appear, contact your service representative. *1

•If you turn off the machine’s main power switch before overwriting is completed, tem-

porary data will remain on the hard disk until the main power switch is next turned on

and overwriting is resumed.

Description for the Specified Model

This manual uses the following items to explain about the printer according to

the specified model.

For 4 line display model:

This explains about the 4 line display model. You can identify your model using

the following display on the printer.

Read this if you have this model.

For 2 line display model:

This explains about the 2 line display model printer. You can identify your mod-

el using the following display on the printer.

Read this if you have this model.

Displaying administrator menus

For 2 line display model, you can display the administrator menus by using spe-

cific key combinations on the control panel of the printer.

This section describes how to display the administrator menus.

ACheck the printer is online.

BPress the {qEnter}key, press the {Escape}key, and then press the {Menu}key.

The menu screen appears.

CPress the {U} or {T} key to display [Maintenance], and then press the {qEn-

ter}key.

DPress the {U} or {T} key to check the administrator menus including [Mem-

ory Erase]and [Erase All Mem.]are displayed.

You can now display the administrator menus and make any necessary

changes to the settings.

EPress the {Online}key after completing all the required settings.

The initial screen appears, preventing you from displaying the administrator

menus. To display the administrator menus again, repeat the procedures

from the start.

Deleting Data on the Hard Disk

To use this function, the optional DataOverwriteSecurity Unit must be installed.

To prevent data on the hard disk being leaked before disposing of the printer,

you can overwrite all data stored on the hard disk. You can also automatically

overwrite temporarily-stored data.

❖Auto Erase Memory Setting

To erase selected data on the hard disk, specify [Auto Erase Memory Setting].

❖Erase All Memory

To erase all the data on the hard disk, using [Erase All Memory].

❖Methods of Erasing the Data

You can select the method of erasing the data from the following:

The default is “NSA”.

*1 National Security Agency

*2 Department of Defense

Note

❒Depending on the hard disk capacity and the method of erasing the data, this

action may take a few hours. Once you start the Erase All Memory function,

no other printer operation is possible until the function completes or you quit

the function.

❒The printer’s hard disk lets you store data under the printer.

NSA

Overwrites the data on the hard disk twice with random numbers

and once with zeros.

DoD

Overwrites the data with a number, its complement, and random

numbers, and then checks the result.

Random Numbers Overwrites the data with random numbers the specified number of

times.

You can specify between 1 and 9 as the number of times the data is

overwritten with random numbers. The default is 3 times.

Auto Erase Memory Setting

This can be specified by the machine administrator.

A print data sent from a printer driver is temporarily stored on the printer's hard

disk.

Even after the job is completed, it remains in the hard disk as temporary data.

Auto Erase Memory erases the temporary data on the hard disk by writing over it.

Overwriting starts automatically once the job is completed.

The Printer functions take priority over the Auto Erase Memory function. If a

print job is in progress, overwriting will only be done after the job is completed.

Preparation

If you have the 2 line display model, make sure that the administrator menus

are displayed before performing the operation. See p.2 “Displaying adminis-

trator menus”.

For details about logging on and logging off with administrator authentica-

tion, see Security Guide or Note to Administrator.

For 4 line display model:

APress the {Menu}key.

BSelect [Security Options]using the {U} or {T} key, and then press the {OK}key.

CSelect [Auto Erase Memory Setting]using the {U} or {T} key, and then press

the {OK}key.

DSelect [On]using the {U} or {T} key, and then press [HD Erase].

Select the method of erasing the data from [NSA], [DoD], or [Random Numbers].

If you select [Random Numbers], proceed to step E.

If you select [NSA]proceed to step G.

If you select [DoD], proceed to step H.

ESelect [Random Numbers]using the {U} or {T} key, and then press the {OK}key.

FEnter the number of times that you want to overwrite using the {U} or {T}

keys, and then press the {OK}key.

Auto Erase Memory is set.

GSelect [NSA]using the {U} or {T} key, and then press the {OK}key.

Auto Erase Memory is set.

HSelect [DoD]using the {U} or {T} key, and then press the {OK}key.

Auto Erase Memory is set.

For 2 line display model:

APress the {Menu}key.

BSelect [Maintenance]using the {U} or {T} key, and then press the {qEnter}key.

CSelect [Memory Erase]using the {U} or {T} key, and then press the {qEnter}key.

DSelect [Auto Erase]using the {U} or {T} key, and then press the {qEnter}key.

ESelect [On]using the {U} or {T} key, and then press the {qEnter}key.

After the settings are made, about two seconds later, the screen return to the

Memory Erase setup menu.

FSelect [Erase Method]using the {U} or {T} key, and then press the {qEnter}key.

GSelect the method of erasing the data.

Select the method of erasing the data from [NSA], [DoD], or [Random].

If you select [Random], proceed to step H.

If you select [NSA]proceed to step J.

If you select [DoD], proceed to step K.

HSelect [Random]using the {U} or {T} key, and then press the {qEnter}key.

IEnter the number of times that you want to overwrite using the {U} or {T}

keys, and then press the {qEnter}key.

Auto Erase Memory is set.

JSelect [NSA]using the {U} or {T} key, and then press the {qEnter}key.

Auto Erase Memory is set.

KSelect [DoD]using the {U} or {T} key, and then press the {qEnter}key.

Auto Erase Memory is set.

Important

❒When Auto Erase Memory is set to [On], temporary data that remained on the

hard disk when Auto Erase Memory was [Off]might not be overwritten.

Note

❒Should the main power switch of the printer be turned off before overwriting

is completed, the temporary data will remain on the hard disk until the main

power switch is next turned on and overwriting is resumed.

❒If the overwriting method is changed while overwriting is in progress, the re-

mainder of the temporary data will be overwritten using the method set orig-

inally.

Canceling Auto Erase Memory

For 4 line display model:

AFollow steps Ato Cin “Auto Erase Memory Setting”.

BSelect [Off]using the {U} or {T} key, and then press the {OK}key.

Auto Erase Memory is disabled.

For 2 line display model:

AFollow steps Ato Din “Auto Erase Memory Setting”.

BSelect [Off]using the {U} or {T} key, and then press the {qEnter}key.

Auto Erase Memory is disabled.

Note

❒To set Auto Erase Memory to [On]again, repeat the procedure in “Auto Erase

Memory Setting”.

Types of Data that Can or Cannot Be Overwritten

The following table shows the types of data that can or cannot be overwritten by

Auto Erase Memory.

*1 A Sample Print, Locked Print, or Hold Print job can only be overwritten after it has

been executed. Stored print jobs can be overwritten by Auto Erase Memory only if

they have been deleted in advance.

*2 Image overlay data can be overwritten by Auto Erase Memory only if it is deleted in

advance.

Data overwritten by Auto

Erase Memory

Printer • Print Jobs

• Sample Print/Locked

Print/Hold Print/Stored

Print Jobs *1

• Spool Printing jobs

• PDF Direct Print data

Data not overwritten by Auto

Erase Memory

Counters stored under each user code

Image overlay data *2

Erase All Memory

This can be specified by the machine administrator.

You can erase all the data on the hard disk by writing over it. This is useful if you

relocate or dispose of your printer.

Important

❒If you select Erase All Memory, the following are also deleted: user codes,

counters under each user code, user stamps, printer fonts downloaded by us-

ers, applications using Embedded Software Architecture, SSL server certifi-

cates, and the printer’s network settings.

❒Should the power switch of the printer be turned off before Erase All Memory

is completed, overwriting is canceled.

❒Make sure the power switch is not turned off during overwriting.

For 4 line display model:

ADisconnect communication cables connected to the printer.

BPress the {Menu}key.

CSelect [Security Options]using the {U} or {T} key, and then press the {OK}key.

DSelect [Erase All Memory]using the {U} or {T} key, and then press the {OK}key.

ESelect the method of erasing the data.

Select the method of erasing the data from [NSA], [DoD], or [Random Numbers].

If you select [Random Numbers], proceed to step F.

If you select [NSA]proceed to step H.

If you select [DoD], proceed to step I.

FSelect [Random Numbers]using the {U} or {T} key, and then press the {OK}key.

GEnter the number of times that you want to overwrite using the {U} or {T}

key, and then press the {OK}key.

HSelect [NSA]using the {U} or {T} key, and then press the {OK}key.

ISelect [DoD]using the {U} or {T} key, and then press the {OK}key.

JWhen overwriting is completed, press [Exit], and then turn off the power.

For 2 line display model:

ADisconnect communication cables connected to the printer.

BPress the {Menu}key.

Select

[

Maintenance

]

using the

{U}

{T}

key, and then press the

{

Enter

}

key.

Select

[

Erase All Mem.

]

using the

{U}

{T}

key, and then press the

{

Enter

}

key.

Select

[

Erase Method

]

using the

{U}

{T}

key, and then press the

{

Enter

}

key.

FSelect the method of erasing the data.

Select the method of erasing the data from [NSA], [DoD], or [Random].

If you select [Random], proceed to step G.

If you select [NSA]proceed to step I.

If you select [DoD], proceed to step J.

GSelect [Random]using the {U} or {T} key, and then press the {qEnter}key.

HEnter the number of times that you want to overwrite using the {U} or {T}

key, and then press the {qEnter}key.

After the settings are made, about two seconds later, the screen return to the

Erase All Memory setup menu.

ISelect [NSA]using the {U} or {T} key, and then press the{qEnter}key.

After the settings are made, about two seconds later, the screen return to the

Erase All Memory setup menu.

JSelect [DoD]using the {U} or {T} key, and then press the {qEnter}key.

After the settings are made, about two seconds later, the screen return to the

Erase All Memory setup menu.

KStart overwriting all memory. Select [Start Erase]using the {U} or {T} key,

and then press the {qEnter}key.

LWhen overwriting is completed, press the {qEnter}key, and then turn off

the power.

Note

❒Before erasing the hard disk, you can back up user codes, and counters for

each user code data using SmartDeviceMonitor for Admin. For details, see

SmartDeviceMonitor for Admin Help.

❒If the power is turned off when Erase All Memory is in progress, overwriting

will start again when you next turn on the power.

❒If an error occurs before overwriting is completed, turn off the main power.

Turn it on again, and then repeat from the start of the procedure.

Reference

For details about logging on and logging off with administrator authentica-

tion, see Security Guide or Note to Administrator.

Andere Handbücher für P7675

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Gestetner Software Handbücher

Gestetner

Gestetner P7145 Bedienungsanleitung

Gestetner

Gestetner 27AO Bedienungsanleitung

Gestetner

Gestetner DSm651 Betriebsanleitung

Gestetner

Gestetner DSm755 Betriebsanleitung

Gestetner

Gestetner P7032 Bedienungsanleitung

Gestetner

Gestetner DSm725e Betriebsanleitung

Gestetner

Gestetner P7126 Bedienungsanleitung

Beliebte Software Handbücher anderer Marken

COMPRO

COMPRO COMPROFM Bedienungsanleitung

Muratec

Muratec OFFICEBRIDGE ONLINE Bedienungsanleitung

Oracle

Oracle Contact Center Anywhere 8.1 Bedienungsanleitung

Adobe

Adobe 65007312 - Photoshop Lightroom Handbuch

Avaya

Avaya NULL One-X for RIM Blackberry Bedienungsanleitung

HP ProLiant BL420c Bedienungsanleitung

PS Audio

PS Audio PowerPlay Betriebsanleitung

Brady

Brady LOCKOUT PRO 3.0 Service-Handbuch

Avaya

Avaya Interaction Center Bedienungsanleitung

Texas Instruments

Texas Instruments TI-83 Plus Silver Edition Handbuch

Novell

Novell GROUPWISE 8 - INTERNET AGENT Bedienungsanleitung

Oracle

Oracle Application 9i Bedienungsanleitung

Acer

Acer RDM Bedienungsanleitung

Canon

Canon Vixia HF21 Bedienungsanleitung

Canon

Canon ZR950 Bedienungsanleitung

Samsung

Samsung Auto Backup Bedienungsanleitung

Polycom

Polycom Vortex EF2201 Montage- und Bedienungsanleitung

Brocade Communications Systems

Brocade Communications Systems Brocade 8/12c Bedienungsanleitung