Gigabyte GA-8IEML-T Bedienungsanleitung

When you installing AGP card, please make sure the following

notice is fully understood and practiced. If your AGP card has

"AGP 4X notch"(show below), please make sure your AGP card is

AGP 4X (1.5V).

Do not use AGP 2X card (3.3V) in this motherboard. It will burn

and damage the motherboard due to Intel®845(E/G) / 850(E)

chipset can't support AGP 2X(3.3V).

Example 1: Diamond Vipper V770 golden finger is compatible with 2X/

4X mode AGP slot. It can be switched between AGP 2X(3.3V) or

4X (1.5V) mode by adjusting the jumper. The factory default for this card

is 2X (3.3V). If you install this card in GA-8IEML-T(-C) (or any AGP 4X

only) motherboards without switching the jumper to 4X mode (1.5V), it

will burn the motherboard.

Example 2: Some ATi Rage 128 Pro graphics cards made by “Power

Color”, the graphics card manufacturer & some SiS 305 cards, their

golden finger is compatible with 2X/4X mode AGP slot, but they support

2X(3.3V) only. If you install this card in GA-8IEML-T(-C) (or any AGP 4X

only) motherboards, it will burn the motherboard.

Note : Although Gigabyte's AG32S(G) graphics card is based on ATi Rage

128 Pro chip, the design of AG32S(G) is compliance with AGP 4X (1.5V)

specification. Therefore, AG32S(G) will work fine with Intel®845(E/G)

/ 850(E) based motherboards.

0The author assumes no responsibility for any errors

or omissions that may appear in this document nor

does the author make a commitment to update the

information contained herein.

0Third-party brands and names are the property of

their respective owners.

0Please do not remove any labels on motherboard, this

may void the warranty of this motherboard.

0Due to rapid change in technology, some of the

specifications might be out of date before publication

of this booklet.

FCC Part 15, Subpart B, Section 15.107(a) and Section 15.109(a),

Class B Digital Device

DECLARATION OF CONFORMITY

Per FCC Part 2 Section 2.1077(a)

Responsible Party Name:

Address:

Phone/Fax No:

hereby declares that the product

Product Name:

Conforms to the following specifications:

This device complies with part 15 of the FCC Rules. Operation is

subject to the following two conditions: (1) This device may not

cause harmful and (2) this device must accept any inference received,

including that may cause undesired operation.

Representative Person’s Name:

Signature: Eric Lu

Supplementary Information:

Model Number:

17358 Railroad Street

City of Industry, CA 91748

G.B.T. INC. (U.S.A.)

(818) 854-9338/ (818) 854-9339

Motherboard

GA-8IEML-T

Date:

ERIC LU

May 20,2002

Declaration of Conformity

We, Manufacturer/Importer

(full address)

G.B.T. Technology Träding GMbH

Ausschlager Weg 41, 1F, 20537 Hamburg, Germany

declare that the product

( description of the apparatus, system, installation to which it refers)

Mother Board

GA-8IEML-T

is in conformity with

(reference to the specification under which conformity is declared)

in accordance with 89/336 EEC-EMC Directive



EN 55011 Limits and methods of measurement

of radio disturbance characteristics of

industrial,scientific and medical (ISM

high frequency equipment



EN 61000-3-2*

7EN 60555-2

Disturbances in supply systems cause

by household appliances and similar

electrical equipment “Harmonics”



EN 55013 Limits and methods of measurement

of radio disturbance characteristics of

broadcast receivers and associated

equipment



EN 61000-3-3* Disturbances in supply systems cause

by household appliances and similar

electrical equipment “Voltage fluctuations”



EN 55014 Limits and methods of measurement

of radio disturbance characteristics of

household electrical appliances,

portable tools and similar electrical

apparatus

7EN 50081-1 Generic emission standard Part 1:

Residual commercial and light industry

7EN 50082-1 Generic immunity standard Part 1:

Residual commercial and light industry



EN 55015 Limits and methods of measurement

of radio disturbance characteristics of

fluorescent lamps and luminaries

Generic emission standard Part 2:

Industrial environment



EN 55081-2

Immunity from radio interference of

broadcast receivers and associated

equipment

Generic emission standard Part 2:

Industrial environment



EN 55082-2

7EN 55022 Limits and methods of measurement

of radio disturbance characteristics of

information technology equipment

lmmunity requirements for household

appliances tools and similar apparatus



ENV 55104

Cabled distribution systems; Equipment

for receiving and/or distribution from

sound and television signals

EMC requirements for uninterruptible

power systems (UPS)



EN50091-2



EN 55020



DIN VDE 0855



part 10



part 12

(EC conformity marking)

7CE marking

The manufacturer also declares the conformity of above mentioned product

with the actual required safety standards in accordance with LVD 73/23 EEC

Safety requirements for mains operated

electronic and related apparatus for

household and similar general use



EN 60950



EN 60065

Safety of household and similar

electrical appliances



EN 60335

Manufacturer/Importer

Signature:

Name:

(Stamp) Date : May 20, 2002

7EN 60555-3

Timmy Huang



EN 50091-1

USER’S MANUAL

GA-8IEML-T Series

P4 Titan Motherboard

Pentium®4 Processor Motherboard

Rev. 2011

12ME-8IEMLT-2011

GA-8IEML-T Series Motherboard

Table of Content

Item Checklist ......................................................................................... 4

WARNING! ............................................................................................... 4

Chapter 1Introduction .............................................................................. 5

Features Summary ...................................................................................... 5

GA-8IEML-T Series Motherboard Layout ................................................... 7

Chapter 2 Hardware Installation Process ................................................ 8

Step 1: Install the Central Processing Unit (CPU)....................................... 9

Step 1-1: CPU Installation ................................................................................................. 9

Step 1-2: CPU Heat Sink Installation ............................................................................. 10

Step 2: Install memory modules ................................................................ 11

Step 3: Install expansion cards ................................................................. 12

Step 4: Connect ribbon cables, cabinet wires, and power supply ........... 13

Step 4-1: I/O Back Panel Introduction ............................................................................ 13

Step 4-2: Connectors Introduction .................................................................................. 15

Step 4-3: Jumper Introduction ........................................................................................ 21

Chapter 3 BIOS Setup .......................................................................... 23

The Main Menu (For example: BIOS Ver. : F1) ........................................ 24

Standard CMOS Features......................................................................... 26

Advanced BIOS Features .......................................................................... 29

Integrated Peripherals .............................................................................. 31

Table of Content

Power Management Setup ....................................................................... 36

PnP/PCI Configurations ............................................................................. 39

PC Health Status........................................................................................ 40

Frequency/Voltage Control ........................................................................ 42

Top Performance ...................................................................................... 44

Load Fail-Safe Defaults ............................................................................. 45

Load Optimized Defaults ........................................................................... 46

Set Supervisor/User Password .................................................................. 47

Save & Exit Setup ....................................................................................... 48

Exit Without Saving .................................................................................... 49

Chapter 4 Technical Reference ............................................................ 50

Block Diagram ........................................................................................... 50

Q-Flash Introduction.................................................................................. 51

@ BIOSTM Introduction............................................................................... 53

Easy TuneTM 4 Introduction ....................................................................... 54

Chapter 5 Appendix.............................................................................. 55

GA-8IEML-T Series Motherboard

Computer motherboards and expansion cards contain very delicate Integrated Circuit (IC) chips. To

protect them against damage from static electricity, you should follow some precautions whenever you

work on your computer.

1. Unplug your computer when working on the inside.

2. Use a grounded wrist strap before handling computer components. If you do not have

one, touch both of your hands to a safely grounded object or to a metal object, such as

the power supply case.

3. Hold components by the edges and try not touch the IC chips, leads or connectors, or

othercomponents.

4. Place components on a grounded antistatic pad or on the bag that came with the

components whenever the components are separated from the system.

5. Ensure that the ATX power supply is switched off before you plug in or remove the ATX

power connector on the motherboard.

If the motherboard has mounting holes, but they don’t line up with the holes on the base and there are

no slots to attach the spacers, do not become alarmed you can still attach the spacers to the mounting

holes. Just cut the bottom portion of the spacers (the spacer may be a little hard to cut off, so be careful

of your hands). In this way you can still attach the motherboard to the base without worrying about short

circuits. Sometimes you may need to use the plastic springs to isolate the screw from the motherboard

PCB surface, because the circuit wire may be near by the hole. Be careful, don’t let the screw contact

any printed circuit write or parts on the PCB that are near the fixing hole, otherwise it may damage the

board or cause board malfunctioning.

Installing the motherboard to the chassis…

WARNING!

The GA-8IEML-T or GA-8IEML-T-C motherboard

IDE cable x 1 / Floppy cable x 1

CD for motherboard driver & utility (IUCD)

GA-8IEML-T Series user’s manual

I/O Shield

Item Checklist

Introduction

Form Factor y24.4cm x 21cm Micro ATX size form factor, 4 layers PCB.

Motherboard yGA-8IEML-T Series Motherboard:

GA-8IEML-T and GA-8IEML-T-C

CPU ySocket 478 for Intel®Micro FC-PGA2 Pentium®4 processor

y Support Intel®Pentium®4 (Northwood, 0.13 m) processor

yIntel Pentium®4 400/533MHz FSB

y2nd cache depend on CPU

Chipset yChipset 82845E HOST/AGP/Controller

yIntel ICH4 I/O Controller Hub

Memory y2 184-pin DDR DIMM sockets

ySupports DDR266/200 SDRAM

ySupports up to 2GB DRAM (Max)

ySupports only 2.5V DDR DIMM

ySupports 64bit ECC type DRAM integrity mode

I/O Control yWinbond W83627HF

Slots y1 AGP support 4X(1.5V) device

y3 PCI slot supports 33MHz & PCI 2.2 compliant

On-Board IDE y2 IDE bus master (DMA33/ATA66/ATA100) IDE ports for up to 4

ATAPI devices

ySupports PIO mode3,4 (UDMA 33/ATA66/ATA100) IDE & ATAPI

CD-ROM

On-Board Peripherals y1 Floppy port supports 2 FDD with 360K, 720K,1.2M, 1.44M

and 2.88M bytes.

y1 Parallel port supports Normal/EPP/ECP mode

y2 Serial ports (COMA&COMB)

y6 x USB 2.0/1.1 (2 x Rear,4 xFront by cable )

y1 IrDA connector for IR

Hardware Monitor yCPU/System Fan Revolution detect

yCPU/System Temperature detect

ySystem Voltage Detect

Features Summary

Chapter 1 Introduction

to be continued......

GA-8IEML-T Series Motherboard

On-Board Sound yRealtek ALC650 CODEC

yLine Out / 2 front speaker

yLine In / 2 rear speaker(by s/w switch)

yMic In / center& woofer(by s/w switch)

ySPDIF out : by s/w switch

yCD_In / AUX_In / Game port

PS/2 Connector yPS/2 Keyboard interface and PS/2 Mouse interface

BIOS yLicensed AWARD BIOS, 2M bit FWH

On-Board LAN* yBuild in RTL8100(B)L Chipset

AdditionalFeatures yPS/2 Keyboard power on by password

yPS/2 Mouse power on

ySTR(Suspend-To-RAM)

yAC Recovery

yUSB KB/Mouse wake up from S3

ySupports @BIOS

ySupports EasyTune 4

Please set the CPU host frequency in accordance with your processor’s specifications.

We don’t recommend you to set the system bus frequency over the CPU’s specification

because these specific bus frequencies are not the standard specifications for CPU,

chipset and most of the peripherals. Whether your system can run under these specific

bus frequencies properly will depend on your hardware configurations, including CPU,

Chipsets,DDR, SDRAM,Cards….etc.

"*" For GA-8IEML-T only .

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Gigabyte Hauptplatine Handbücher

Gigabyte

Gigabyte GA-8ST800 Bedienungsanleitung

Gigabyte

Gigabyte GA-M720-ES3 Bedienungsanleitung

Gigabyte

Gigabyte GA-MA770-DS3P Bedienungsanleitung

Gigabyte

Gigabyte GA-5DXSL-RH Bedienungsanleitung

Gigabyte

Gigabyte MZ31-AR0 Bedienungsanleitung

Gigabyte

Gigabyte GA-8I955X Royal Bedienungsanleitung

Gigabyte

Gigabyte GA-8ILMT4 Bedienungsanleitung

Gigabyte

Gigabyte GA-B75M-D3V Bedienungsanleitung

Gigabyte

Gigabyte GA-Z87M-HD3 Bedienungsanleitung

Gigabyte

Gigabyte Xeon Processor Motherboard GA-5YXS-RH Bedienungsanleitung

Gigabyte

Gigabyte P4 Titan Series GA-8S655FXUltra Bedienungsanleitung

Gigabyte

Gigabyte GA-6PXSV4 Bedienungsanleitung

Gigabyte

Gigabyte MNIC8CI Bedienungsanleitung

Gigabyte

Gigabyte Z690 AORUS ELITE AX Bedienungsanleitung

Gigabyte

Gigabyte GA-H61TN Bedienungsanleitung

Gigabyte

Gigabyte GA-78LMT-USB3 Bedienungsanleitung

Gigabyte

Gigabyte MU92-TU0 Bedienungsanleitung

Gigabyte

Gigabyte GA-MA770-DS3 Bedienungsanleitung

Gigabyte

Gigabyte GA-B75-DS3V Bedienungsanleitung

Gigabyte

Gigabyte GA-MA790GPT-UD3H Bedienungsanleitung

Gigabyte

Gigabyte GS-R12P4G Bedienungsanleitung

Gigabyte

Gigabyte GA-AB350-Gaming 3 Bedienungsanleitung

Gigabyte

Gigabyte MZ72-HB0 Bedienungsanleitung

Gigabyte

Gigabyte GA-HA65M-D2H-B3 Bedienungsanleitung

Beliebte Hauptplatine Handbücher anderer Marken

DFI

DFI SD170 Bedienungsanleitung

ASROCK

ASROCK ROMED8-2T Bedienungsanleitung

Asus

Asus P2L97A Bedienungsanleitung

Winmate

Winmate IC70 Bedienungsanleitung

Asus

Asus MES-B Bedienungsanleitung

Grantech

Grantech SYS8F377VGGA-3OMN Bedienungsanleitung

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Bedienungsanleitung

Texas Instruments

Texas Instruments ADS8372EVM Bedienungsanleitung

Commell

Commell MS-C73 Bedienungsanleitung

IBT Technologies

IBT Technologies MB860 Bedienungsanleitung

Nvidia

Nvidia TEGRA DG-04927-001_V01 Bedienungsanleitung

Biostar

Biostar M7VIT Bravo Bedienungs- und Montageanleitung

Intel

Intel D33217CK Bedienungsanleitung

Asus

Asus F1A55-M LX PLUS R2.0 Bedienungsanleitung

EPC

EPC EPC9147C Bedienungsanleitung

Asus

Asus EX-B760M-V5 D4 Bedienungsanleitung

EPOX

EPOX MU-8KHA0010 Bedienungsanleitung

Ski-Doo

Ski-Doo Bombardier MPEM 219 700 090 Bedienungsanleitung