Gimenez Ganga Saxun P-190 Bedienungsanleitung

saxun.com

Assembly instructions

Duplex Bioclimatic Pergola P-190

2 columns

Table of Contents

We do not provide the screws for ﬁxing-anchoring to the wall and/or foundations. The ﬁtter must choose the adequate rod/screw/plug/

nut/washer system for ﬁxing and ﬂushing to the foundations and/or wall based on the nature of these surfaces.

In any case, the screws must be in stainless steel.

1. Installation ..................................................................................................................................................................... 4

1.1 Installing the ﬁxation for the column base................................................................................................................................4

1.2 Joining the surface manifolds ....................................................................................................................................................... 7

1.3 Fixing closing beams.........................................................................................................................................................................8

1.4 Assembling the sides .......................................................................................................................................................................9

1.5 Electric pre-installation...................................................................................................................................................................10

1.6 Side joints with closing beam ...................................................................................................................................................... 11

1.7 Joining with opening beam .......................................................................................................................................................... 12

1.8 Joining with central beam ............................................................................................................................................................ 13

1.9 Installing the slats ............................................................................................................................................................................ 15

1.10 Installing the transmission plate ...............................................................................................................................................17

1.11 Installing the “U” proﬁle ................................................................................................................................................................. 18

1.12 Drainage channel closed column ........................................................................................................................................... 20

1.13 Motor installation ............................................................................................................................................................................. 21

2. Electrical connections ...........................................................................................................................................22

The connection of the electrical installation must be done adhering to the current regulations for low voltage (REBT).

2.1 Teleco documentation.................................................................................................................................................................... 22

2.2 Somfy documentation................................................................................................................................................................... 22

2.3 Installation of automatic devices on beams........................................................................................................................ 22

2.4 Perimeter LED installation........................................................................................................................................................... 23

3. Installing column cup .............................................................................................................................................24

4. Maintenance...............................................................................................................................................................25

Before assembling, please read the maximum tightening torque for each type of screw, as indicated in this section.

Annex I Disassembly and disposal of packaging and product components at the end of the product’s service life ..26

Annex II Warranty certiﬁcate .......................................................................................................................................... 30

Bioclimatic Pergola installation check sheet...............................................................................................................32

Check the slope of the ﬂoor and

verify the total height of your

pergola 3D scale plan in order to

place the column bases and the

wall beam.

Position the column bases ac-

cording to the measurements

on the plan and the foundation

slope, considering that the col-

umns must form a 90º angle

with the wall where the pergola

is going to be installed.

123

A A

B B

C C

D D

A A

D D

90º 90º

Total height on the wall

Side view

WALL

TOP VIEW

Length

Width

2 column pergola

TITLE

SIZE DWG NO REV

SCALE

DRAWN

paco

CHECKED

MFG

APPROVED

28/07/2014

SHEET 1OF 1

C LEVEL OFF

2 column pergola

TITLE

SIZE DWG NO REV

SCALE

DRAWN

paco

CHECKED

MFG

APPROVED

28/07/2014

SHEET 1OF 1

C POSITION COLUMN BASES

Height - slope = Total height on the wall

ATTENTION: Leave a clearance

of 100 mm above the beam for the

slats to turn.

1. Installation

1.1 Installing the ﬁxation for the column base

DUPLEX BIOCLIMATIC PERGOLA P-190 2 COLUMNSASSEMBLY INSTRUCTIONS

To obtain the 90º angle with the wall, follow the steps indicated

below:

1 Mark the total width of the pergola on the wall where it will

be installed.

2 At each end of the pergola width mark a point parallel to the

wall at a distance of 2000 mm from it.

3 Make another two marks perpendicular to the ends of the

pergola length at a distance of 2000 mm.

4 The exact measurement of the diagonal lines between the

points marked to obtain the 90º angle must be 2828,4 mm (as

shown in the drawing).

After measuring the 90º angle, install the base ﬁxings using M12

screws (not included), with a quality of at least AISI 304 (stainless

steel).

- Recommended installation is against a wall with reinforced con-

crete ﬂoor of at least 150 mm thickness (or surface of equivalent

strength) by means of 12 mm stainless steel ﬁttings (not included).

250

144

250

Ø14

2.000

2.828,40

2.000 2.000

2.000

212

TOTAL WIDTH OF THE PERGOLA

Top view Closing beam

Left beam Right beam

Column D

Opening beam

Column C

Central beam

DUPLEX BIOCLIMATIC PERGOLA P-190 2 COLUMNSASSEMBLY INSTRUCTIONS

1.2 Joining the surface manifolds

Apply the provided sealant between the contact sides of the

opening and closing beams and their corresponding surface

manifolds.

The opening and closing surface manifolds will be joined, screw-

ing them to the beams.

282,5

250

130

Sellador

Do not bypass this step, it is very important to seal

the mainfold join properly (sealant provided)..

Create a groove at the ends of the opening mani-

fold, before proceeding with the installation, (use a

hammer and a ﬂat screwdriver).

Important

1.3 Fixing closing beams

Drill through holes along the beam at a maximum distance of 500

mm, to insert the screws. The holes must have a diameter large

enough to insert the tools on the side that is not in contact with

the wall.

After verifying the height, ﬁx the beam against the wall, screwing

it through the holes.

The beam will be installed using the adequate screws for the type

of wall and they will always be in stainless steel.

90º

Screws and wall anchors, not provided.

Important

DUPLEX BIOCLIMATIC PERGOLA P-190 2 COLUMNSASSEMBLY INSTRUCTIONS

1.4 Assembling the sides

Join the left beam to column C.

Join the right beam to column D.

Position the duplex bracket on the inside of the column according to the bolt carriers of the beams. Then place two USL (ISO 7380) A2

M6x16 mm screws at the top of the beam, connecting the beam with the ﬂanges of the bracket. Finally, connect the beam to the column

using DIN 933 A2 M8x40 screws.mediante los tornillos DIN 933 A2 M8x40.

1.5 Electric pre-installation

Check the position of the slats incorporating LEDs and the wiring protruding from the beam.

Connector

LED slat

Interior

cabling

At this point in the assembly, all the wiring must be routed to the pergola’s closing beam, where it will be housed together with the

automatic devices, as indicated in point 2.3 Installation of automatic devices on the beam.

Important

Inhaltsverzeichnis

Andere Gimenez Ganga Gartenmöbel Handbücher

Gimenez Ganga

Gimenez Ganga saxun P-190 CR Bedienungsanleitung

Beliebte Gartenmöbel Handbücher anderer Marken

Belleze

Belleze 014-HG-20074 Bedienungsanleitung

Hatteras Hammocks

Hatteras Hammocks DCA1-K-HH Bedienungsanleitung

Kozyard

Kozyard Morgan Aluminum Pergola Bedienungsanleitung

Lemeks

Lemeks Palmako PA120-5959 Installationshandbuch

OLT

OLT 24 Bedienungsanleitung

forest-style

forest-style HACIENDA 2354 Bedienungsanleitung

Courtyard Creations

Courtyard Creations RUS0188-WM Bedienungsanleitung

RPR

RPR OLLIE CHAIR Bedienungsanleitung

kingsley-bate

kingsley-bate MC-55 Bedienungsanleitung

Weltevree

Weltevree Carrier Bedienungsanleitung

Grange Fencing

Grange Fencing Elite Arch Bedienungsanleitung

Grosfillex

Grosfillex AUVENT YR14 Bedienungsanleitung

X-METAL

X-METAL EAGLE 33511 Bedienungsanleitung

Anova

Anova FBW6R Bedienungsanleitung

Outsunny

Outsunny 84A-090 Bedienungsanleitung

Ivy Terrace

Ivy Terrace IVTD212 Bedienungsanleitung

Breezesta

Breezesta FANBACK ADIRONDACK AD-0101 Bedienungsanleitung

hanit

hanit SUTTON 1 Bedienungsanleitung