Gibson GES831CS0 Bedienungsanleitung

P/N 131593000A (0403)

Printed in U.S.A.

For your safety, the information in this manual must be followed to minimize the risk of fire

or explosion or to prevent property damage, personal injury or loss of life.

-Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other

appliance.

- WHAT TO DO IF YOU SMELL GAS:

•Do not try to light any appliance.

•Do not touch any electrical switch; do not use any phone in your building.

•Clear the room, building or area of all occupants.

•Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's instructions.

•If you cannot reach your gas supplier, call the fire department.

Installation and service must be performed by a qualified installer, service agency or the gas supplier.

Important Safety Instructions

Read all instructions before using this laundry center.

To reduce the risk of fire, electrical shock, or injury to persons when

using this laundry center, comply with the basic warnings listed below.

Failure to comply with these warnings could result in serious personal injuries.

Prevent Fire

Do not wash or dry items that have been previously cleaned in,

soaked in, or spotted with gasoline, cleaning solvents, kerosene, waxes, etc. Do not

store these items on or near the dryer. These substances give off vapors that could

ignite or explode.

Do not place items exposed to cooking oils in your dryer. Items

contaminated with cooking oils may contribute to a chemical reaction that could

cause a load to catch fire.

Do not put oily or greasy rags or clothing on top of the laundry center.

These substances give off vapors that could ignite the materials.

Do not add gasoline, cleaning solvents, or other flammable or

explosive substances to the wash water. These substances give off vapors that could

ignite or explode.

Under certain conditions, hydrogen gas may be produced in a hot

water system that has not been used for 2 weeks or more. HYDROGEN GAS IS

EXPLOSIVE. If the hot water system has not been used for such a period, before

using the washer, turn on all hot water faucets and let the water flow from each for

several minutes. This will release any accumulated hydrogen gas. Hydrogen gas

is flammable; do not smoke or use an open flame during this time.

To prevent fire, do not use heat to dry items containing plastic, foam

rubber or similarly textured rubber-like materials, or items containing feathers or

down. Use Air Fluff (No Heat) only.

Product Registration

Thank you for choosing this laundry

center. This owner's guide will explain

proper operation and care.

Record Your Model and Serial

Numbers

Record below the model and serial

numbers found on the laundry center

serial plate located on the inside of the

dryer door. Keep these numbers for

future reference.

Model Number __________________

Serial Number ___________________

Date of Purchase ________________

The self-addressed PRODUCT

REGISTRATION CARD should be filled in

completely, signed and returned.

Versión en español

Si desea obtener una copia en español

de este Manual del Usuario, sírvase

escribir a la dirección que se incluye a

continuación. Solicite la P/N 131547000.

Spanish Owner's Guides

Frigidaire Company

P. O. Box 9061

Dublin, Ohio 43017-0961

Contents

Versión en español ..................... 2

Product Registration ........................ 2

Important Safety Instructions ........ 2-3

Washing Procedures ..................... 5-7

Stain Removal ............................. 7-8

Common Washing Problems ........... 9

Drying Procedures ......................... 10

Features........................................ 11

Common Drying Problems ............ 11

Care and Cleaning .................. 12-13

Avoid Service Checklist ............ 13-15

Warranty and Service .................... 16

Clean the dryer lint screen before or after each load. The interior of

the dryer, lint screen housing and exhaust duct should be cleaned approximately

every 18 months by qualified service personnel. An excessive amount of lint build-up

in these areas could result in inefficient drying and possible fire. See Care and

Cleaning, pages 12-13.

Do not operate the dryer if the lint screen is blocked, damaged or

missing. Fire hazard, overheating and damage to fabrics can occur. If your dryer has

a drying rack, always replace the lint screen when finished using the drying rack.

Keep area around the exhaust opening and surrounding areas free

from the accumulation of lint, dust and dirt.

Do not obstruct the flow of ventilating air. Do not stack or place

laundry or throw rugs against the front or back of the laundry center.

Do not spray any type of aerosol into, on or near laundry center at any

time.

Do not use fabric softeners or products to eliminate static unless

recommended by the manufacturer of the fabric softener or product.

Failure to comply with these warnings could result in fire, explosion, serious bodily

injury and/or damage to the rubber or plastic parts of the laundry center.

Protect Children

Do not allow children to play on or in the laundry center. Close

supervision of children is necessary when the laundry center is used near children. As

children grow, teach them the proper, safe use of all appliances.

Destroy the carton, plastic bag and other packing materials after the

laundry center is unpacked. Children might use them for play. Cartons covered with

rugs, bedspreads or plastic sheets can become airtight chambers.

Keep laundry products out of children's reach. To prevent personal

injury, observe all warnings on product labels.

Before the laundry center is removed from service or discarded,

remove the washer lid and dryer door to prevent accidental entrapment.

Failure to comply with these warnings could result in serious personal injuries.

This Owner's Guide provides general

operating instructions for your laundry

center. It also contains information

about features for several other

models. Your laundry center may not

have every feature included.

Use the laundry center only as

instructed in this Owner's Guide and

the Operating Instructions cards

included with your laundry center.

Note: The instructions appearing in this

Owner's Guide are not meant to cover

every possible condition and situation

that may occur. Common sense and

caution must be practiced when

installing, operating and maintaining

any appliance.

CORRECTCORRECT

CORRECT

Use this way ONLYUse this way ONLY

Use this way ONLY

Grounding type

all receptacle

Power supply

cord with 3-prong

grounding plug

Do not under

any circumstances

cut, remove,

or bypass

the grounding prong

from this plug.

Avoid fire hazard or

electrical shock. Do not use an adaptor

plug or extension cord or remove

grounding prong from electrical power

cord. Failure to follow this warning can

cause serious injury, fire or death.

Prevent Injury

To prevent shock hazard and assure stability during operation, the

laundry center must be installed and electrically grounded by a qualified service

person in accordance with local codes. Installation instructions are packed in the

laundry center for the installer's reference. Refer to INSTALLATION INSTRUCTIONS

for detailed grounding procedures. If the laundry center is moved to a new location,

have it checked and reinstalled by a qualified service person.

To prevent personal injury or damage to the laundry center, the

electrical power cord must be plugged into a properly grounded and polarized 3-

prong outlet. The third grounding prong must never be removed. Never

ground the laundry center to a gas pipe. Do not use an extension cord or an

adaptor plug.

Follow package directions when using laundry products. Incorrect

usage can produce poisonous gas--resulting in serious injury or death.

• Do not combine laundry products for use in 1 load unless specified on the label.

• Do not mix chlorine bleach with ammonia or acids such as vinegar.

To prevent serious personal injury and damage to the laundry center:

• All repairs and servicing must be performed by an authorized servicer

unless specifically recommended in this Owner's Guide. Use only authorized

factory parts.

• Do not tamper with controls.

• Do not install or store the laundry center where it will be exposed to the

weather.

ALWAYS disconnect the laundry center from the electrical supply

before attempting any service or cleaning. Failure to do so can result in electrical

shock or injury.

Do not use any type spray cleanser when cleaning dryer interior.

Hazardous fumes or electrical shock could occur.

To prevent injury, do not reach into the washer while parts are

moving. Before loading, unloading or adding items, push in the cycle selector knob

and allow the tub to coast to a complete stop before reaching inside.

To prevent injury, do not reach into the dryer if the drum is moving.

Wait until the dryer has stopped completely before reaching into the drum.

A thermal limiter switch automatically turns off the dryer motor in the unlikely

event of an overheated situation (electric dryers only). A service technician must

replace the thermal limiter switch after correcting the fault.

The washer is equipped with an electrical overload protector. The motor will stop

if it becomes overheated. The washer will automatically restart after a cool down

period of up to 30 minutes, if the washer has not been manually turned off during

this time.

Important SafetyImportant Safety

Important Safety

InstructionsInstructions

Instructions (continued)(continued)

(continued)(continued)

(continued)

Do not use or mix

liquid chlorine bleach with other

household chemicals such as toilet

cleaners, rust removers, acid or

productscontaining ammonia.These

mixtures can produce dangerous

fumes which can cause serious injury

or death.

Washing Prashing Pr

ashing Prashing Pr

ashing Procedurocedur

ocedurocedur

ocedureses

eses

es • Follow the guidelines below for preparing the wash load.

• Read the Washer Operating Instructions card for operating your specific

model.

•Always read and follow fabric care and laundry product labels.

To reduce the risk of fire, electrical shock, or injury to persons, read

Important Safety Instructions, pages 2-4, before operating this washer.

1. Sort laundry into loads that can be washed together.

Sort items by recommended water temperatures, wash time, and agitate/spin

speeds.

• Separate white, light, and colorfast items from dark and noncolorfast items.

• Separate items which shed lint from items which attract lint. Permanent

press, synthetic, knit and corduroy items will pick up lint from towels, rugs

and chenille bedspreads.

• Separate heavily soiled items from lightly soiled items.

• Separate lacy, sheer and loosely knit items from sturdy items.

2. Prepare items for washing.

• Empty pockets.

• Brush off lint and dirt. Shake out rugs and beach towels.

• Close zippers, fasten hooks, tie strings and sashes, and remove nonwashable

trims and ornaments.

• Remove pins, decorative buttons, belt buckles, and other objects which

could be damaged. This also helps protect other items in the wash load.

• Mend rips and tears to prevent further damage during washing.

• Place delicate items such as bras, shoulder pads, hosiery, and belts in a mesh

bag to prevent tangling during the wash cycle.

• Turn knit items inside out to prevent pilling.

3. Pretreat stains and heavy soil.

See Stain Removal, pages 7-8, for details.

4. Add a measured amount of detergent to the wash tub

before adding the laundry load.

Follow detergent manufacturer's directions. The amount required depends on

type of detergent, load size and soil level, and water hardness.

5. If desired, add liquid bleach to Bleach Dispenser (some models).

• Before adding the wash load, add liquid bleach to bleach dispenser located

in left front corner under the lid:

• 3/4 cup (180 ml) for small loads

• 1 cup (240 ml) for large loads

• 1-1/4 cups (300 ml) for extra-large loads.

• Then add 1 cup (240 ml) water to flush the dispenser.

• Do not use powdered bleach in the bleach dispenser.

For models without a bleach dispenser, dilute the recommended amount of

liquid chlorine bleach in 1 quart (.95 L) water. Add it to wash water after

a few minutes of agitation. Do not pour bleach directly on wash load.

BleachDispenser(somemodels)

Place delicate items in a mesh bag.

Emptypockets.

Sort laundry into loads that can be

washedtogether.

Washing Prashing Pr

ashing Prashing Pr

ashing Procedurocedur

ocedurocedur

ocedureses

eses

(continued)(continued)

(continued)

6. Add laundry load to washer.

• Dry load level should not be higher than top row of holes in wash tub.

Do not overload washer.

• Do not put items on top of agitator or wrap them around it. Load items

evenly.

• Combine large and small items in a load. Load large items first. Large items

should not be more than half the total wash load.

• When washing a single heavy item, add 1 or 2 towels to balance the load.

7. If desired, add liquid fabric softener to Fabric Softener

Dispenser (some models).

For models with a built-in dispenser (see picture below to the left):

1. Add liquid softener to the dispenser, following fabric softener label directions.

2. Add water to bring liquid level to fill line on dispenser cap.

3. Remove the dispenser from the agitator after each use. Rinse both cap and

cup with warm water. Replace dispenser in the agitator.

IMPORTANT: Do not stop and restart washer during a spin when using the

fabric softener dispenser.

For models with a removable dispenser (see picture below to the left):

1. Attach fabric softener dispenser to top of agitator by pressing down gently.

2. Add softener to the dispenser, following fabric softener label directions.

3. Add water to bring liquid level to top of the peg in the center of the cup.

4. Remove the dispenser from the agitator after each use. Rinse both lid and

bowl thoroughly with warm water. Reassemble and place dispenser on

agitator or store it nearby.

IMPORTANT: Do not stop and restart washer during a spin when using the

fabric softener dispenser.

For models without a fabric softener dispenser, follow fabric softener label

directions. Add diluted fabric softener to the final rinse. Do not pour fabric

softener directly on the wash load.

8. Set cycle selector knob and washer controls according to

type, size, and soil level of each load, and detergent used.

See Washer Operating Instructions card for your specific model controls.

Donot use liquidchlorine bleach with

otherhouseholdchemicals.

RemovableFabricSoftenerDispenser

(somemodels)

Donot load items above

top row of holes in wash tub.

Built-InFabricSoftenerDispenser

(somemodels)

9. Start the washer.

Close the washer lid and pull out the cycle selector knob. Washer will fill and

agitate with the lid open. The tub will not spin unless the lid is closed.

• To stop the washer, push in the cycle selector knob.

• To change a cycle, push in the cycle selector knob. Turn it clockwise to the

desired setting. Pull out the knob to restart the washer.

10.Remove items when the cycle is completed.

For your safety, the lid locks when the tub is spinning. It will remain locked for

about 1 minute after the tub stops spinning.

• To open the lid during a spin, push in the cycle selector knob and wait about

1 minute for the lid lock to release. Do not force open the locked lid.

Place washed items in automatic dryer, line dry, or dry flat as directed by fabric

care label. Excess wrinkling, color transfer or odors may develop in items left in

the washer after the cycle has ended.

Stain RemovalStain Removal

Stain Removal Safe Stain Removal Procedures

To reduce the risk of fire or serious injury to persons or property,

comply with the basic warnings listed below:

• Read and comply with all instructions on stain removal products.

• Keep products in their original labeled containers and out of children's

reach.

• Thoroughly wash any utensil used.

• Do not combine stain removal products, especially ammonia and chlorine

bleach. Dangerous fumes may result.

• Never wash items which have been previously cleaned in, washed in,

soaked in or spotted with gasoline, dry cleaning solvents or other flammable

or explosive substances because they give off vapors that could ignite or

explode.

• Never use highly flammable solvents, such as gasoline, inside the home.

Vapors can explode on contact with flames or sparks.

For successful stain removal:

• Remove stains promptly.

• Determine the kind of stain, then follow recommended treatment in the

stain removal chart on the next page.

• To pretreat stains, use a prewash product, liquid detergent, or a paste made

from granular detergent and water.

• Use cold water on unknown stains because hot water can set stains.

• Check care label instructions for treatments to avoid on specific fabrics.

• Check for colorfastness by testing stain remover on an inside seam.

• Rinse and wash items after stain removal.

Followfabriccarelabelinstructions.

Do not combine stain removal products.

STAINSTAIN

STAIN

Adhesive tape, chewing

gum, rubber cement

Baby formula, dairy

products, egg

Beverages (coffee, tea,

soda,

juice, alcoholic beverages)

Blood

Candle wax, crayon

Chocolate

Collar or cuff soil, cosmetics

Dye transfer on white

fabric

Grass

Grease, oil, tar (butter, fats,

salad dressing, cooking oils,

car grease, motor oils)

Ink

Mildew, scorch

Mud

Mustard, tomato

Nail polish

Paint, varnish

Perspiration

Rust, brown or yellow

discoloration

Shoe polish

Urine, vomit, mucus, feces

Apply ice. Scrape off excess. Place stain face down on paper towels. Saturate with prewash stain remover or

nonflammable dry cleaning fluid.

Use product containing enzymes to pretreat or soak stains. Soak for 30 minutes or more. Wash.

Pretreat stain. Wash using cold water and bleach safe for fabric.

Rinse with cold water. Rub with bar soap. Or, pretreat or soak with product containing enzymes. Wash using

bleach safe for fabric.

Scrape off surface wax. Place stain face down between paper towels. Press with warm iron until wax is

absorbed. Replace paper towels frequently. Treat remaining stain with prewash stain remover or nonflammable

dry cleaning fluid. Hand wash to remove solvent. Wash using bleach safe for fabric.

Pretreat or soak in warm water using product containing enzymes. Wash using bleach safe for fabric.

Pretreat with prewash stain remover or rub with bar soap.

Use packaged color remover. Wash using bleach safe for fabric.

Pretreat or soak in warm water using product containing enzymes. Wash using bleach safe for fabric.

Scrape residue from fabric. Pretreat. Wash using hottest water safe for fabric. For heavy stains and tar, apply

nonflammable dry cleaning fluid to back of stain. Replace towels under stain frequently. Rinse thoroughly. Wash

using hottest water safe for fabric.

Some inks may be impossible to remove. Washing may set some inks. Use prewash stain remover, denatured

alcohol or nonflammable dry cleaning fluid.

Wash with chlorine bleach if safe for fabric. Or, soak in oxygen bleach and hot water before washing. Badly

mildewed fabrics may be permanently damaged.

Brush off dry mud. Pretreat or soak with product containing enzymes.

Pretreat with prewash stain remover. Wash using bleach safe for fabric.

May be impossible to remove. Place stain face down on paper towels. Apply nail polish remover to back of stain.

Repeat, replacing paper towels frequently. Do not use on acetate fabrics.

WATER BASED: Rinse fabric in cool water while stain is wet. Wash. Once paint is dry, it cannot be removed. OIL

BASED AND VARNISH: Use solvent recommended on can label. Rinse thoroughly before washing.

Use prewash stain remover or rub with bar soap. Rinse. Wash using nonchlorine bleach in hottest water safe for

fabric.

For spots, use rust remover safe for fabric. For discoloration of an entire load, use phosphate detergent and

nonchlorine bleach. Do not use chlorine bleach because it may intensify discoloration.

LIQUID: Pretreat with a paste of granular detergent and water. PASTE: Scrape residue from fabric. Pretreat

with prewash stain remover or nonflammable dry cleaning fluid. Rinse. Rub detergent into dampened area.

Wash using bleach safe for fabric.

Pretreat or soak in product containing enzymes. Wash using bleach safe for fabric.

TREATMENTTREATMENT

TREATMENT

Stain RemovalStain Removal

Stain Removal

•Add detergent before wash load. Then

start washer.

•Dilute fabric softener with water.

•Sort items by soil level and color.

•Use correct amount of detergent, hottest

water and bleach safe for fabric.

•Use correct amount of detergent and

hottest water safe for fabric.

•Do not pour liquid fabric softener

directly on fabric. See package directions

or Washing Procedures for proper

diluting.

•Never pour chlorine bleach directly on

fabric.

•Check condition of items before washing.

See Washing Procedures for preparing

and loading the wash load.

•See Washing Procedures for sorting and

preparing the wash load.

•Do not overload washer.

•Use correct amount of detergent, water

temperature and water level.

•Use fabric softener in the washer to

lubricate fibers.

•When ironing, use spray starch or fabric

finish on collars and cuffs.

•Turn items inside out to reduce abrasion.

•Increase water temperature using hottest

water safe for fabric.

•Do not overload washer.

•Use liquid detergent or use

nonprecipitating water conditioner with

nonphosphate granular detergent.

•Do not overload washer.

•Remove items from washer as soon as

cycle is completed.

•Use liquid fabric softener.

•Wash synthetics frequently using water at

least 100°F (37°C ) and correct water level.

•Use nonprecipitating water softener.

•Before washing, run hot water for a few

minutes to clear lines.

•Drain water heater occasionally.

•For an ongoing problem, install an iron

filter in your water supply system.

Common WCommon W

Common Washing Prashing Pr

ashing Prashing Pr

ashing Problemsoblems

oblemsoblems

oblems

SOLUTIONSSOLUTIONS

SOLUTIONS

PROBLEMPROBLEM

PROBLEM PREVENTIVE MEASURESPREVENTIVE MEASURES

PREVENTIVE MEASURESPREVENTIVE MEASURES

PREVENTIVE MEASURES

•If caused by detergent, mix 1 cup (240

ml) white vinegar with 1 quart (.95 L)

water in a plastic container. Soak item 1

hour. Rinse.

•If caused by fabric softener, rub stains

with bar soap. Wash.

•Rewash with correct amount of

detergent and hottest water safe for

fabric. Add bleach safe for fabric.

•Treat with prewash stain remover or

liquid detergent.

•Increase detergent and water

temperature. Rewash.

•Rub fabric softener stains with bar soap.

•May be irreversible if rips, tears and

seams cannot be mended.

•Reduce load size. Rewash using correct

water temperature, water level, and

amount of detergent.

•Add nonprecipitating water conditioner

to wash water.

•Add liquid fabric softener to final rinse.

•Dry load in dryer.

•Remove lint with lint brush or roller.

•Use a lint brush or shaver to remove

pills.

•Reduce load size.

•Add dissolved detergent to tub . Rewash

load.

•Mix 1 cup (240 ml) white vinegar to 1

gallon (3.8 L) warm water in plastic

container. Soak item. Rinse and rewash.

•Reduce load size.

•Rinse in cold water with liquid fabric

softener.

•Soak in detergent booster or product

containing enzymes.

•Wash in hot water (120°F/49°C) using full

permanent press cycle. Increase

detergent.

Add bleach safe for fabric.

•Or, treat with color remover.

•To restore discolored load of whites, use

rust remover safe for fabric.

Do not use chlorine bleach to remove

rust stains. It may intensify

discoloration.

POSSIBLE CAUSESPOSSIBLE CAUSES

POSSIBLE CAUSES

Many washing problems involve poor soil and stain removal, residues of lint and scum, and fabric damage. For satisfactory washing

results, follow these suggestions provided by The Soap and Detergent Association.

•Detergent or liquid fabric softener

did not dissolve or disperse.

•Not enough detergent.

•Wash water temperature too

low.

•Incorrect sorting.

•Not enough detergent.

•Undiluted liquid fabric softener

poured directly on fabric.

•Incorrect use of chlorine bleach.

•Unfastened zippers, hooks,

buckles.

•Rips, tears and broken threads.

•Overloading the washer.

•Degradation of fabric.

•Incorrect sorting.

•Tissues left in pocket.

•Overloading the washer.

•Not enough detergent.

•Undissolved detergent has left

residue.

•Static cling is attracting lint.

•Load washed too long.

•Pilling is normal with synthetic and

permanent press fabrics. This is

due to abrasion from normal

wear.

•Undissolved detergent.

•Some nonphosphate granular

detergents can combine with

hard water minerals to form a

residue.

•Overloading the washer.

•Agitation time too short.

•Wash water temperature too

low.

•Not enough detergent.

•Iron or manganese in water

supply, water pipes, or water

heater.

Blue stains

Discoloration,

graying

Greasy, oily stains

Holes, tears, or

snags

Lint

Pilling

(Fibers break off,

ball up and cling to

fabric)

Residue or powder

on dark items;

Stiff, harsh fabrics.

Wrinkling

Yellow buildup of

body soil on

synthetic fabrics

Yellow or brown

rust stains

•Follow the guidelines below for preparing the load for drying.

•Read the Dryer Operating Instructions card for operating your specific model.

• Always read and follow fabric care labels and laundry product labels.

To reduce the risk of fire, electrical shock, or injury to persons, read

Important Safety Instructions, pages 2-4, before operating this dryer.

1. Prepare items for drying.

•Dry items of similar fabric, weight and construction in the same load.

•Separate dark items from light-colored items. Separate items that shed lint

from those that attract lint. If an item sheds lint, turn it inside out.

•Be sure buckles, buttons and trim are heatproof and won't damage the drum

finish. Close zippers, fasten hooks and Velcro®-like fasteners. Tie strings and

sashes to prevent snagging and tangling.

•If possible, turn pockets inside out for even drying.

•Check for stains which may not have been removed in washing. Dryer heat

may permanently set some stains. Repeat stain removal process before

drying.

•Place small items in a mesh bag to prevent tangling and for easy removal.

2. Check that lint screen is clean and in place.

3. Load the dryer.

• The average load will fill the drum 1/3 to 1/2 full. Items need room to tumble

freely for even drying and less wrinkling. Do not overload dryer.

• When drying large items, dry only 2 or 3 at a time. Fill out the load with small

and medium sized items.

• For delicate or very small loads, add 2 lint-free towels for better drying, less

wrinkling, and to prevent grease stains caused by fabric softener sheets.

• Do not overdry items. Overdrying can cause wrinkling, shrinkage, harshness,

and a build-up of static electricity, which can produce more lint.

• If desired, add a dryer fabric softener sheet.

4. Close the dryer door and set dryer controls (some models).

See Dryer Operating Instructions card for your specific model controls.

5. Turn cycle selector clockwise to the desired setting.

6. Start the dryer.

• Push Start button for 2 seconds.

• To add or remove items when the dryer is running, open the door. The dryer

will always stop when the door is opened. Allow the drum to come to a

complete stop before reaching inside.

• To restart dryer, close the door then push Start button. Hold for 1-2 seconds

and release.

7. When the cycle ends, remove items immediately and hang

or fold. If load is removed before the cycle ends, turn cycle selector to OFF.

DrDr

Drying Prying Pr

ying Prying Pr

ying Procedurocedur

ocedurocedur

ocedureses

eses

Followfabriccarelabelinstructions.

Fill dryer drum 1/3 to 1/2 full.

Place small items in a mesh bag.

Inhaltsverzeichnis

Andere Gibson Waschmaschine Trockner Handbücher

Gibson

Gibson Spacemaster EL27M6-A Bedienungsanleitung

Beliebte Waschmaschine Trockner Handbücher anderer Marken

Whirlpool

Whirlpool WFC8090GX Bedienungsanleitung

Whirlpool

Whirlpool LTE5243DQ6 Bedienungsanleitung

Bosch

Bosch XQG100-WDU285H00W Bedienungsanleitung

Beko

Beko HTE10736XS Bedienungsanleitung

AEG

AEG L76685NWD Bedienungsanleitung

LG FWV1128WTSA Bedienungsanleitung

Electrolux

Electrolux WTSL 6 E201 Bedienungsanleitung

AEG

AEG OKO_LAVAMAT 1260 Bedienungsanleitung

Blomberg

Blomberg LRI285411 Bedienungsanleitung

Franke

Franke FWD 1400-6EI Bedienungsanleitung

Hitachi

Hitachi BD-W3300 Bedienungsanleitung

Whirlpool

Whirlpool FWDG96148SBS GCC Installations- und Betriebshandbuch

Equator

Equator EZ 1720 Bedienungsanleitung

NEFF

NEFF V6540X1EU Technisches Datenblatt

Dawlance

Dawlance Spinner DS 9000 CM Bedienungsanleitung

Hoover

Hoover WDYNS 654D-80 Bedienungsanleitung

Hotpoint

Hotpoint H3D91WBUK Bedienungsanleitung

Dexter Laundry

Dexter Laundry C Series Kurzanleitung