Gira 1289 00 Bedienungsanleitung

Operating Instructions

Switching actuator

1289 00

Table of contents

Device description ....................................................... 4

Operating elements and indicators .............................. 5

Connection terminals................................................... 7

Mounting ................................................................... 8

Setting operating mode ............................................... 9

Switching operating mode after programming........... 10

Information on programming..................................... 11

"Schalten" (Switching) operating mode...................... 12

"Timer/sek." operating mode...................................... 14

"Timer/min." operating mode ..................................... 16

"Impuls" (Pulse) operating mode................................ 18

"Türöffner" (Door opener) operating mode ................. 20

Deleting assignments of the switching actuator ........ 23

Application example "Switching illumination" ............ 24

Application example "Additional signalling" ............... 26

Technical data........................................................... 28

Acceptance of guarantee.......................................... 29

Device description

The switching actuator is part of the Gira

door communication system.

Switching functions operated via the

2-wire bus are executed via the potential-

free relay contact of the switching actua-

tor.

Operating elements and indicators

"Progr." button

The "Progr." button has two functions:

1. Starting programming mode of the

switching actuator: If the "Progr." but-

ton is pressed for 3 seconds while the

system is in programming mode, the

programming mode of the switching

actuator is started. The "Progr." LED

flashes in programming mode.

Briefly pressing the "Progr." button

exits programming mode of the

switching actuator.

2. Actuation of the connected device. By

briefly pressing the "Progr." button in

the operating mode, the connected

device is activated based on the set

operating mode. The "Progr." LED illu-

minates during the switching time.

Exiting switching actuator

programming mode

When exiting programming mode at the

control unit, switching actuator pro-

gramming mode is also exited.

"Funktion" button

The required operating mode can be set

with the "Funktion" button (see Page 9).

The next operating mode is selected with

each button press.

The LEDs next to the operating mode

names indicate the active operating

move.

Adjuster

The activation duration of the connected

device is set at the adjuster. Depending

on the selected operating mode, the set-

ting time lies in the range 1 to 10 seconds

or 1 to 10 minutes. The adjuster is set

with a screwdriver (3 mm blade).

LED indication

The LEDs only illuminate while the door

communication system is in program-

ming mode. The LEDs go out 2 minutes

after programming mode is exited. By

pressing the "Funktion" button, the LED

indication can be activated in normal

operation for 2 minutes.

Connection terminals

Bus

The switching actuator is connected to

the 2-wire bus via these terminals. Polar-

ity need not be taken into account here,

as the polarity of the Gira door communi-

cation system 2-wire bus is neutral.

Binary in

One or more mechanical buttons (NO

contact), used to initiate the switching

functions, can be connected to the binary

input.

Potential-free relay contact

The device to be switched is connected to

the relay contact.

It could be a light or a door opener, for

example, depending on the selected

operating mode.

Max. cable length

The maximum cable length between the

binary input of the switching actuator

and the button is 20 m.

Mounting

For installation protected from dripping

and sprayed water, mount the control unit

to a top-hat rail in the distribution.

The device connection and bus connec-

tion are made via terminal screws.

The relay contact must be protected with

a 10 A miniature circuit-breaker.

Attention

Installation and mounting of electrical

devices may only be carried out by a

qualified electrician.

Setting operating mode

The switching actuator can be used in five

different operating modes:

• Schalten (Switching, see Page 12)

• Timer/sek. (Timer/sec., see Page 14)

• Timer/min. (Timer/min., see Page 16)

• Impuls (Pulse, see Page 18)

• Türöffner (Door opener, see Page 20)

Proceed as follows to select the desired

operating mode:

1. Start programming mode at the

control unit by pressing the "System-

progr." button for 3 seconds until the

LED next to the button starts flashing.

✓The LED of the last set operating mode

flashes at the switching actuator.

2. Press the "Funktion" button at the

switching actuator several times until

the LED of the desired operating mode

flashes.

3. Press the "Systemprogr." button at the

control unit to exit operation-selection

mode of the switching actuator.

✓The last set operating mode is acti-

vated.

Switching operating mode after programming

If the operating mode of a previously pro-

grammed switching actuator was

switched, the programming remains in

tact.

When only switching between switching

functions, e.g. from "Schalten" to "Timer/

min.", the switching function with the

modified conditions is executed.

When switching to or from the "Türöffner"

operating mode, no functions are exe-

cuted. In this case, the existing assign-

ments must first be deleted (see Page 23)

in order to teach in new assignments suit-

able for the operating mode.

Inhaltsverzeichnis

Andere Gira Controller Handbücher

Gira

Gira 0399 00 Bedienungsanleitung

Gira

Gira One Bedienungsanleitung

Gira

Gira One 5062 00 Bedienungsanleitung

Gira

Gira 0425 00 Bedienungsanleitung

Gira

Gira G1 Bedienungsanleitung

Gira

Gira 5423 00 Bedienungsanleitung

Gira

Gira 5023 00 Bedienungsanleitung

Gira

Gira 2100 Series Bedienungsanleitung

Gira

Gira 0309 00 Bedienungsanleitung

Gira

Gira 1039 00 Bedienungsanleitung

Gira

Gira 0566 Series Bedienungsanleitung

Gira

Gira KNX 213900 Bedienungsanleitung

Gira

Gira 2101 Series Bedienungsanleitung

Gira

Gira 2164 00 Bedienungsanleitung

Gira

Gira One 5061 00 Bedienungsanleitung

Gira

Gira Powernet Single Switching Actuator Bedienungsanleitung

Gira

Gira One 5065 00 Bedienungsanleitung

Gira

Gira KNX 5062 00 Bedienungsanleitung

Gira

Gira KNX 2139 00 Bedienerhandbuch

Gira

Gira 5431 00 Bedienungsanleitung

Gira

Gira KNX 1039 00 Bedienungsanleitung

Gira

Gira KNX 5061 00 Bedienungsanleitung

Gira

Gira 2114 00 Bedienungsanleitung

Gira

Gira System 3000 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung