G-Case/JBX Junction Box Quick Start Guide
This Quick Installation Guide describes how to install the Outdoor Bracket Wall Mounts of G-Cam/E3 series with G-Case/JBX.
Package contents
Please check the contents of the packaging for completeness. It contains:
1x nickel-plated fitting 1x plastic conduct 2x sealing insert 1 x 6 mm 2x sealing insert 2 x 6 mm
4x M8 x 25 hexagon
socket head screw
4x M8 hexagon nut 4x spring washer, 8x seal ring 8x M8 flat washer
Bracket Wall Mount G-Cam/EBWM-003 (Screw connection) and G-Cam/BWM-001 (L-Mount version):
In combination with the appropriate mounting adapters G-Cam/EBDA-00x the following cameras can be installed:
- G-Cam/EBWM-003 + /EBDA-002: G-Cam/EHC-3285 /-3261 and EFD-3266
- G-Cam/EBWM-003 + /EBDA-001: G-Cam/EFD-3245 /-3255 and EHC-3180
- G-Cam/BWM-001 + /EBDA-003: G-Cam/EFD-3247/-3257/-3410 and EFD-3430
G-Cam/EBWM-003 G-Cam/BWM-001 G-Cam/EBDA-001 G-Cam/EBDA-002 G-Cam/EBDA-003
NOTE! This explicit procedure for installing the wall mounts on the box cover has to be done before cabling in the box!
If only PoE is used, the sealing insert with one 6 mm hole is adequate.
Bracket Wall Mount G-Cam/EBWM-003 (Screw connection))
Step 1: Prepare the wall mount like shown. The rubber surround (G-Cam/EBDA accessory)
must be plugged over the wall mount outlet.
Step 2: First pull the network cable through the nickel-plated conduct
of the G-Case/JBX. Now the cable must be lead (see picture) through
the plastic conduct, the slot of the sealing insert into its center and the
nickel-plated fitting. Than push the network cable through the wall
mount and the G-Cam/EBDA-00x (see picture).
Step 3: The connection to the camera has to be done in the G-Cam/EBDA, if the camera owns fixed cable whips.
Or in the camera, if the camera is cable less.
Fix the respective camera with the matching screws (G-Cam/EBDA accessory pack) onto the adapter.
Step 4: Screw this combination into the wall mount and press the
rubber surround close to the adapter, like shown in the picture
right hand.
The example at right hand (G-Cam/EFD-3266) shows the combi-
nation after completion. To mount the G-Cam/EBDA-001 please
follow these steps, too.
Bracket wall mount G-Cam/BWM-001 (L-mount connection)
The four fixdomes EFD-3247/3257/3410 and 3430 do NOT own cable whips.
Follow the steps 1 and 2 as described for G-Cam/EBWM-003. Note that a rubber surround is not needed here.
G-Cam/BWM-001 G-Cam/EBDA-003 Cable routing EBDA-003
Step 3: Pull the network cable through the cable gland as shown here. Close
the side opening of the camera with the screw cap. The lateral view should be
now as shown in the picture right hand.
Pic. left: Cable gland (order of rubber seals for side opening only)
Pic. right: Bottom opening (take care for correct order of the rubber seals!)
Step 4: Stick the network cable into the RJ-45 plug inside the camera and carefully pull it back through the cable gland. Also
do this (like it is described in step 2) into the G-Case/JBX.
Step 5: Place the open camera housing inside the G-Cam/EBDA and fit it with the 2 M4 screws from the adapter’s acces-
sory kit.
Step 6: Place the camera cover onto the camera socket (note the blue arrows) and close it with the 2 security torx screws.
Step 7: Stick the EBDA into the wall mount and turn it counterclockwise until you can
see the thread in the wall mount´s drilling hole. Fit the adapter with the screw set from
G-Cam/EBDA accessory kit. Take care of the correct order (see pic.).
From left to the right: Screw, spring washer, washer (deepening to the right), rubber ring
The combination camera + wall mount should look as shown here:
Note! None of speed domes (like G-Cam/ESD or /GNSD) may be mounted!
Step 8: Stick the sealing insert (Step 1) into the plastic conduct.
The sealing audibly snaps in when it reaches its correct place. Push
the plastic conduct into the nickel-plated conduct of the G-Case/JBX
(you find the only correct position by turning the plastic conduct). Fix
the nickel-plated fitting slightly. Carefully pull the network cable
through the box cover, until the wall mount stops few centimeters over
the fitting.
Finally fix the fitting.
Step 9: Place the wall mount on the box cover like shown here.
Step 10: Using the accessories of the G-Case/JBX.
In each case take a screw with a flat washer and stick it through the
four holes in the wall mount and the G-Case/JBX cover.
Inside the box place 2 seal rings each over every screw, then a flat
washer, one spring washer and one hexagon nut.
83 mm
167 mm
