Giropes Baxtran BAP Bedienungsanleitung

V.1

070121

EN - ES - FR

PRECISION SCALE CLASS II

BALANZA DE PRECISIÓN CLASE II

BALANCE DE PRÉCISION CLASS II

BAP

El fabricante se reserva el derecho de modificar sin previo aviso las características de sus productos para introducir mejoras técnicas o cumplir con nuevas regulaciones oficiales./Le

constructeur se réserve le droit de modifier les caractéristiques de ses produits en vue d’y apporter des améliorations techniques ou de respecter de nouvelles réglamentations./The

manufacturer reserves the right to modify the specifications of its products in order to make technical improvements or comply with new regulations.

marca propiedad de | est une marque de | trade mark propiety of:

Pol. Empordà Internacional Calle Molló 3

17469 VILAMALLA - (Girona) SPAIN

T. (34) 972 527 212 - F. (34) 972 527 211

ENENUSER MANUAL BAR

1. Precautions before using the balance 4

2. Name and type of the instrument 4

3. The Display and Keypad 4

3.1 Construction 4

3.2 Display description 4

3.3 Keypad function 5

4. Functions and Operation 6

4.1 Power up 6

4.2 Weighing mode 6

4.3 Counting mode 7

4.4 Percent (%) weighing mode 8

4.5 Density calculation mode (Optional) 8

5. Parameter Set-up 11

5.1 To choose the Auto. off time 11

5.2 To choose RS-232 transmission method 12

5.3 Label format 12

5.4 To choose Baud Rate 12

5.5 Data bits 13

5.6 To choose U.Wt recomputing 13

5.7 Backlight mode 13

6. RS232 Interface 14

7. Error Message 15

8. Weight Conversion 15

ENENUSER MANUAL BAR

1. PRECAUTIONS BEFORE USING THE BALANCE

For safe and dependable operation of this balance, please comply with the following safety precautions:

• Verify that the input voltage printed on the AC Adapter and the plug type matches the local AC power supply.

• Make sure that the power cord does not pose a potential obstacle or tripping hazard.

• Disconnect the scale from the power supply when cleaning the scale.

• Do not operate the scale in hazardous or unstable environments.

• Do not immerse the scale in water or other liquids.

• Do not drop loads on the platform.

• Use only approved accessories and peripherals, as available.

• Operate the scale only under ambient conditions specied in these instructions.

• Service should be performed by authorized personnel only.

• It must not be bumped against by other items or overloaded with excessively heavy weights (The load must not

exceed the maximum capacity of the balance).

• Give a warm-up for 30mins before using the scale.

2. NAME AND TYPE OF THE INSTRUMENT

The BAP model weighing balance is a self-indicating weighing scale of Class II with single weighing range, an external AC

mains adapter, and an internal rechargeable battery.

The balance consists of analogue to digital conversion, microprocessor control, power supply, keyboard, and a weight dis-

play contained within a single enclosure

3.THE DISPLAY AND KEYPAD

3.1 CONSTRUCTIONS

The balance is housed in a plastic enclosure. One display is placed on the front together with keyboard. It is intended to

be used in shops as well as industrial environment.

A level indicator is xed behind the enclosure and four adjustable leveling feet are located at the bottom

3.2 DISPLAY DESCRIPTION

The LCD display is described below

If the Capacity of the balance is 600.0g, the last digit will be the auxiliary display digit (a symbol indicating the digit):

ENENUSER MANUAL BAR

If the Capacity of the balance is 300.00, 1200.0, 1500.0 and 3000.0g, the last digit will be blank in normal weighing mode

only if the EXT.D key is pressed to extend the display.

Note: Once the balance is set to be in Trade mode, neither the auxiliary display nor the extended

display function can work.

3.3 KEYPAD FUNCTION

KEY DESCRIPTION

PRIMARY FUNCTION SECONDARY FUNCTION

To power on or power off the balance.

To choose weighing, parts counting, percentage

weighing or density function mode.

To extend the display. To take samples in parts counting mode or

percentage weighing mode.

To select the available units. To increase value or page up

To subtract the container’s weight To decrease value or page down

To return the display to “0” To return to last step in setting

To select the backlight type To move the digit to right

To transmit or print the data To conrm the current setting in setting mode

ENENUSER MANUAL BAR

4. FUNCTIONS AND OPERATION

The balance can be available for operation from mains at 110~240V (50/60Hz) with an external AC/DC adapter with 12V

output voltage and an optional internal 6V rechargeable battery.

4.1 POWER-UP

When power up the balance, the display will rst show the software version for 2 seconds and then perform a self display

test. Then it will show the Calibration counting times for about 1 second. After that it will automatically establish the current

weight as a new zero reference point.

4.2 WEIGHING MODE

4.2.1 DISPLAY RANGE

The display can show weight Tare weight to Max+9e (Gross weight).

4.2.2 ZERO-SETTING

Zero-setting range: ±2% of Max

Zero-setting is only available when the load receptor is not in motion (The display is stable).

SEMI-AUTOMATIC ZERO-SETTING

When there is a minor weight displayed (without load on the pan), press ZERO key to return to the

display to zero, then the ZERO symbol appears which indicates that the display now is at the zero point.

ZERO-TRACKING

The instrument is equipped with a zero-tracking feature which operates at a speed of ±0.25e/s and only

when the indicator is at gross zero and there is no motion in the weight display.

INITIAL ZERO-SETTING

Initial zero-setting range: ±10% of Max

When the initial zero-setting range is below -10% of Max, the display shows “-------” and the buzzer

sounds. To return the display to normal mode, please adding more weights until the initial zero-setting

range is between ±10% of Max.

When the initial zero-setting range is beyond +10% of Max, the display shows “-------” and the buzzer

sounds.To return the display to normal mode, please take off weights until the initial zero-setting range

is between ±10% of Max.

4.2.3 TARE FUNCTION

Press TARE key to subtract the current displayed weight value as the tare weight value (Consecutive

tare operations are permitted). The NET symbol appears and the display will show a net weight of the

object to be weighted.

Then take off the container, the display will show a minus “-” weight value which equals to the container’s

weight.

ENENUSER MANUAL BAR

ELIMINATE THE TARE WEIGHT

To eliminate the tare weight by pressing Key with no object on the scale.

Note:

1. When performing the tare operation(s), make sure the instrument is in stable.

2. If consecutive tare operations have been performed, to clear the tare value, please remove all the

containers on the pan rst and then press key.

3. Tare range is the full capacity of balance for all models.

4.2.3 UNITS SELECTION

Press key to choose the weighing units and the display will be changed to the new value

with the units shown. There are up to 13 units of weight that can be enabled. Refer to Parameter

Set-up Section.

4.3 COUNTING MODE

In normal weighing mode, press key to enter into counting mode, and the display shows the sample size:

Press the key to select the sample size from 10, 20, 50, 100, 200, 500 y 1000.

SAMPLING

Put on some samples with a sample size the same as the current displaying one. Then

press the key and the displayed value starts ickering. Several seconds later,

the display shows as below:

below:

Take off the samples on the pan. The sampling operation is nished. Then the balance

can be used for counting.

Press key to return to normal weighing mode (Pressing key after it

returns to weighing mode will bring back to counting mode and the unit weight data is

still stored for use).

Note:

1. If a container needs to be used, press TARE key to subtract its weight before entering into the

counting mode.

2. If the unit weight is too small (less than 0.2 of a scale division), the display will show: --or-- PCS.

ENENUSER MANUAL BAR

4.4 PERCENT (%) WEIGHING MODE

In normal weighing mode, press the key twice to enter into percent weighing mode.

Press or key to change to “100.00%”.

SAMPLING

Put the item to be considered 100% on the pan and press the key. Then the

displayed value starts ickering. Several seconds later, it stops ickering.

Take off all the weight on the pan and the display shows as below:

Then the sampling operation is nished. The balance can used for percent weighing.

Press key to return to normal weighing mode. (Pressing key after it returns

to weighing mode will bring back to percent weighing mode and the unit weight data is

still stored for use).

Note:

1.If a container needs to be used, press key to subtract its weight before entering into the

counting mode.

2. If the unit weight is too small (less than 0.2 of a scale division), the display will show: --or-- PCS.

3.The memory of sampling size data will be cleared automatically every time the key is

used to select parts counting or percent weighing.

4.5 DENSITY CALCULATION MODE (Optional)

The balance can calculate sample’s density through measuring sample weight in air, weight in water and water’s density in

current temperature

PROCEDURE

Press the key 3 times in normal weighing mode to switch to density calculation

mode. Then the display shows a temperature value.

The balance can be equipped with an optional hanging hook which can be used in

Density Calculation mode.

ENENUSER MANUAL BAR

1. Open the rubber seal on the bottom of the balance.

2. Install the hanging hook.

A. CHOOSE WATER’S TEMPERATURE.

Use the thermometer to test water’s temperature in current situation. Use or

key to choose the corresponding temperature value. Press ENTER

key to conrm.

(The default value: 25 Cº)

B. Then the display shows the water’s density under the temperature you have chosen.

And press key to conrm.

For example: 0.99705ρ-L

r-L: Indicate water density

Rubber Seal

Hole for hanging hook

NO INCLUDED

ENENUSER MANUAL BAR

C. SAMPLE WEIGHT IN AIR

Then the display shows “0.00g in-A”. Hang the sample on the hook (If a container is

used, press key to subtract the container’s weight rst), the display will show the

sample’s weight in air.

In-A: Indicate weight in air

The display shows as below

Press key to conrm

D. SAMPLE WEIGHT IN WATER

Then the display shows “0.00g in-L” .Hang the sample on the hook (If a container is

used, hang the container on the hook and put it into the water, then press TARE key to

subtract the container’s weight rst), and then put the sample in the water. The display

will show a weight value, which indicates the sample’s weight in water.

in-L: Indicate weight in water

The display shows as below

Press key to conrm

E. Then the display will show a value which indicates the density of the sample. The

density calculation is nished. (ρ-O: density of the sample)

For example: “33.6841r-O”

Press key to conrm and do the density calculation of next object.

Press key to exit from the density calculation mode and return to weighing mode.

REMARKS

1. The density unit is g/cm3, so if the weighing unit is not “g” when entering into this

mode, it will automatically be changed to “g”. And when exiting from this mode, the

weighing unit will be back to the original one.

2. Press key to exit from this mode at any time.

3. Zeroing, Tarring and cancelling tare functions are available in this mode.

4. Density calculation formula:

r-ODensity of the sample

r-LDensity of the water

WASample weight in air

WLSample weight in water

Andere Handbücher für Baxtran BAP

Inhaltsverzeichnis

Sprachen:

Andere Giropes Skala Handbücher

Giropes

Giropes Baxtran DSN Bedienungsanleitung

Giropes

Giropes BAXTRAN FFN Bedienungsanleitung

Giropes

Giropes Baxtran BAP Bedienungsanleitung

Giropes

Giropes Baxtran BLUE Series Bedienungsanleitung

Giropes

Giropes Baxtran BCD Series Bedienungsanleitung

Giropes

Giropes BAXTRAN GLASSKS Bedienungsanleitung

Giropes

Giropes Baxtran BAR Series Bedienungsanleitung

Giropes

Giropes Baxtran XTI Bedienungsanleitung

Giropes

Giropes Baxtran BS-TRI Bedienungsanleitung

Giropes

Giropes Baxtran BAR Bedienungsanleitung

Giropes

Giropes BAXTRAN SCU Bedienungsanleitung

Giropes

Giropes Baxtran BOC-P Bedienungsanleitung

Giropes

Giropes Baxtron BC Series Bedienungsanleitung

Giropes

Giropes Baxtran ACM 2 Bedienungsanleitung

Giropes

Giropes Baxtran SW Bedienungsanleitung

Giropes

Giropes BAXTRAN STEELKS Bedienungsanleitung

Giropes

Giropes BAXTRAN GREENKS Bedienungsanleitung

Giropes

Giropes Baxtran TOUCH Series Bedienungsanleitung

Giropes

Giropes BAXTRAN ABD Bedienungsanleitung

Giropes

Giropes Baxtran PS Bedienungsanleitung

Giropes

Giropes BAXTRAN APC Bedienungsanleitung

Giropes

Giropes Baxtran XTI Bedienungsanleitung

Giropes

Giropes Baxtran STI Bedienungsanleitung

Giropes

Giropes BAXTRAN STX1 Bedienungsanleitung

Beliebte Skala Handbücher anderer Marken

AWS

AWS ZEO-50 Bedienungsanleitung

Gima

Gima Glass Body Fat Analyzer Stücklistenhandbuch

Seca

Seca 374 Bedienungsanleitung

TEC

TEC TEC SL59 SERIES Bedienungsanleitung

Axis

Axis B/E Series Bedienungsanleitung

Alecto

Alecto ACW-40 Bedienungsanleitung

Rice Lake

Rice Lake MSI-4260 IS Bedienungsanleitung

IKA

IKA RCT basic safety control Bedienungsanleitung

ADE

ADE M20011 Bedienungsanleitung

Duronic

Duronic KS3000 Bedienungsanleitung

Digi

Digi SM-720 Bedienungsanleitung

Cardinal

Cardinal CS Series Bedienungsanleitung

Korona

Korona Kastella Bedienungsanleitung

A&D

A&D FC-50Ki Bedienungsanleitung

BDA

BDA CAMARGUE Bedienungsanleitung

Tanita

Tanita HD-357 Bedienungsanleitung

Leifheit

Leifheit 03173 Bedienungsanleitung

Lumme

Lumme LU-1340 Bedienungsanleitung