Instructions for Use G-STPerimeter+ G3
Front View (Without Cover)
No. Element
1 Operation indicator LED Power (white).
2
Error: No function
3 Recording LED Record HDD (white).
4 USB ports.
5 Trigger key Action (can be operated with a finger).
6 Alarm Reset key (can be operated with 2 mm stylus).
7 Reset key (can be operated with 2 mm stylus).
8 Power key PWR (can be operated with 2 mm stylus).
Rear View
General Safety Instructions
Commissioning
The device may only be commissioned by qualified
personnel who are familiar with the device and the
technology.
Make sure that all applicable safety requirements are
fulfilled.
WARNING
Electrical voltages!
Personal and property damage
►
All connection work should only be performed
on the device when it is switched off.
►
Do not remove the housing cover.
WARNING
Electrical voltages!
Personal and property damage
►
Do not use the device if it is damaged.
►
Disconnect the device from the power supply.
Do not use the supply cable for purposes for which it is
not intended. Protect the cable from heat, oil, and sharp
edges.
In dangerous situations or in case of malfunctions,
disconnect the device from the power supply immediately.
Repair and Maintenance
Ensure that the device is repaired professionally. Mark
the defect clearly and disconnect the power plug so that
no accidents or damage can occur due to a defective
device or be caused by it until the device is repaired.
Do not remove the housing cover! There are only
maintenance-free components inside the device.
WARNING
Electrical voltages!
Personal and property damage
►
Disconnect the device from the power supply
during all repair and maintenance work.
►
Work on the electrical equipment may only be
performed by a qualified electrician.
CAUTION
Danger due to the use of non-original parts!
Personal and property damage
►
Only use original spare parts.
WARNING
Explosion hazard!
If the mainboard battery is replaced by an unsuitable
battery type, explosions may occur.
►
Make sure that a suitable battery type is used.
►
Dispose the battery according to the valid legal
requirements and local regulations.
For the connection of control lines, please refer to the
instructions in the user manual.
Use a socket with a protective contact to connect the
power-supply unit.
Ensure a power supply of 110 VAC to 230 VAC. When
connecting external contacts, do not apply voltages above
3.3 V, this may cause damage.
The operating system is precisely preconfigured for your
device.
Important Notice for Product Usage:
Please be aware that the device name must not be altered,
as system licensing is directly tied to the device name.
Post-licensing is no longer possible if the device name is
changed, and the proper operation of the system cannot be
guaranteed.
However, if you still need to change the device name, we
strongly recommend that you make a note of the original
device name and keep it in a well-known and secure
location. This ensures that you can access the original
license information if needed.
Operation
When operating the device, the local applicable laws, other
regulations, standards, and rules of technology must be
observed. In the interest of a safe work process, operating
company and supervisors are responsible for their
compliance. During all work, check the device for any
damage. All parts must be correctly mounted and fulfill all
conditions to ensure proper operation.
Password disclosure:
,QWKH:LQGRZV/RJLQ dialog box, enter the following:
Then assign your own new password and write it down!
The password must be at least six characters long.
The password must contain characters from three of the
following categories:
Upper case letters (A to Z)
Lowercase letters (a through z)
Numbers in base 10 (0 to 9)
Non-alphabetic characters (for example !, $, #, %)
Please note that this is the Windows system
password, it is not possible to recover the password if
it is lost! The user profile Administrator allows full
access to your G-ST.
Confirm with the "ENTER" key.
Administrator
User name:
Pass
word: Pa$$w0rd
No.
Element
1
Connection for power supply
2
Display port (4x) for connecting a PC monitor
3
2x Ethernet ports 10/100/1000 MBit/s base-TX iAMT interface and 10/100/1000/2500 MBit/s
base-TX interface
4 4x USB 3.2 (Gen1), 2x USB 3.2 (Gen2)
5
Serial RS-232 interface COM1 (9-pin Sub-D connector)
6
USB-C 3.2 (Gen2)
7Audio connections
4 mini display port outputs for connecting a PC monitor8
