Givi Misure THESI 310 Bedienungsanleitung

User Manual

Position Controller

www.givimisure.it

USER MANUAL POSITION CONTROLLER THESI 310

MT02_A37_A_TH310_GIVI_ENG rev. E Pag. 2/44

TABLE OF CONTENTS

PRELIMINARY REMARKS p. 3

INSTALLATION p. 4

DIMENSIONAL SPECIFICATIONS p. 5

REAR PANEL - CONNECTIONS p. 6

KEY - MESSAGES AND SIGNALING p. 8

DATA AND PROGRAMS RETENTION p. 10

OPERATING INSTRUCTIONS

CONFIGURATION PARAMETERS p. 11

SETTING MACHINING PROGRAMS p. 31

MANUAL OPERATION p. 34

SEMI-AUTOMATIC OPERATION p. 35

AUTOMATIC OPERATION p. 37

INPUTS p. 39

OUTPUTS p. 40

ADDITIONAL INFORMATION

CONFIGURATION PARAMETERS: MEMO p. 41

TECHNICAL CHARACTERISTICS p. 42

WARRANTY TERMS p. 43

USER MANUAL POSITION CONTROLLER THESI 310

MT02_A37_A_TH310_GIVI_ENG rev. E Pag. 3/44

GIVI MISURE would like to thank you for purchasing the programmable position controller

MICROCOMPUTER

and confirms the excellent choice made.

Thanks to a powerful microcontroller, the instrument is completely programmable by

keyboard.

PRELIMINARY REMARKS

Disposal of waste electrical and electronic equipment (WEEE)

European Council Directive 2002/96/EC

The use of the WEEE symbol indicates that this product may not

be treated as household waste. If this product is disposed

correctly, you will help to protect the environment. For more

detailed information about the recycling of this product, please

contact your local authority, your household waste disposal

service provider or the retailer where you purchased the product.

USER MANUAL POSITION CONTROLLER THESI 310

MT02_A37_A_TH310_GIVI_ENG rev. E Pag. 4/44

W A R N I N G !

It is forbidden to switch on the instrument unless the machine on which it

is installed conforms to 2006/42/EC Directive.

All of the equipments connected to the instrument must have insulation

characteristics in compliance with the regulations in force.

The instrument can be installed only by specialized personnel, following

the instructions provided by the Manufacturer.

It is strictly forbidden to intervene on the instrument while it is powered.

POWER SUPPLY From 90 Vac to 230 Vac ±10% - 50/60 Hz or, alternatively,

24 Vac ±10% - 50/60 Hz (by means of selector). We recommend the

use of a mains power supply provided with an input filter. The power

distribution network to which the instrument is connected must be

equipped with a sectioning device in compliance with the regulations in

force, positioned closed to the instrument.

GROUNDING The instrument is connected to the ground through the power supply

terminal block. To avoid discharges, we recommend the use of a

socket with a grounding connection. In case of inadequate grounding

connections, all the accessible parts, including those apparently

protected, may generate electrical discharges.

FUSES Unplug or completely disconnect the power supply before changing

the fuses connected to the terminal block in the rear panel. Use only

delay fuses ø5x20 mm 500 mA 250 V.

PREVENTION To avoid fires or explosions, this instrument should not be used in the

presence of inflammable gases, solvents, explosives, etc.

REAR PANEL It can be removed only by specialized personnel, after disconnecting

the power supply.

INSTALLATION The measuring systems (optical scale, rotary encoder, etc.) must be

installed following the instructions provided by the Manufacturer. Start

connecting the inputs and outputs. At the end, proceed with the power

supply connection.

CATEGORY Installation category II as per Standard EN 61010-1.

INSTALLATION

USER MANUAL POSITION CONTROLLER THESI 310

MT02_A37_A_TH310_GIVI_ENG rev. E Pag. 5/44

CLEANING The front panel can be cleaned only after disconnecting power supply,

using a moist cloth. The instrument is not protected against liquid

penetration.

DO NOT USE SOLVENTS.

MAINTENANCE Not required.

DIMENSIONAL SPECIFICATIONS

DRILLING TEMPLATE: 137.2 x 67.8 mm

USER MANUAL POSITION CONTROLLER THESI 310

MT02_A37_A_TH310_GIVI_ENG rev. E Pag. 6/44

LEGEND:

= Ground connection

V ~ = Power supply from 90 Vac to 230 Vac ± 10% - 50/60 Hz

(or 24 Vac ± 10% - 50/60 Hz)

V – = Encoder power supply output (0 V)

V + = Encoder power supply output (5 V or 12 V)

A = ENCODER channel A input

B = ENCODER channel B input

Z = ENCODER channel Z input (zero reference)

PRESET = Position PRESET input

START = START input

STOP = STOP input

DEV = DEVIATION input

INC.C = INCREASE CYCLE input

COM + = Positive inputs common (12 Vdc)

COM – = Negative inputs common (0 Vdc)

EN.MOV = MOVEMENT ENABLE contact

OK.POS = OK POSITION contact

COM FS/AV = FAST/SLOW (DI) contacts common or

± 10 Vdc analog output (AN)

COM FB/0V = FEED/BACK (DI) contacts common or

0 V analog output (AN)

SLOW = SLOW contact

FAST = FAST contact

FEED = FEED contact

BACK = BACK contact

W A R N I N G !

Check the correct position of the power supply selector before powering the instrument.

REAR PANEL - CONNECTIONS

USER MANUAL POSITION CONTROLLER THESI 310

MT02_A37_A_TH310_GIVI_ENG rev. E Pag. 7/44

CONNECTIONS

USER MANUAL POSITION CONTROLLER THESI 310

MT02_A37_A_TH310_GIVI_ENG rev. E Pag. 8/44

The following keys and symbols are used in this manual, with the following meaning:

…. NUMERICAL KEYS FOR DIGIT ENTRY

KEYS USED ALSO FOR SLOW FEED / BACK MOVEMENTS IN

MANUAL OPERATION

KEYS USED ALSO FOR FAST FEED / BACK MOVEMENTS IN

MANUAL OPERATION

KEY USED TO SAVE MACHINING PROGRAMS

KEY USED TO ENABLE AUTOMATIC OPERATION

KEY USED TO STOP AXIS MOVEMENT

KEY USED TO SELECT THE OPTIONS DISPLAYED

ALSO USED TO SELECT THE ALGEBRAIC SIGN AND TO ENABLE

DEVIATION

ENTER KEY, USED TO CONFIRM DATA

ALSO USED TO ENABLE SEMI-AUTOMATIC OPERATION

KEY USED TO START AXIS MOVEMENT

* FLASHING VALUE

ySTEADY VALUE

KEY – MESSAGGES AND SIGNALING

USER MANUAL POSITION CONTROLLER THESI 310

MT02_A37_A_TH310_GIVI_ENG rev. E Pag. 9/44

The instrument provides a series of visual signals to support the user during configuration

and use.

Wrong operations are signaled with the following message:

E r r o r

that temporarily appears on the display to inform the operator that the entered key is not

compatible with the current operation.

In case of “overflow” error , i.e. the number of digits displayed is greater than the

instrument counting capacity, the error is shown on the display as:

_ _ _ _ _ _

To exit this situation, enter a compatible position in the “Position Preset” parameter.

In certain situations, the error message will be accompanied by a number, indicating the

cause of the error. For example:

E r r o r 20

The list of possible errors is provided in the table below:

Error Number Description

20 Function not present

21 Axis in motion

22 Program unavailable

23 End of memory

24 Outside measuring length limits

25 Value not permitted

90 Internal malfunctioning (request Technical Assistance)

E0 Configuration Error (request Technical Assistance)

USER MANUAL POSITION CONTROLLER THESI 310

MT02_A37_A_TH310_GIVI_ENG rev. E Pag. 10/44

When the mains power supply is disconnected, the instrument can retain in its memory all

the data and programs set. When powered off, the instrument can also store the last axis

counting position.

)

The instrument cannot consider shifts of the carriage made whenever the mains

power supply is disconnected (due to inertia, manual manoeuvres, or thermal

expansion). Whenever any of the above occurs, the position shown in the display is

unreliable; it does not represent the new position of the carriage but the one it had

prior to power disconnection.

DATA AND PROGRAMS RETENTION

Inhaltsverzeichnis

Andere Givi Misure Controller Handbücher

Givi Misure

Givi Misure THESI 320 Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch